Advertisement
addition, connecting the power cable without the appropriate
fuse in place voids the product warranty.
1
Route the wiring harness to the power source and to the
device.
2
Connect the red wire to the positive (+) battery terminal, and
connect the black wire to the negative (-) battery terminal.
3
If necessary, install the locking ring and O-ring on the end of
the wiring harness.
4
Insert the cable into the POWER connector on the back of
the device, pushing firmly.
5
Turn the locking ring clockwise to attach the cable to the
device.
Additional Grounding Consideration
This consideration is applicable only to devices that have a
grounding screw. Not all models have a grounding screw.
This device should not need additional chassis grounding in
most installation situations.
NMEA 2000
Considerations
®
If you are connecting to an existing NMEA 2000 network,
identify the NMEA 2000 power cable. Only one NMEA 2000
power cable is required for the NMEA 2000 network to operate
properly.
A NMEA 2000 Power Isolator (010-11580-00) should be used in
installations where the existing NMEA 2000 network
manufacturer is unknown.
If you are installing a NMEA 2000 power cable, you must
connect it to the RV ignition switch or through another in-line
switch. NMEA 2000 devices will drain your battery if the NMEA
2000 power cable is connected to the battery directly.
This device can connect to a NMEA 2000 network on your RV to
share data from NMEA 2000 compatible devices such as a VHF
radio. The included NMEA 2000 cables and connectors allow
you to connect the device to your existing NMEA 2000 network.
If you do not have an existing NMEA 2000 network you can
create a basic one using cables from Garmin.
To use a FUSION
stereo and digital switching server, you must
®
connect the devices to the same NMEA 2000 network.
If you are unfamiliar with NMEA 2000, you should read the
"NMEA 2000 Network Fundamentals" chapter of the Technical
Reference for NMEA 2000 Products. You can find this document
using the "Manuals" link on the product page for your device at
www.garmin.com.
The port labeled NMEA 2000 is used to connect the device to a
standard NMEA 2000 network.
NOTICE
FUSION stereo
RV Fixed Display
Digital switching server
In-line switch
NMEA 2000 power cable
NMEA 2000 cable from the stereo
This can be extended to a maximum length of 6 m (20 ft.) using a
NMEA 2000 cable.
NMEA 2000 drop cable
NMEA 2000 drop cable
NMEA 2000 terminator or backbone cable
NMEA 2000 T-connector
Composite Video Considerations
This device allows video input from composite video sources
using the port labeled CVBS IN. When connecting composite
video, you should observe these considerations.
• The CVBS IN port uses a BNC connector. You can use a
BNC to RCA adapter to connect a composite-video source
with RCA connectors to the CVBS IN port.
• Video is not shared across the NMEA 2000 network.
Accessing the RV Builder Settings
1
Select Settings > My RV.
2
Hold the upper-left corner of the screen
The RV Builder Settings option appears in the menu.
3
Select RV Builder Settings.
The RV Builder Settings are accessible until you turn the device
off and on, or hold the upper-left corner of the screen again.
Customizing the Startup Screen
You can set your company logo or another image to be
displayed while the device is turning on. For the best fit, the
image should be 50 MB or less, should not have transparency,
and should conform to the recommended dimensions
(Recommended Startup Image Dimensions, page
1
Insert a memory card that contains the image you want to
use.
2
From the RV Builder Settings, select Startup Image >
Select Image.
3
Select the memory card slot.
4
Select the image.
5
Select Set as Startup Image.
To view the startup screen with the new image, turn the device
off and on.
4).
3
Advertisement
