Mitsubishi Electric CITY MULTI PLFY-WL-NEMU-E Series Operation Manual page 13

3. Operation
■
Manual vane angle (Wired remote controller)
Operation
Vane·Louver·Vent. (Lossnay)
High power
Comfort
Main menu: RETURN
Cursor
F1 F2 F3 F4
ON
RETURN SELECT
MENU
OFF
HOLD
Comfort
Manual vane angle
3D i-See sensor
Setting display: SELECT
Cursor
F1 F2 F3 F4
ON
RETURN SELECT
MENU
OFF
HOLD
Manual vane angle
M-NET address
Identify unit Check button
Input display:
SELECT
Address Check
F1 F2 F3 F4
ON
RETURN SELECT
MENU
OFF
HOLD
Manual vane angle
M-NET address
Vane 4-way /2-way
Input display:Angle button
Cur. Cursor Angle
F1 F2 F3 F4
ON
RETURN SELECT
MENU
OFF
HOLD
1 Select "Comfort" from the
Operation menu, and press the
[SELECT/HOLD] button.
2 Select "Manual vane angle" with
the [F1] or [F2] button, and press
the [SELECT/HOLD] button.
3 Select the "M-NET address" for
the units to whose vanes are
to be fixed, with the [F2] or [F3]
button, and press the [SELECT/
HOLD] button.
Press the [F4] button to confirm
the unit.
The vane of only the target indoor
unit is pointing downward.
4 Select "Vane" with the [F1] button.
Select "4-way" or "2-way" with the
[F2] or [F3] button, and press the
[F4] button.
Manual vane angle
Select:
SELECT
Outlet Angle
F1 F2 F3 F4
ON
RETURN SELECT
MENU
OFF
HOLD
Manual vane angle
Setting
Note:
Do not set the draft reduction in an environment with high humidity.
Otherwise, condensation may form and drip.
■
Vane setting
No setting Step 1
Step 3 Step 4
Draft
All outlets
reduction*
Press the [SELECT/HOLD] button to save the settings.
A screen will appear that indicates the setting information is being trans-
mitted.
The setting changes will be made to the selected outlet.
The screen will automatically return to the one shown above (step 5)
when the transmission is completed.
Make the settings for other outlets, following the same procedures.
If all outlets are selected,
the unit goes into operation.
Navigating through the screens
• To return to the previous screen .......... [RETURN] button
■
Confi rmation procedure of the target unit
Manual vane angle
M-NET address
Identify unit Check button
Input display: SELECT
Address Check
F1 F2 F3 F4
5 The current vane setting will
appear.
Select the desired outlets from
1 through 4 with the [F1] or [F2]
button.
• Outlet: "1", "2", "3", "4" and "1, 2,
3, 4, (all outlets)"
Press the [F3] or [F4] button to
go through the option in the order
of "No setting (reset)", "Step 1",
"Step 2", "Step 3", "Step 4", "Step
5" and "Draft reduction*".
Select the desired setting.
* Draft reduction
The airfl ow direction for this set-
ting is more horizontal than the
airfl ow direction for the "Step 1"
setting in order to reduce a drafty
feeling. The draft reduction can
be set for only 1 vane.
Step 2
Step 5
will be displayed the next time
1 Select the "M-NET address" for
the units to whose vanes are
to be fixed, with the [F2] or [F3]
button. Press the [F4] button to
confi rm the unit.
en
11