Dimensions | 21 Document Conventions This document contains general safety, installation and operation instructions for the Wisdom Audio IA- 8DSP Amplifier. It is important to read this document before attempting to use this product. Pay particular attention to: WARNING: Calls attention to a procedure, practice, condition or the like that, if not correctly performed or adhered to, could result in injury or death.
Page 4
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL. 1.
Important Safety Instructions Please read all instructions and precautions carefully and completely before operating your Wisdom Audio equipment. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this equipment near water.
Unpacking the IA-8DSP CAUTION: Do not attempt to lift your IA-8DSP while bending or twisting from the waist. Use your legs for lifting, not your back. Always stand as straight as possible and keep the IA-8DSP close to your body to reduce strain on your back.
NOTE: The AC receptacle employs a 20-amp IEC 320-C19 standard socket (not a 15-amp IEC socket). Rackmount Installation Rack mount ears are included with the IA-8DSP and IA-8DSPDSP. These allow the amplifier to be mounted in a standard 19” wide rack mount. Each amplifier requires 2RU of height.
1. Power Indicator: The international symbol for power is inscribed in this location to designate its purpose. When power is first switched on, the IA-8DSP will turn on automatically. The only way to place the unit is Standby is with the DC Trigger (above).
Page 9
• Individual Channel Blue LED OFF = Clipping Error. The LED will be OFF to indicate the channel is disabled. The IA-8DSP will disable a single channel if that channel has clipping at either the input into the amplifier module or the output of the amplifier module, and then will enable the channel after waiting 15 seconds.
Page 10
If yours is a custom installation with wires that are run in the walls, you should probably call your Wisdom Audio dealer for assistance trouble-shooting the installation.
4. AC Mains Input (IEC 320-C19) and Switch 5. Ethernet / USB system setup and diagnostics 6. DANTE Audio over IP (Optional – Dealer Installed) 7. Network Reset CAUTION! Turn off the IA-8DSP before attempting to make or change any connections. IA-8DSPDSP WISDOMAUDIO.COM...
Page 12
2. Speaker Output Terminals The Wisdom Audio SA-series amplifiers are equipped with high-current binding posts for output termination to the loudspeaker system. To take full advantage of the amplifier’s sonic quality, we recommend using high- quality speaker cable; please see your Wisdom Audio dealer.
Page 13
The 12v Trigger Output jack is driven to a “high” state of 12 volts a few seconds after the IA-8DSP is turned on and can source as much as 100 mA of current at 12 volts. This signal may be used in turn to control other components, such as additional Wisdom Audio SA-series amplifiers.
Page 14
Do not defeat the earth ground of the AC power cord. An AC mains switch is located above the power cord on the rear panel of the IA-8DSP. This switch may be used to disconnect the unit from the AC mains without having to unplug the IA-8DSP from the wall outlet.
Page 15
If the IA-8DSP cannot be located using mDNS, it can be accessed via IP address. First locate the IP address of the IA-8DSP by performing an IP scan of the network using a scanner such as the Advanced IP Scanner.
Page 16
DANTE training can be obtained by contacting www.audinate.com. Training is free and available online. Do not connect the home network to this connection unless directed by Wisdom Audio, or by an Audinate trained or DANTE certified installer.
Care & Maintenance To remove dust from the cabinet of your IA-8DSP, use a feather duster or a lint-free soft cloth. To remove dirt and fingerprints, we recommend isopropyl alcohol and a soft cloth. Dampen the cloth with alcohol first and then lightly clean the surface of the IA-8DSP with the cloth.
North American Warranty When purchased from and installed by an authorized Wisdom Audio dealer, Wisdom Audio electronic products are warranted to be free from defects in material and workmanship under normal use for a period of five years from the original date of purchase.
If your Wisdom Audio loudspeaker must be serviced, please contact your dealer. Your dealer will then decide whether the problem can be remedied locally, or whether to contact Wisdom Audio for further service information or parts, or to obtain a Return Authorization. The Wisdom Audio Service Department works closely with your dealer to solve your service needs expediently.
Specifications All specifications are subject to change at any time, in order to improve the product. • Rated power output per channel, from 20 Hz–20 kHz at <1.0% THD o 250 w/ch continuous rms power @ 4Ω; o 125 w/ch continuous rms power @ 8Ω; o Minimum Impedance: 2Ω...
Need help?
Do you have a question about the IA-8DSP and is the answer not in the manual?
Questions and answers