Neither is any liability assumed for dam- the fi rmware under the license of Digital Voice Systems, Inc. ages resulting from the use of the information contained herein. Kenwood reserves the right to make changes to any products herein at any time for improvement purposes.
NX-220 GENERAL INTRODUCTION PERSONAL SAFETY SCOPE OF THIS MANUAL The following precautions are recommended for personal safety: This manual is intended for use by experienced techni- • DO NOT transmit until all RF connectors are verifi ed se- cians familiar with similar types of commercial grade com- cure and any open connectors are properly terminated.
NX-220 SYSTEM SET-UP Merchandise received Type Frequency range (MHz) RF power LCD 4-key DTMF keypad NX-220 K TX/RX 136~174 License and frequency allocated by FCC NX-220 K2 TX/RX 136~174 NX-220 K3 TX/RX 136~174 Choose the type of transceiver NX-220 E...
NX-220 REALIGNMENT 1. Modes 5. PC Mode 5-1. Preface User mode The transceiver is programmed by using a personal com- puter, programming interface (KPG-22A/22U), USB adapter Panel test mode *1 Panel tuning mode *1 (KCT-53U) and programming software (KPG-141D). The programming software can be used with a PC. Fig- PC mode Data programming mode ure 1 shows the setup of a PC for programming.
Page 6
NX-220 REALIGNMENT 2. When the POWER is switched on, you can immediately 6-3. Programming enter user mode. When the PC sends a command, the 1. Start up the firmware programming software (Fpro.exe transceiver enters PC mode, and “PROGRAM” is dis- (ver.
Page 7
NX-220 REALIGNMENT If the password is not set, the transceiver displays the User mode. The target can then be operated by the “CLONE”. same program as the source. 2. When you enter the correct password, and “CLONE” 7. The other target can be continuously cloned. When the is displayed, the transceiver can be used as the cloning [ ] key on the source is pressed while the source displays source.
NX-220 DISASSEMBLY FOR REPAIR ■ Removing the mechanical stopper (without LCD 1. Precautions for Disassembly models only) ■ Removing the selector knob and volume knob 1. Pick up and lift the tab of a mechanical stopper using a 1. Using a thin tool, insert it in the hole on the selector knob pair of tweezers.
Page 9
NX-220 DISASSEMBLY FOR REPAIR ■ Removing the speaker holder 2. Precautions for Reassembly There is a space of approximately 1mm (0.04 inch) be- ■ Apply the bond to the inside of the selector tween the center part of the front glass of the speaker circle nut and volume circle nut holder and the surface of the Display unit.
Page 10
NX-220 DISASSEMBLY FOR REPAIR ■ Forming the fl at cable Note: Refer to page 8 for how to install the channel se- lector knob and knob spring. Form the right and left end of the fl at cable as shown in the fi...
Page 11
NX-220 DISASSEMBLY FOR REPAIR ■ Assembly information (Sheet/Cushion) When “Main Parts” is changed (ordered), “Assembled Sheet/Cushion” should also be changed (ordered) together. The Sticker and Sheet etc are non-reusable parts. It requires the new one to get the radio’s performance after repairs. For example, when “Plastic Cabinet Assy (A02-4130-03 (without key)/A02-4131-03 (4-key)/A02-4132-03 (16-key))”...
NX-220 CIRCUIT DESCRIPTION 1. Overview 2. Frequency Confi guration The NX-220 is a VHF portable transceiver designed to The receiver is a double-conversion superheterodyne operate in the frequency range of 136 to 174MHz. The unit using the first intermediate frequency (IF) of 49.95MHz consists of a receiver, transmitter, phase-locked loop (PLL) and the second IF of 450kHz.
Page 13
NX-220 CIRCUIT DESCRIPTION 3-2. IF circuit 3-3. Audio amplifi er circuit The fi rst IF signal is passed through a four-pole monolithic Audio processing (high-pass filter, low-pass filter, de- crystal fi lter (XF1) to reject adjacent channel signals. The fi l- emphasized and so on) at FM mode and decoding at NXDN tered fi...
Page 14
NX-220 CIRCUIT DESCRIPTION 4-3. VOX 4-5. APC circuit The DSP detects the audio level. If the detected level be- The APC circuit always monitors the current flowing comes higher than the threshold level, the VOX starts. through the RF power amplifi er (Q104) and keeps a constant current.
