Bosch Professional GDX 18 V-LI Original Instructions Manual page 8

OBJ_BUCH-839-005.book Page 8 Thursday, July 14, 2016 2:27 PM
8 | English
Cordless Impact Screwdriver
Article number
Rated voltage
No-load speed
Impact rate
Maximum torque, hard screwdriving application
according to ISO 5393
Bolt size
Tool holder
Weight according to EPTA-Procedure 01:2014
Cordless Impact Screwdriver
Article number
Rated voltage
No-load speed
Impact rate
Maximum torque, hard screwdriving application
according to ISO 5393
– ¼" hexagon socket
–  ½"
Bolt size
Tool holder
Weight according to EPTA-Procedure 01:2014
*dependent of the battery pack being used
Assembly
Battery Charging
 Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the lith-
ium ion battery of your power tool.
Note: The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The Lithium-Ion battery can be charged at any time without
reducing its service life. Interrupting the charging procedure
does not damage the battery.
The Lithium-Ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
 Do not continue to press the On/Off switch after the
machine has been automatically switched off. The bat-
tery can be damaged.
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of be-
tween 0 °C and 45 °C. A long battery service life is achieved
in this manner.
Observe the notes for disposal.
1 609 92A 23R | (14.7.16)
GDS 14,4 V-LI
3 601 JA1 T..
V= 14.4
-1
min 0 –2800
-1
min 0 –3200
Nm 170*
mm M6 – M16
 ½"
kg 1.4 - 1.7*
GDX 14,4 V-LI
3 601 JB8 0..
V= 14.4
-1
min 0 –2800
-1
min 0 –3200
Nm 150*
Nm 170
mm M6 – M16
¼" hexagon socket/ ½"
kg 1.5 - 1.7*
Removing the battery
The battery 5 is equipped with two locking levels that should
prevent the battery from falling out when pushing the battery
unlocking button 6 unintentionally. As long as the battery is
inserted in the power tool, it is held in position by means of a
spring.
To remove the battery 5, press the unlocking button 6 and
pull out the battery toward the front. Do not exert any force.
Changing the Tool (see figure A
 Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
 Regularly clean the power tool's air vents. The motor's
fan will draw the dust inside the housing and excessive ac-
cumulation of powdered metal may cause electrical haz-
ards.
GDS 18 V-LI
3 601 JA1 S..
18
0 –2800
0 –3200
180*
M6 – M16
 ½"
1.5 -1.9*
GDX 18 V-LI
3 601 JB8 1..
18
0 –2800
0 –3200
160*
180
M6 – M16
¼" hexagon socket/ ½"
1.5 - 2.0*
C)
—
Bosch Power Tools