Advertisement
SPECIFICATIONS
SUMMARY OF FUNCTIONS:
6 ch in, main
Gut, pre
monitor,
post effects
(hi/low
level) out;
3 band
eq. each
channel;
master effects and reverb return to main and
monitor; dual LED
ladders; line input to main
and monitor
INPUTS, EACH CHANNEL:
1 low
Z
balanced
microphone;
1 high
Z
unbalanced line; 1 high Z unbalanced (stereo
ring) pre return
INPUTS, MASTER:
1 high Z unbalanced auxiliary each for main,
monitor,
and
effects,
1 high
Z
unbalanced
effects return; dual (bridged) phono high Z line
inputs (No RIAA)
OUTPUTS, EACH CHANNEL:
1 low Z unbalanced
(stereo tip) pre send
OUTPUTS, MASTER:
1 tow Z unbalanced line each for main, monitor,
and (high/low level) effects; reverb footswitch
CHANNEL MICROPHONE INPUTS:
Mic Impedance: Low Z 600 ohms balanced
Nominal input Level: -18 dBM, 100 mV RMS
Minimum Input Level: -44 dBM, 5 mV RMS
Maximum
input Level: *22 dBM, 10 Volts RMS
CHANNEL LINE (HIGH Z MIC) INPUTS:
.
Read all safety and operating instructions before using this
product.
.
Alt safety and operating instructions should be retained for
` future reference.
.
Obey all cautions in the operating instructions and on the
back of the unit.
.
All operating instructions should be followed.
91983
Printed in U.S.A.
.
This product should not be used near water, i.e. a bathtub.
sink, swimming pool. wet basement, etc.
.
This product should be located so that its position does not
interfere with its proper ventilation. it should not be placed
flat against a wal! or placed in a built-in enclosure that will
impede the flow of cooling air.
-
This product should not be placed near a source of heatsuch
as
a stove,
heater,
radiator
or
another
heat
producing
amplifier.
Line impedance: Hi Z 10K ohms unbalanced
Nominal input Level: 0 dBV, 1 V RMS
Minimum Input Level: -20 dBV, 0.1
V RMS
Maximum Input Level: *30 dBV, 30 Volts RMS
CHANNEL
RETURNS
AND
AUXILIARY
INPUTS:
Line Impedance:
Hi Z 20K ohms unbalanced
Designed
Input Level: 0 ፀ8ሃ, 1 Volt RMS
LINE & EFFECTS RETURN INPUTS:
Line Impedance: Hi Z 100K ohms unbalanced
Nominal Input Level:
0 dBV,
1 VRMS
Minimum Input Level: -14 dBV, 0.2 VRMS
Maximum
Input Level: *6 dBV,
2 VRMS
MAIN, MONITOR
& EFFECTS (HIGH LEVEL)
UNBALANCED OUTPUTS:
Load Impedance: 600 ohms or greater
Nominal Output: 0 dBV, 1 V. RMS
Maximum
Output:
*18 dBV, 8 VRMS
into 50K
ohms load; *16 dBM, 5 VRMS into 600 ohms load
EFFECTS
(LOW.
LEVEL)
UNBALANCED
OUTPUT:
Load Impedance: 10K ohms or greater
Nominal Output: -12 dBV, 0.25 VRMS
Maximum Output: +6 dBV, 2 VRMS
The following specs measured
with a nominal
input gain setting of 14 dB all channels, ali levels
g
DANGER
:
EXPOSURE TO EXTREMELY HIGH NOISE LEVELS MAY CAUSE A PERMANENT HEARING LOSS. INDIVIDUALS VARY CONSIDERABLY IN SUSCEPTIBILITY TO NOISE INDUCED HEARING LOSS. BUT
NEARLY EVERYONE WILL LOSE SOME HEARING IF EXPOSED TO SUFFICIENTLY INTENSE NOISE FOR A SUFFICIENT TIME.
THE U.S. GOVERNMENT'S OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION (OSHA) HAS SPECIFIED THE FOLLOWING PERMISSIBLE NOISE LEVEL EXPOSURES:
DURATION PER DAY IN HOURS
THE PAIN
E FACEPL
í
50) 1)ክ PAINTED SURFACES NOR ANY OTHER TAPE THAT IS
B
MEDIUM OR LIGHT ADHESIVE MASKING OR MIXER LABEL TAPE IS RECOMMENDED IF TAPE IS USED. ANY TAPE LEFT ON PAINTED SURFACE FOR EXTENDED PERIODS WILL BE DIFFICULT TO
REMOVE. NEVER USE CLEAR OR SCOTCH TAPE FOR THESE APPLICATIONS.
8.
Connect only to a power supply of the type marked on the unit
adjacent to the power supply cord.
9.
Never break off the ground pin on the'power supply cord. For
more
information
on grounding write for our free booklet
"Shock Hazard and Grounding."
10.
Power
supply
cords
should. always
be handled
carefully.
Never
walk
or place
equipment
on
power
suppty
cords.
Periodically check cords for cuts or signs of stress, especially
at the plug and the point where the cord exits the unit.
.
The power supply cord should be unplugged when the unitis
to be unused for long periods of time.
.
Metal
parts
can
be cleaned
with a damp: rag. The vinyl
Covering used on some units can be cleaned with a damp rag.
or an ammonia based household cleaner if necessary.
13.
set at 0 dB, all EQ.
set flat, alt Lo 2 inputs
terminated with 600 ohms, all Hi 2 inputs and all
outputs terminated with 47K ohms.
FREQUENCY RESPONSE:
(Any in/out combination with 1 VRMS output) 0,
-2 dB, 20 Hz to 30 KHz
SYSTEM HUM & NOISE:
(All channels on)
d
-84 dBV (Hi Z line inputs)
-80 dBV (Lo Z mic inputs)
EQUIVALENT INPUT NOISE:
(20 Hz - 20.KHz, 150 ohms) -126 dBV
OVER-ALL DISTORTION:
(Any in/out combination,
20 Hz - 20 KHz
VRMS)
Less than .05% THD, TYP below .01%
EQUALIZATION:
*-15 dB 60 Hz & 8 KHz, shelving
*-15 dB 600 Hz, peak/notch
MAX. AVAILABLE
GAIN:
+14 dB main control
|
+14 dB channel control
*46 dB mic input control
*74 dB total
LED READOUT
RANGE:
-21 to *-6 dBV
POWER REQUIREMENTS:
120 VAC, 60 Hz, 20 Watts (Domestic)
SOUND LEVEL dBA, SLOW RESPONSE
90
92
95
97
100
102
PECIALLY DESIGN
OR SUCH APPLICATIONS.
Care should be taken so that objects do not falt and liquids are
not spilled into the unit through the ventilation holes or any
other openings.
.
This unit should be checked by a qualified service technician
if:
A:
The power supply cord or piug has been damaged.
B.
Anything has fallen or been spilled into the unit.
C.
Theunit does not operate correctly.
D.
The unit has been dropped or the enciosure damaged.
.
The user should not attempt to service this equipment. ልዘ
_ Service work should be done by a qualified service technician.
Due to our efforts for constant improvement,
features and specifications are subject to change without notice.
(WG
PEAVEY ELECTRONICS CORPORATION
711 A Street / Meridian,
MS 39301 / U.S.A.
480300049.
11/83
Advertisement