Page 15
NX-220 CIRCUIT DESCRIPTION When the frequency is controlled by the PLL, the fre- The modulation signal is digital data of a sampling fre- quency convergence time increases as the frequency differ- quency of 96kHz set for the PLL IC by the DSP (IC603) ence increases when the set frequency is changed.
Page 16
NX-220 CIRCUIT DESCRIPTION 6-3. LCD 7. Power Supply Circuit The LCD is controlled using the 4 serial lines (SDI0, / The battery voltage (+B) is provided from the battery LCDCS, SCK0, SDO0) from the ASIC (IC610). terminal on the TX-RX unit (X57). The battery voltage passes through the 2.5A fuse (F1), and goes to the RF fi...
NX-220 COMPONENTS DESCRIPTION Display unit (X54-3760-XX) Ref. No. Part Name Description Ref. No. Part Name Description IC609 Buffer (Clock) ASQ BPF IC610 ASIC AF LPF/MIC amplifi er IC611,612 AND gate (2 input) D/A converter IC613 Motion sensor VCO MOD/VREF IC901 AF power amplifi...
Page 19
NX-220 COMPONENTS DESCRIPTION Ref. No. Part Name Description Ref. No. Part Name Description Variable capaci- D105,106 Diode Antenna switch D411 Assist tune tance diode Variable capaci- D202~204 BPF tune D412,413 Diode T/R switch tance diode Variable capaci- D414 Diode Speed up D206 BPF tune tance diode...
NX-220 PARTS LIST 2 2 0 CC45 Color* 010 = 1pF 0 = 22pF 1 = Type ... ceramic, electrolytic, etc. 4 = Voltage rating 100 = 10pF 2 = Shape ... round, square, etc. 5 = Value 101 = 100pF Multiplier 3 = Temp.
Page 21
NX-220 PARTS LIST ✽ New Parts. indicates safety critical components. L : Scandinavia K : USA P : Canada Parts without Parts No. are not supplied. Y : PX (Far East, Hawaii) T : England E : Eu rope Les articles non mentionnes dans le Parts No. ne sont pas fournis. C : China X : Australia M : Oth er Areas...
Page 22
NX-220 PARTS LIST DISPLAY UNIT (X54-3760-XX) Desti- Desti- Ref. No. Ad dress Parts No. Description Ref. No. Ad dress Parts No. Description parts nation parts nation CK73HB1H472K CHIP C 4700PF RK73HB1J823J CHIP R 1/16W CC73HCH1H181J CHIP C 180PF RK73HB1J100J CHIP R 1/16W CK73HB1A104K CHIP C...
Page 23
NX-220 PARTS LIST DISPLAY UNIT (X54-3760-XX) TX-RX UNIT (X57-8040-10) Desti- Desti- Ref. No. Ad dress Parts No. Description Ref. No. Ad dress Parts No. Description parts nation parts nation ✽ S1-4 S70-0516-05 TACT SWITCH C144 CC73GCH1H180G CHIP C 18PF ✽ S70-0519-05 TACT SWITCH K2,E2...
Page 24
NX-220 PARTS LIST TX-RX UNIT (X57-8040-10) Desti- Desti- Ref. No. Ad dress Parts No. Description Ref. No. Ad dress Parts No. Description parts nation parts nation C247 CC73HCH1H030B CHIP C 3.0PF C434 CC73HCH1H101J CHIP C 100PF C249 CC73HCH1H180G CHIP C 18PF C437,438 CC73HCH1H101J...
Page 25
NX-220 PARTS LIST TX-RX UNIT (X57-8040-10) Desti- Desti- Ref. No. Ad dress Parts No. Description Ref. No. Ad dress Parts No. Description parts nation parts nation C520 CK73HB1A104K CHIP C 0.10UF C680 CK73HB1A105K CHIP C 1.0UF C521 CK73GB0J106K CHIP C 10UF C681 CK73HB1A104K...
Page 26
NX-220 PARTS LIST TX-RX UNIT (X57-8040-10) Desti- Desti- Ref. No. Ad dress Parts No. Description Ref. No. Ad dress Parts No. Description parts nation parts nation L115 L34-4569-05 AIR-CORE COIL CP601 RK74HB1J104J CHIP-COM 100K 1/16W L116 L34-4568-05 AIR-CORE COIL CP602 RK74HB1J103J CHIP-COM 10K 1/16W...
