Advertisement
Quick Links
Neptune
09/2023
Outdoor Pure Cube
Assembly Instructions
Requirements:
2 People (recommended)
Staple Gun
Rubber Mallet
¼" Nut Driver
Carpenters Level
Step Ladder
Carpenters Square
Utility Knife
Tape Measure
Drill Bit set
Cordless Drill
4mm Hex Bit
Phillips & Robertson Drill Bits
Saw
2" hole Saw
13mm Socket
It is highly recommended to view the assembly video prior to starting assembly!
Click here to View the assembly process or scan the QR code.
Manufactured by:
tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com
Advertisement
Related Manuals for leisurecraft pure cube Neptune
Summary of Contents for leisurecraft pure cube Neptune
- Page 1 Phillips & Robertson Drill Bits 2” hole Saw 13mm Socket It is highly recommended to view the assembly video prior to starting assembly! Click here to View the assembly process or scan the QR code. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 2 Side Wall Bench Assembly (Electric Heater Only) Inside Trim Installation Vent Kit Installation Handles and Accessories Installation Floor Model Electric Heater Installation Electric Heater Installation Wood Stove Installation (Chimney out the Side Wall) Care &Maintenance Warranty Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 3 A solid base for your sauna is recommended and can be made from any of the following. Concrete Pad Wood Deck Crushed Stone Patio Stone/Paver Blocks It is recommended to build a base larger than required to provide a sitting area for cooling off during your sauna session Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 4 Roughly center the 4 middle joists between the outside joists. Secure the outside joists to the front and back joists using 2 – 1 ½” (38mm) screws per corner. Repeat on all 4 corners. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 5 These will be the center floor joists and will be 2 joists back to back. Ensure the insulation supports are facing inwards to each side and secure with 2 – 1 ½” screws in the pre- drilled holes. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 6 (38mm) screws in the pre-drilled holes ensuring they are the same spacing as the front joist. Place the blocks of foam insulation in between the joists. You may need to trim off the end for a proper fit. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 7 For extra support, Secure every third floorboard to the inside floor joists with staples or finishing nails as well. When you get to the middle of the floor, remove the temporary floorboard that was placed earlier. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 8 You may use a rubber mallet to tap it into place. Once the last floorboard is in the proper placement, secure each of the unscrewed floorboards with a 1 ½” (38mm) screw into each joist. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
-
Page 9: Wall Assembly
Ensure it is flush to the back edge of the floor and secure with 2 – 3 ½” (89mm) screws into the back floor joist and 4 – 2 ½” (64mm) screws into the other wall panel. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com... - Page 10 2 – 3 ½” (89mm) screws into the outer floor joist and 4 – 2 ½” (64mm) screws into the previous wall panel. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 11 Secure with 4 – 2 ½” (64mm) screws through the previous wall panel into the door panel. Install the last narrow next to the door and secure to the door panel with 4 – 2 ½” (64mm) screws. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 12 The lip of the panel rigger should be tight to the bottom side of the panel. Slide the dowel through the hole in the rigger so it is even on both sides. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 13 Insert the front window panel and ensure it is flush to the front of the floor and the side wall panels. Use a rubber mallet to finesse widow until it is flush by tapping on the wood of the panel. (if needed) Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 14 Repeat on the opposite side. Once the front window is installed, secure the narrow panel on either side of the glass panel with 2 - 3 ½” (89mm) screws to the outside floor joists. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 15 Neptune Outdoor Pure Cube Assembly Instructions Front Window Installation secure the front glass panel with 4 - 2 ½” (64mm) screws to the front floor joist. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
-
Page 16: Roof Assembly
Repeat for the side wall panels ensuring the roof panel is flush to the side walls. Repeat the above steps for the 2 roof panel. Ensure the insulation blocks are already installed in the roof panels Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com... - Page 17 Ensure the plywood is flush to the front and sides of the sauna and secure with 1 ¼” (32mm) screws or staples. Repeat for the second sheet of plywood. Repeat for the last smaller sheet of plywood. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 18 Place one of the top side nosing pieces Ensure it is 1” above the bottom of the top wall panel stud. Secure the nosing to the roof panels with 9 – 2 ½” (64mm) screws. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 19 At the back of the sauna pull the membrane tight and secure with staples to the underside of the wall panels. Cut off the excess membrane even with the nosing pieces and adding more staples as needed to get a tight fit. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 20 Place a side metal trim piece over the side nosing and secure with 6 black screws on the top and 3 centered on the bottom of the metal trim. Repeat on opposite side. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 21 (3 on each side of the metal trim) Repeat on opposite side, Repeat the process for the trim at the back of the sauna only securing with screws on the outside edges of trim at this point. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 22 Place the first piece of metal siding by sliding it into the “J” side piece and then securing with 3 of the provided screws, 1 at the top, middle and bottom. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 23 On the door side of the sauna, Place a top “J” piece between the trim piece and the door and secure with 3 of the provided black screws. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 24 Install the bottom trim piece ensuring it is snug between the side “J” trim pieces securing with 3 of the provided screws. Follow the same process as the back wall for installing the metal siding pieces up to the door. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 25 Repeat for the opposite side wall of the sauna. Ensure the 2 last full piece of metal siding has the vent hole cut out towards the top. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
