Connection To Other Equipment; Tv/Video Selection - Toshiba 20A46C Owner's Manual

ANTENNA/CABLE TV CONNECTIONS
Choose one of the following seven connections, based on your
equipment and service:
Combination VHF/UHF antenna
Single 75 ohm cable
(or)
Single 300 ohm twin-lead wire*
*
For best performance, if you have a splitter connected, remove
the splitter and connect the single wire to the transformer,
and then to the TV's antenna input (as illustrated here).
Separate VHF and UHF antennas or
Combination VHF/UHF antenna with separate cables/wires
UHF Antenna
300 ohm twin-lead wire
VHF Antenna
75 ohm cable
(or)
UHF Antenna
300 ohm twin-lead wire
VHF Antenna
300 ohm twin-lead wire*
Cable TV service
From cable
TV service
(or)
From cable
CONVERTER/ DESCRAMBLER
TV service
(or)
CONVERTER/ DESCRAMBLER
From cable
SPLITTER
TV service

CONNECTION TO OTHER EQUIPMENT

The exact arrangement you use to interconnect various video and audio components to the TV is dependent on the model and features
of each component. Check the owner's manual provided with each component for the location of video and audio inputs and outputs.
The following connection diagrams are offered as suggestions. You may need to modify them to accommodate your particular
assortment of components.

TV/VIDEO SELECTION

To view the picture from a VCR, camcorder, or VIDEO game,
you must put the TV in VIDEO mode first. Press TV/VIDEO to
select VIDEO mode. The word "VIDEO1" or "VIDEO2" displays
briefly on-screen. Press TV/VIDEO again to return to TV mode.
TV VIDEO 1
1. To connect the TV to a VCR
VCR
To Audio/
Video OUT
The unauthorized recording, use, distribution, or revision of television programs, videotapes, DVDs, and other materials
is prohibited under Copyright Law, and may subject you to civil and criminal liability.
3M91721A[En] P02-07
To ANT input
on back of TV
To ANT input
on back of TV
TRANSFORMER
(not supplied)
To ANT input
on back of TV
COMBINER
(not supplied)
To ANT input
on back of TV
COMBINER
(not supplied)
TRANSFORMER
(not supplied)
To ANT input
on back of TV
To ANT input
on back of TV
To ANT input
on back of TV
A B
A / B SWITCH
VIDEO 1
VIDEO 2
VIDEO
Rear of TV
AUDIO (R) AUDIO (L)
(not supplied)
7
Combination VHF/UHF antenna (Single 75 ohm cable or 300 ohm
twin-lead wire)
Connect the 75 ohm cable from a combination VHF/UHF antenna to the
antenna jack.
If your combination antenna has a 300 ohm twin-lead wire, use the 300-
75 ohm matching transformer (not supplied).
Combination VHF/UHF antenna (Separate VHF and UHF 300 ohm
twin-leads)
Connect the UHF twin-lead wire to a combiner (not supplied). Connect
the VHF twin-lead to the 300-75 ohm matching transformer (not
supplied). Attach the transformer to the combiner. Attach the combiner
to the antenna jack.
Separate VHF/UHF antennas
Connect the 75 ohm cable from the VHF antenna and the UHF antenna
twin-lead to a combiner (not supplied). Attach the combiner to the
antenna jack.
NOTE: If your VHF antenna has a twin-lead wire, use the 300-75 ohm
matching transformer (not supplied), then connect the transformer to the
combiner.
For subscribers to basic cable TV service
For basic cable service not requiring a converter/descrambler box, con-
nect the Cable TV 75 ohm coaxial cable directly to the antenna jack on
the back of the television.
For subscribers to scrambled cable TV service
If you subscribe to a cable service that requires the use of a converter/
descrambler box, connect the incoming cable to the converter/
descrambler box and connect the output of the box to the antenna jack on
the back of the television. Follow the connections shown at left. Set the
television to the output of the converter/descrambler box (usually channel
3 or 4) and use the converter/descrambler box to select channels.
For subscribers to unscrambled basic cable with scrambled
premium channels
If you subscribe to a cable service in which basic cable channels are
unscrambled and premium channels require the use of a converter/
descrambler box, you may wish to use a two-set signal splitter
(sometimes called a "two-set coupler") and an A/B switch box from the
cable installer or an electronics supply store. Follow the connections
shown at left. With the switch in the "B" position, you can directly tune
any nonscrambled channels on your TV. With the switch in the "A"
position, tune your TV to the output of the converter/descrambler box
(usually channel 3 or 4) and use the box to tune scrambled channels.
This television has an extended tuning range and can tune most cable
channels without using a cable company supplied converter box.
Some cable companies offer "premium pay channels" in which the
signal is scrambled. Descrambling these signals for normal viewing
requires the use of a descrambler device, which is generally provided
by the cable company.
2. To connect the TV to a VIDEO Game
The TV also can be used as a display device for many video games.
However, due to the wide variety of signals generated by these
devices and subsequent hook-up variations required, they have not
all been included in the suggested connection diagrams. You will
need to consult each device's owner's manual for additional
information.
VIDEO Game
OUT
To Audio/Video
(not supplied)
3. To connect the TV to a camcorder
To playback from the camcorder, connect the camcorder to
the TV as shown.
To AV OUT jack
(not supplied)
22/12/05, 4:46 PM
TV
Front of
Front of TV
7