Page 27
NX-220 PARTS LIST TX-RX UNIT (X57-8040-10) Desti- Desti- Ref. No. Ad dress Parts No. Description Ref. No. Ad dress Parts No. Description parts nation parts nation R217 RK73HB1J104J CHIP R 100K 1/16W R422 RK73HB1J106J CHIP R 1/16W R220 RK73HB1J105J CHIP R 1.0M 1/16W R423...
Page 28
NX-220 PARTS LIST TX-RX UNIT (X57-8040-10) Desti- Desti- Ref. No. Ad dress Parts No. Description Ref. No. Ad dress Parts No. Description parts nation parts nation R529 RK73HB1J000J CHIP R 1/16W R908 RK73HB1J334J CHIP R 330K 1/16W R530-533 RK73HB1J104J CHIP R 100K 1/16W R909...
Page 29
NX-220 PARTS LIST TX-RX UNIT (X57-8040-10) Desti- Desti- Ref. No. Ad dress Parts No. Description Ref. No. Ad dress Parts No. Description parts nation parts nation IC904 TC75S51FE(F) MOS-IC Q102 2SC4926YD TRANSISTOR Q103 RD01MUS1-T113 Q104 RD07MUS2BT112 Q105 2SC5383-T111 TRANSISTOR Q106 RT1N441U-T111 TRANSISTOR Q107...
NX-220 EXPLODED VIEW 16 (K,E3) 3 (K3,E) MIC1 (C/3) K2,K3,E,E2 K2,E2 K,E3 Display unit (X54-376 A/3) Fx14 TX-RX unit (X57-804) S101 X54 (B/3) A : N09-2438-05 46x2 B : N09-6608-05 C : N14-0864-04 D : N14-0865-04 E : N30-3006-43 F : N83-2005-48 Parts with the exploded numbers larger than 700 are not supplied.
NX-220 TROUBLE SHOOTING Fault Diagnosis of the BGA (Ball Grid Array) IC ■ Overview A fl owchart for determining whether or not the transceiver can be powered on (the LCD does not function even if the power switch is turned on) due to broken BGA parts. ■...
Page 33
NX-220 TROUBLE SHOOTING ● The LCD displays control *1 When an abnormal value is confirmed. Points to be checked Normal voltage If the /LCDCS is 0V or 3.3V, the ASIC/FLASH/SRAM may be broken. /LCDCS R667 3.3V→0V→3.3V When a normal value is confirmed. The LCD does not function even if it is exchanged with the Display unit.
Page 34
Trunking System following the new ESN. the Service TX-RX unit (X57-8040-11) and the schematic • When a new printed circuit board is used, the Kenwood diagram of the original TX-RX unit (X57-8040-10). (R4 is ESN changes, as does the Transceiver Information display connected with GND (ground) only.)
NX-220 ADJUSTMENT (K TYPE) Controls “ ” not appears on the LCD display Function Display Power switch/ Selector Volume Use as the DTMF keypad. [0] to [9] If a key is pressed during transmission, the DTMF [#], [ ] corresponding to the key that was presses is sent.
Page 36
NX-220 ADJUSTMENT (K TYPE) ■ Frequency and Signaling Panel Tuning Mode The transceiver has been adjusted for the frequencies (K2 and K3 models only) shown in the following table. When required, readjust them ■ Transceiver tuning (To enter tuning mode) following the adjustment procedure to obtain the frequen- To enter tuning mode, press the [ ] key while the trans- cies you want in actual operation.
Page 37
NX-220 ADJUSTMENT (K TYPE) ■ Adjustment item supplement Adjustment Item Description “Counterclockwise Volume” is adjusted at the minimum volume position. Counterclockwise Volume “Clockwise Volume” is adjusted at the maximum volume position. These adjustments can correct the volume variation. Both “Counterclockwise Volume” and “Clockwise Volume” must be adjusted. Clockwise Volume (The curve data of volume is applied.) The lock voltage of VCO (Receive) is adjusted.
Page 38
NX-220 ADJUSTMENT (K TYPE) ■ Adjustment item and Adjustment range NV (NXDN Very Adjusutment Panel Adjust item (Analog Wide) (Analog Narrow) (NXDN Narrow) Narrow) Order item tuning test Number Adjustment range 1 point ADJ Counterclockwise Common ✓ ✓ Volume Section 2 1~256 1 point ADJ Common...
