Features ................................................ 6 EMI 2 – EMIZB-141 ..........................................6 Key features ............................................6 Endpoints................................................. 7 Zigbee Device Object (ZDO) ......................................7 Develco Utility ............................................7 Metering Device ........................................... 7 Supported Clusters ..........................................8 Metering cluster for EP 0x02 ...................................... 8 3.1.1 Basic –...
Page 3
Action on Power On ........................................19 General network behaviour ......................................20 Installation ............................................20 Normal – Keep alive ........................................20 5.2.1 Network lost ..........................................20 Low battery ............................................21 Specifications ............................................22 Contact Information ..........................................23 Develco Products A/S Tangen 6 http://develcoproducts.com DK-8200 Aarhus N info@develcoproducts.com...
Page 4
Develco Products assumes no responsibility for any errors, which may appear in this manual. Furthermore, Develco Products reserves the right to alter the hardware, software, and/or specifications detailed herein at any time without notice, and Develco Products does not make any commitment to update the information contained herein.
Develco Products A/S reserves the right to make changes to any product to improve reliability without further notice. Develco Products A/S does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under patent rights or the rights of third parties.
The External Meter Interface 2 comes with an optical probe, which is easily attached by a magnet. The cable length is approximately 800 mm. 2.2 Key features • LED sensor • ZigBee OTA cluster for firmware upgrades • ZigBee 3.0 certified Develco Products A/S Tangen 6 http://develcoproducts.com DK-8200 Aarhus N info@develcoproducts.com...
3 Supported Clusters Metering cluster for EP 0x02 3.1.1 Basic – Cluster id 0x0000 (Server) Only the first set has mandatory attributes, also the optional attributes that can be relevant to a Develco device are all in set 0x000. 3.1.1.1...
Relevance and ref. 0x00 Identify Query Response Uint16 - Identify Time (seconds) ZCL 3.5.2.4 3.1.4 Poll Control - Cluster id 0x0020 (Server) The poll control cluster is described in ZCL section 3.16 Develco Products A/S Tangen 6 http://develcoproducts.com DK-8200 Aarhus N info@develcoproducts.com...
EMI 2 will send a check-in command in the interval specified in attribute “Check-in Interval. The coordinator has to reply with a check-in response. If it doesn’t find a poll client, it will search again periodically. Develco Products A/S Tangen 6 http://develcoproducts.com DK-8200 Aarhus N info@develcoproducts.com...
8,388,607 Above attribute description is to be found in section 10.4.2.2.5 “Historical Consumption” in ZCL provided by the CSA 3.1.5.5 Manufacture Specific Attributes Develco Manufacture code is 0x1015. Table 1 : Formatting Attribute Set (Manufacture Specific) Identifier Name Type...
Summation setting because Pulse Configuration is used when calculating the total amount of detected pulses. 3.1.5.6 Commands The metering cluster support sending 1 command. Name Man/Opt Relevance and ref. 0x00 Get Profile Response ZCL 10.4.2.3.1 Develco Products A/S Tangen 6 http://develcoproducts.com DK-8200 Aarhus N info@develcoproducts.com...
Upgrade Server ID Address 0x0001 File Offset Uint32 0x0002 Current File Version Uint32 0x0004 Downloaded File Version Uint32 0x0006 Image Upgrade Status Enum8 0x0007 Manufacturer ID Uint16 0x0008 Image Type ID Uint16 Develco Products A/S Tangen 6 http://develcoproducts.com DK-8200 Aarhus N info@develcoproducts.com...
3 sec until a cluster match is found. When a match is found, or the cluster examine is finished the blinking stops and the device sends a message to the target device to stop the identify time. The following clusters are support in EZ-mode finding and binding: Develco Products A/S Tangen 6 http://develcoproducts.com DK-8200 Aarhus N info@develcoproducts.com...
If a device has joined a network and is powered down, it will attempt to rejoin this network upon power up. For the first 30 seconds hereafter, the device will be available for communication. This time can be expanded using the poll control cluster functionality. Develco Products A/S Tangen 6 http://develcoproducts.com DK-8200 Aarhus N info@develcoproducts.com...
When the device is in scan mode the YELLOW LED will flash once every second until it re-joins the network. According to the ZigBee specification TX is NOT allowed to be enabled all the time and a TX silent period must be defined. Develco Products A/S Tangen 6 http://develcoproducts.com DK-8200 Aarhus N info@develcoproducts.com...
The current battery voltage can be read from the power configuration cluster described in section 3.3.2.2.4. The attribute “BatteryVoltage” is measuring the battery voltage, in units of 100mV. Low batt LED indication – YELLOW LED will blink twice every 60 second. Develco Products A/S Tangen 6 http://develcoproducts.com DK-8200 Aarhus N info@develcoproducts.com...
Supports LED pulses (configurable pulse range from 50 to 10 000 pulses per Interfaces kWh) Communication Wireless protocol ZigBee 3.0 ZigBee end-device Certifications Conforming to CE, UKCA, FCC, IC, ISED, RED and RoHS directives Zigbee 3.0 certified Develco Products A/S Tangen 6 http://develcoproducts.com DK-8200 Aarhus N info@develcoproducts.com...
Need help?
Do you have a question about the EMI 2-EMIZB-141 and is the answer not in the manual?
Questions and answers