Advertisement
2.
INTRODUCTION
Twin hammer mechanism utilises oversized hammers and specially strengthened hammer cage to pull even more torque out of the
precision air motor. Precision made components fit closely to reduce air leakage and maximize power. Flip reverse control on the rear
of the tool with 4-position air regulator on the handle base.
3.
SPECIFICATION
Model No: .......................................................... SA604
Air Consumption: ................................................... 7cfm
Breakaway Torque: ...........................1200lb.ft(1632Nm)
Drive: .................................................................. 3/4"Sq
Fastening Torque: .............................1150lb.ft(1564Nm)
Free Speed: ..................................................... 6500rpm
Inlet Size: ..........................................................1/4"BSP
Noise Power/Pressure: .............................. 108/97dB(A)
Operating Pressure: .............................................. 90psi
Vibration/Uncertainty:................................. 10.3/1.5m/s²
4.
PREPARATION
4.1.
AIR SUPPLY
4.1.1.
Ensure wrench air valve (or trigger) is in the "off" position before connecting to the air supply.
4.1.2.
You will require an air pressure of 90psi, and an air flow according to specification.
WARNING! Ensure the air supply is clean and does not exceed 90 psi while operating the wrench. Too high an air pressure and unclean
‰
air will shorten the product life due to excessive wear, and may be dangerous causing damage and/or personal injury.
4.1.3.
Drain the air tank daily. Water in the air line will damage the wrench.
4.1.4.
Clean air inlet filter weekly. Recommended hook-up procedure is shown in fig 2.
4.1.5.
Line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The minimum hose diameter should be
1/4" I.D. and fittings must have the same inside dimensions.
4.1.6.
Keep hose away from heat, oil and sharp edges. Check hose for wear, and make certain that all connections are secure.
COUPLINGS
4.2.
4.2.1.
Vibration may cause failure if a quick change coupling is connected directly to the wrench. To overcome this, connect a leader hose to
the wrench. A quick change coupling may then be used to connect the leader hose to the air line recoil hose. See figures 2 and 3.
FIG.2
5.
OPERATION
WARNING! Ensure you read, understand and apply safety instructions before use.
‰
5.1.
Only use impact sockets which are specifically designed for use with a impact wrench.
5.2.
Connect the wrench to the air hose as in section 4.
5.3.
Place the socket over the subject nut and depress the trigger to operate the wrench.
5.4.
To change direction turn the lever on the back of the body housing.
5.5.
The flow of air may be regulated by turning the knob at the base of the handle.
DO NOT use any additional force upon the wrench in order to remove a nut.
8
DO NOT allow wrench to free run for an extended period of time as this will shorten its life.
8
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product
becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and
dispose of the product and fluids according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 36 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
© Jack Sealey Limited
01284 757500
sales@sealey.co.uk
Original Language Version
DIRECTION
CONTROL
LEVEL
AIR FLOW
CONTROL
FIG.3
www.sealey.co.uk
SA604
FIG.1
TRIGGER
Issue 8 (H,3,F)
11/08/23
Advertisement