Page 39
NX-220 ADJUSTMENT (K TYPE) NV (NXDN Very Adjusutment Panel Adjust item (Analog Wide) (Analog Narrow) (NXDN Narrow) Narrow) Order item tuning test Number Adjustment range - *1 Receiver ✓ ✓ Low RSSI Section 6 1~256 - *1 Receiver ✓ ✓ High RSSI Section 7 1~256...
Page 40
NX-220 ADJUSTMENT (K TYPE) ] hold [Side2] DTMF Deviation DTMF Deviation Narrow Wide DTMF DTMF ] press ] hold [Side2] Single Tone Deviation Single Tone Deviation Wide Narrow TONE TONE ] press ] hold [Side2] MSK Deviation MSK Deviation Narrow Wide ] press ] hold...
Page 41
■ Nut wrench In order to turn the volume nut and the channel selector nut, use a recommendation tool. + Terminal (Red) KENWOOD part No.: W05-1123-00 – Terminal (Black) ■ Battery Jig (W05-0909-00) Connect the power cable properly between the battery...
Page 42
NX-220 ADJUSTMENT (K TYPE) Radio Check Section Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel test mode PC test mode Unit Terminal Unit Parts Method equipment 1. Frequency 1) CH-Sig: 1-1 1) Test Channel f. counter Panel Check an internal 155.099962~ check PTT: ON...
Page 43
NX-220 ADJUSTMENT (K TYPE) Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel test mode PC test mode Unit Terminal Unit Parts Method equipment 4. MIC 1) CH-Sig: 1-1 1) Test Channel Deviation Panel Adjust AG input 12.5mV±5.8mV sensitivity AG: 1kHz Channel: 1 meter...
Page 44
NX-220 ADJUSTMENT (K TYPE) Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment 4. Receive * This adjustment can [Manual Adjustment] Panel [PC test [PC test mode] 2.5V±0.1V Assist be performed only 1) Adj item: [Receive...
Page 45
NX-220 ADJUSTMENT (K TYPE) Transmitter Section Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment 1. High 1) Adj item: [HPWR] 1) Adj item: [High Power meter Panel Panel [Panel 5.0W...
Page 46
NX-220 ADJUSTMENT (K TYPE) Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment Maximum 1) Adj item: [NDEV] 1) Adj item: [Maximum Deviation Panel Panel [Panel 1337Hz 1311~1363Hz Deviation Adjust: [✳✳✳✳] Deviation (NXDN...
Page 47
NX-220 ADJUSTMENT (K TYPE) Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment 6. QT 1) Adj item: [QT] 1) Adj item: [QT Deviation Panel Panel [Panel Write the value as 0.35kHz±0.05kHz Deviation Adjust: [✳✳✳✳.]...
Page 48
NX-220 ADJUSTMENT (K TYPE) Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment 9. DTMF 1) Adj item: [DTMF] 1) Adj item: [DTMF Deviation Panel Panel [Panel Write the value as 1.25kHz±0.05kHz Deviation Adjust: [✳✳✳✳.]...
Page 49
NX-220 ADJUSTMENT (K TYPE) Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment 12. CW ID 1) Adj item: [CWID] 1) Adj item: [CW ID Deviation Panel Panel [Panel Write the value as 1.00kHz±0.10kHz...
Page 50
NX-220 ADJUSTMENT (K TYPE) ■ Necessary Deviation adjustment item for each signaling and mode The following shows the necessary adjustment items for each signaling deviation. Please read the following table like the following example. In the case of the signaling “QT (Wide)”, this signaling is composed of three elements [Balance, Maximum Deviation (Analog Wide) and QT Deviation (Wide)]. Please adjust Balance and Maximum Deviation (Analog Wide) before adjusting QT Deviation (Wide).
Page 51
NX-220 ADJUSTMENT (K TYPE) Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment 2. Sensitivity 1 * This adjustment can 1) Adj item: [Sensitivity 1] Panel [PC test Write the value as Note: be performed only...
Page 52
NX-220 ADJUSTMENT (K TYPE) Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment 5. Open 1) Adj item: [SQL] 1) Adj item: [Open Panel [Panel tuning mode] “Open Squelch” Squelch *6 Adjust: [✳✳✳.] Squelch (Analog...