-
Page 26: Bench Assembly
Repeat with the lower bench ensuring the curved front of the bench is facing upwards. Secure the support to the bench with 2 – 2 ½” (64mm) screws per support ensuring the support is square to the bench. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com... - Page 27 Place the upper bench enclosure in place and secure with 2 - 1 ½” (38mm) screws into each support. Repeat for bottom enclosure. Screw between the slats of the support to make the screws less visible. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 28 Ensure the bench is tight to the side wall then secure with 2 - 2 ½” (64mm) screws in the back support and 2 - 2 ½” (64mm) screws in the floor support on each bracket. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 29 Place the side wall backrest 10” (25cm) to the bottom of the 2 slat above the bench and secure with 2 ½” (64mm) screws into each support. Screw between the slats of the support to hide the screws. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 30 Use a full piece of the corner trim for the side wall. Measure the distance remaining and cut accordingly. Repeat on opposite side wall. Repeat the above steps for the corners on the front wall. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 31 Cut accordingly and secure with staples or finishing nails. Install the crown molding over the seam between the 2 roof panels. Measure the remaining gap and cut a piece to fit. Secure it with staples or finishing nails. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
-
Page 32: Vent Installation
Only drill have way to prevent splintering on the inside of the sauna. Finish drilling the hole from the inside for a cleaner look. Install the vent and secure with the provided screws. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com... - Page 33 Secure with 3 – 1 ½” (38mm) screws. Repeat the process for removing the insulation and installing the vent for the lower vent hole. Repeat the process to install the cedar slide cover. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 34 Use a 1 ½” (38mm) screw to hang the optional thermometer in the desired location. Use 2 - 1 ½” (38mm) screws to hang the optional cedar sauna shelf in the desired location. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 35 This should be under the top bench to hide the wires coming into the sauna. ( Approx. 28”- 30” (71-76cm) from the ground) Remove the piece of metal siding to finish drilling the hole through the sauna wall. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 36 On the inside of the sauna, slide the wires along the wall under the lower bench and front enclosure to the front of the sauna where the heater and control panel will be located. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 37 Flip over the box and bracket and drill out the mounting holes from the bracket into the electrical box. Secure with the provided bolt & nuts. Mount the assembly to the wall with the provided lag screws. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 38 45° angle at that measurement. Measure the distance from the front of the lower bench to the trim piece and cut the other wire cover trim piece on a 45° angle at the measurement. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 39 Install the temperature sensor on the wall above the heater 2 ½” (64mm) down from the roof trim with the provided 1” (25mm) screw. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 40 Leave the wires for a licensed or qualified electrician to connect. Remove the protective film from the heater. Place the heater in the desired location. It must be a minimum of 3 ½” (89mm) away from all walls. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 41 9 inches of the heater Rocks should be placed until they sit to the top of the heater ensuring that the element protector is fully covered or encased with rocks. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 42 Transfer the measurements to the side wall of the sauna where the heater will be placed. Install the supplied support screws into your marks as shown. Screw them in until they are about ¼” (6mm) out of the wall. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 43 (2) – 1 ½” (38mm) screws per side. Repeat for the bottom heater guard support. Place 2- 2 ½” (64mm) screws into the pre-drilled holes on either side of heater guard to prepare for mounting. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 44 “cures” the woodwork. All wiring should be installed according to the heater manufacturers instructions and by a • licensed electrician. • Do NOT use a G.F.I breaker Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 45 Fasten the stove handle onto the stove door With the screws provided. Remove the screw on the back of stove and remove the back flap. Measure the center of the chimney hole, in this case it is 22” (56cm) Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 46 Drill a hole on the mark big enough to fit your jigsaw blade. Mark 4” (10cm) from the center of the hole in all 4 directions. Place your chimney on the 4 marks and trace out a circle. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 47 Secure the heat shield to the wall using 6- 1 ½” (38mm) screws in the provided holes. Place the floor heat shield centered to the wall shield. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 48 Level the exterior shield and mark on the outer studs where the mounting holes will be. Remove the shield and chimney and secure the support with 2 – 3 ½” (89mm) screws in each end. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 49 Place the heat shield and chimney back into position and secure in the corners with 4 of the provided screws. Assemble the remaining chimney pieces. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 50 Attach the support strap to the chimney support and tighten bolts on both sides. Install the Chimney cap on top of the Chimney pipes. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 51 This natural weathering will not harm the wood or impair the sauna’s performance. If you wish to retain the natural color of your Dundalk Leisurecraft Sauna, there are many cedar stains on the market and almost as many opinions as to which is best.
- Page 52 Children must be supervised by an adult. WARRANTY LeisureCraft warrants our saunas against defects in materials and workmanship under normal/residential use for a period of five (5) years, as applicable, from the date of receipt of the product by the original end- user consumer.