Main Accessories - Canon F-1 Quick Start Manual

MAIN ACCESSORIES
stops.
To install, you simply remove the
camera's back cover.
41)
Interval Timer TM-1 Quartz
o
Battery Cord C-FN
«i)
Data Back FN
This is a special cord for drawing the
camera's power from the alternative
power source in cold weather. The
camera's usual 6V battery is rem oved
and the power is drawn from the High
Power Ni-Cd Pack. The voltage from
the High Power Ni-Cd Pack is stepped
down to the usual voltage required for
the camera's function.
Removing the camera's back cover
also permits easy installation of the
Data Back FN. This is a data printing
device with three dials for letters,
Roman numerals and numbers. It can
be used for dating or classifying pho-
tographs. Cord connections are
unnecessary as the camera's electron-
ic circuitry automatically imprints the
information on the film in perfect syn-
chronization. Electronic flash can be
used at the same time.
This handy accessory permits unman-
ned sequential photography at any
preset time, from one shot every 1-40
seconds to one shot every 1-30
minutes. And the precision quartz
timer may be set in 14 stages on a
large, easy-to-read dial. The TM-1
releases the shutter when the camera
is used in combination with the motor
drive or power winder accessories. And
it will function as a remote control
switch.
8
100 Exposure Film Chamber
FN-100
A: 8.5mm (5/ 16" )
With its newly designed grip and built-
in shutter release button, this light-
weight, compact unit greatly improves
hand-held shooting and portability.
Rapid-sequence (up to 5 fps) shooting
of 100 frames is possible with the AE
Motor Drive FN. This makes the Film
Chamber FN-100 ideal for sports pho-
tography, copying work or recording
experiments.
B: 11 .85mm (7 / 16")
4D
Wirelesss Controller LC-1
Consisting of a receiver and transmit-
ter, the Wireless Controller LC-1 per-
mits remote-control operation, sequen-
tial or single-frame, from a distance of
60m in a straight line without cord
connection. It has three channels for
setting off cameras in succession.
Placing receivers on several cameras,
makes simultaneous multi-camera re-
mote control possible. And with the
three-channel selection, there is less
chance of another photographer using
the same or similar device accidental-
ly setting off your camera .
Its manually set subtractive frame
counter automatically disengages the
counter on the motor drive, and indi-
cates the number of exposures re-
maining at any given time. When the
film runs out, the unit automatically
o
Canon AE Power Winder FN
Specifications
C:
2.3mm (1/16")
D: 0.7mm (1 /32" )
E:
0.9mm (3 /64")
Structure: Motor drive section and power source-in-one unit
Winding Speed: Approx two frames per second for sequence
shooting or single-frame winding for intermittent shooting.
Operation : Activated by two release buttons on the winder, one
for horizontal and another for vertical or by the came ra's
shutter release button, Remote Switch 3 or 60 using connect-
ing cords, or with the transmitter of Wireless Controller LC - 1.
Shooting at fixed intervals possible using Interval Timer TM-1
Quartz.
Shutter Speed Coupling Range:
8 to 1/2000 sec .
Frame Counting:
Frame counter of the Power Winder FN shows
the number of unexposed frames . Functions independent of
camera's frame cou nter.
Film Rewinding:
By rewind crank on camera.
Safety Circuit: When the film is completely exposed or if the
battery power fails, film winding automatically stops and the
LED on Power Winder FN flashes.
Number of Film Rolls: In normal temperature about twenty rolls
of 36-exposure film in continuous or sing le-frame mode, using
ca rbon zinc batteries.
Power Source: Four
AA size batteries, carbon zincs, alkaline-
manga nese or Ni-Cd batteries
Size:
157mm(W) x 77mm(D) x 101mm(H); (6-3 / 16" x 3" x 4")
Weight: 400g, 14-1/8 ozs. (inc luding batteries)
8canon AE Motor Drive FN
Specifications
Structure:
Consists of a motor for film winding, an electro-mag-
netic c lutch, a set of gears, and a release button for connec-
tion to the camera base.
Operation:
Three shutter buttons provided inc!. battery section
and camera's) . Shooting at fixed intervals is possible using
the Interval Timer TM-1 Quartz.
Film Rewinding: Motorized rewinding taking approximately 8
sec.
Size: 157mm(W) x 94mm(H) x 72mm(D); (6-3/16" x 3-11 / 16" x
2-7/8")
Weight: 396g, 13-15/16 ozs.
SG1-A7