Page 53
NX-220 ADJUSTMENT (K TYPE) Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment 1) Adj item: [LRSS] 1) Adj item: [Low Panel [Panel tuning mode] Adjust with the ana- RSSI at Adjust: [✳✳✳] RSSI (NXDN Very...
NX-220 ADJUSTMENT (E TYPE) Controls “ ” not appears on the LCD display Function Display Power switch/ Selector Volume Use as the DTMF keypad. [0] to [9] If a key is pressed during transmission, the DTMF [#], [ ] corresponding to the key that was presses is sent.
Page 55
NX-220 ADJUSTMENT (E TYPE) ■ Frequency and Signaling Panel Tuning Mode (E and E2 models only) The transceiver has been adjusted for the frequencies ■ Transceiver tuning (To enter tuning mode) shown in the following table. When required, readjust them To enter tuning mode, press the [ ] key while the trans- following the adjustment procedure to obtain the frequen- ceiver is in test mode.
Page 56
NX-220 ADJUSTMENT (E TYPE) ■ Adjustment item supplement Adjustment Item Description “Counterclockwise Volume” is adjusted at the minimum volume position. Counterclockwise Volume “Clockwise Volume” is adjusted at the maximum volume position. These adjustments can correct the volume variation. Both “Counterclockwise Volume” and “Clockwise Volume” must be adjusted. Clockwise Volume (The curve data of volume is applied.) The lock voltage of VCO (Receive) is adjusted.
Page 57
NX-220 ADJUSTMENT (E TYPE) ■ Adjustment item and Adjustment range AW (Analog AS (Analog AN (Analog NN (NXDN NV (NXDN Adjusutment Panel Very Narrow) Adjust item Wide 5k) Wide 4k) Narrow) Narrow) Order item tuning test Number Adjustment range 1 point ADJ Counterclockwise Common ✓...
Page 58
NX-220 ADJUSTMENT (E TYPE) AW (Analog AS (Analog AN (Analog NN (NXDN NV (NXDN Adjusutment Panel Very Narrow) Adjust item Wide 5k) Wide 4k) Narrow) Narrow) Order item tuning test Number Adjustment range - *1 Receiver ✓ ✓ Low RSSI Section 6 1~256 - *1...
Page 60
■ Nut wrench In order to turn the volume nut and the channel selector nut, use a recommendation tool. + Terminal (Red) KENWOOD part No.: W05-1123-00 – Terminal (Black) ■ Battery Jig (W05-0909-00) Connect the power cable properly between the battery...
Page 61
NX-220 ADJUSTMENT (E TYPE) Radio Check Section Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel test mode PC test mode Unit Terminal Unit Parts Method equipment 1. Frequency 1) CH-Sig: 1-1 1) Test Channel f. counter Panel Check an internal 155.099962~ check PTT: ON...
Page 62
NX-220 ADJUSTMENT (E TYPE) Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel test mode PC test mode Unit Terminal Unit Parts Method equipment 5. Sensitivity 1) CH-Sig : 1-1 1) Test Channel Panel Check 12dB SINAD or check SSG output Channel: 1 AF VTVM...
Page 63
NX-220 ADJUSTMENT (E TYPE) Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment 4. Receive * This adjustment can 1) Adj item: [Receive Panel [PC test [PC test mode] 2.5V±0.1V Assist be performed only...
Page 64
NX-220 ADJUSTMENT (E TYPE) Transmitter Section Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment 1. High 1) Adj item: [HPWR] 1) Adj item: [High Power meter Panel Panel [Panel 5.0W...
Page 65
NX-220 ADJUSTMENT (E TYPE) Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment Maximum 1) Adj item: [NDEV] 1) Adj item: [Maximum Deviation Panel Panel [Panel 1337Hz 1311~1363Hz Deviation Adjust: [✳✳✳✳] Deviation (NXDN...
Page 66
NX-220 ADJUSTMENT (E TYPE) Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment Maximum 1) Adj item: [ADEV] 1) Adj item: [Maximum Deviation Panel Panel [Panel 4200Hz 4150~4250Hz Deviation Adjust: [✳✳.✳.✳.] Deviation (Analog...
Page 67
NX-220 ADJUSTMENT (E TYPE) Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment 7. DQT 1) Adj item: [DQT] 1) Adj item: [DQT Deviation Panel Panel [Panel Write the value as 0.35kHz±0.05kHz Deviation Adjust: [✳✳✳✳.]...
Page 68
NX-220 ADJUSTMENT (E TYPE) Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment DTMF 1) Adj item: [DTMF] 1) Adj item: [DTMF Deviation Panel Panel [Panel Write the value as 2.00kHz±0.05kHz Deviation Adjust: [✳✳✳.✳.]...
Page 69
NX-220 ADJUSTMENT (E TYPE) Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment 1) Adj item: [MSK] 1) Adj item: [MSK Deviation Panel Panel [Panel Write the value as 2.40kHz±0.05kHz Deviation Adjust: [✳✳✳.✳.]...
Page 70
NX-220 ADJUSTMENT (E TYPE) ■ Necessary Deviation adjustment item for each signaling and mode The following shows the necessary adjustment items for each signaling deviation. Please read the following table like the following example. In the case of the signaling “QT (Wide 5k)”, this signaling is composed of three elements [Balance, Maximum Deviation (Analog Wide 5k) and QT Deviation (Wide 5k)].
Page 71
NX-220 ADJUSTMENT (E TYPE) Receiver Section Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment 1. AF level [Panel test mode] 1) Test Channel Panel Panel Volume Turn the Volume 0.63V±0.1V setting 1) CH-Sig: 1-1...
Page 72
NX-220 ADJUSTMENT (E TYPE) Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment RSSI 1) Adj item: [RRSS] 1) Adj item: [RSSI Panel [Panel tuning mode] reference Adjust: [✳✳.✳.] Reference (Analog SP/MIC After input signal...
Page 73
NX-220 ADJUSTMENT (E TYPE) Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment Open 1) Adj item: [SQL] 1) Adj item: [Open Panel [Panel tuning mode] Adjust with the ana- Squelch *6 Adjust: [✳✳✳] squelch (NXDN...
Page 74
NX-220 ADJUSTMENT (E TYPE) Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment 7. High RSSI 1) Adj item: [HRSS] 1) Adj item: [High Panel [Panel tuning mode] at –80dBm Adjust: [✳✳✳.] RSSI (Analog Nar-...
Page 75
NX-220 ADJUSTMENT (E TYPE) Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment Tight 1) Adj item: [SQLT] 1) Adj item: [Tight Panel [Panel tuning mode] Remark: Squelch Adjust: [✳✳.✳.] Squelch (Analog SP/MIC...
NX-220 TERMINAL FUNCTION Display unit (X54-3760-XX A/3) Pin No. Name Function Pin No. Name Function Volume level input for audio control VOL_GND GND for volume level 33M input ENC3 Rotary switch input SCK0 Clock input SDI0 Serial data input ENC4 Rotary switch input SDO0 Serial data output...
Page 77
NX-220 TERMINAL FUNCTION SP/MIC Connector Specifi cation Signal Description Item and Condition Unit Note Name Type Input Voltage (High) PTT/RXD input PTT/RXD Digital Zin=10kΩ Input Voltage (Low) Maximum Input Voltage 1100 mVrms External MIC input AF=1kHz MICI Analog Zin=1.8kΩ@1kHz Standard Input Voltage 12.5 18.3 mVrms...
Page 92
NX-220 SCHEMATIC DIAGRAM TX-RX UNIT (X57-8040-10) L61 3 33MC BUFFER(CLOCK) 3.30V IC 6 0 9 X6 01 L614 SM 5 0 2 3 C N D H - G L77- 3 015- 05 0.03V R6 2 9 V S S 3 oUTP UT C6 74 R 633...
Page 93
NX-220 SCHEMATIC DIAGRAM TX-RX UNIT (X57-8040-10) C N502 F53-0324-05 2.5A 7.49V 7.50V L504 5.00V Li-ion AVR(50C) BATTERY REVERSE PROTECT R5 01 27 0k C N 1 C N 504 C501 4 7 0 p C50 2 AVR(33C) 4 7 0 p IC 505 C504 6 800p...
Page 94
NX-220 SCHEMATIC DIAGRAM TX-RX UNIT (X57-8040-10) /T_R /T_R C 442 R 411 C413 0.01 u L 12 0 100p C414 0.01 u L 4 2 5 3.30V TEMP CPout CPout NC_1 R 415 VCCcp NC_2 I C 4 0 3 NC_3 LD/PS C 420...
Page 95
NX-220 SCHEMATIC DIAGRAM TX-RX UNIT (X57-8040-10) /T_R 50CS 50CS R 4 53 D416,417 R:4.80V FIN FILTER TUNE T:4.80V D402,405,409 RX VCO M CH 3914 ( 7) - H R 446 C 45 7 C 471 ASSIST TUNE Q401 7.49V L4 05 C 440 R4 30 D 409...
Page 96
NX-220 SCHEMATIC DIAGRAM TX-RX UNIT (X57-8040-10) DRIVE AMP C 120 L10 7 R 4 74 R D 01M U S 1 -T 11 3 R:0V 4.7n Q 103 100p T:0.53V D4 1 2 , 4 1 3 PRE DRIVE AMP T/R SW C1 13 R 115...
Page 97
NX-220 SCHEMATIC DIAGRAM TX-RX UNIT (X57-8040-10) FINAL AMP D10 2,103 L 113 RD 0 7 M U S 2 B T11 2 ANT SW Q104 s t r i p l i n e L 1 1 0 L 1 1 1 L 112 C14 5 C14 7...
Audio Distortion ..........Less than 3% Modulation ..........16K0F3E, 11K0F3E, 8K30F1E, 8K30F1D, 8K30F7W, 4K00F1E, 4K00F1D, 4K00F7W, 4K00F2D Analog measurements made per TIA/EIA 603 and specifi cations shown are typical. Kenwood reserves the right to change specifi cations without prior notice or obligation.
Page 103
Modulation ............16K0F3E, 14K0F3E, 14K0F2D, 12K0F2D, 8K50F3E, 7K50F2D, 8K30F1E, 8K30F1D, 8K30F7W, 4K00F1E, 4K00F1D, 4K00F7W, 4K00F2D Analog measurements made per EN standards or TIA/EIA 603 and specifi cations shown are typical. Kenwood reserves the right to change specifi cations without prior notice or obligation.
Page 104
Suite 2504, 25/F, Tower 2, Nina Tower, No. 8 Yeung Uk Road, Bp 58416 Villepinte, 95944 Roissy Ch De Gaulle Cedex Tsuen Wan, New Territories, Hong Kong KENWOOD House, Dwight Road, Watford, Herts., 1 Ang Mo Kio Street 63, Singapore 569110 WD18 9EB United Kingdom...
Page 105
NX-220 NX-220 PC BOARD PC BOARD DISPLAY UNIT (X54-3760-XX) -10: K3, E -11: K2, E2 -12: K, E3 DISPLAY UNIT (X54-3760-XX) -10: K3, E -11: K2, E2 -12: K, E3 Component side view (J79-0312-09) Component side view (J79-0312-09) J79-0312 -09 C/3 –...
Page 106
NX-220 NX-220 PC BOARD PC BOARD DISPLAY UNIT (X54-3760-XX) -10: K3, E -11: K2, E2 -12: K, E3 DISPLAY UNIT (X54-3760-XX) -10: K3, E -11: K2, E2 -12: K, E3 Foil side view (J79-0312-09) Foil side view (J79-0312-09) MIC+ J79-0312-09 MIC–...
Page 107
NX-220 NX-220 PC BOARD PC BOARD TX-RX UNIT (X57-8040-10) Component side view (J79-0313-19) TX-RX UNIT (X57-8040-10) Component side view (J79-0313-19) J79-0313-19 Q106 C237 D502 R234 R165 R161 /FLDM Q510 IC201 C668 R507 R519 R529 IC101 R552 IC605 C178 R228 R224 C549 D501 IC502...
Page 108
NX-220 NX-220 PC BOARD PC BOARD TX-RX UNIT (X57-8040-10) Foil side view (J79-0313-19) TX-RX UNIT (X57-8040-10) Foil side view (J79-0313-19) J79-0313-19 C204 C244 R226 R220 C223 R131 C152 D204 R231 C235 C202 D105 D202 D203 R235 C160 R205 D206 L207 R236 C201 Q202...
Page 109
TX-RX UNIT (X57-8040-10) L CD X54-3760-XX R61 R62 R63 R64 R65 R66 R67 R69 R70 R71 R72 R73 R 84 X54-3760-XX K3,E 3.3k 3.3k 3.3k 3.3k 6.8k 470 2.2k /T_R /T_R /T_R 0-10 K3,E 50CS 50CS K2,E2 3.3k 6.8k 2.2k 10k R 8 6 0-11 L602...