Fortin INT-SL Quick Start Manual

1
Make the connections of the INT-SL to the
vehicle:
1.A
Connector 1 (Black):
Determine the type of installation:
INSTALLATION WITH DATA-LINK
INSTALLATION WITHOUT DATA-LINK
1.B
Connector 2 (White):
Make the connections
Press and hold the programming
2
button. Plug in the
in the INT-SL interface.
The LED will turn on, indicating
3
the beginning of programming.
Plug the
INT-SL interface.
4
WARNING: Connector 2 can be easily
plugged in backwards.
While holding the programming
5
button, turn the key to the ignition
position.
6
The LED will flash rapidly.
7
Release the programming button.
8
Start the vehicle with the key.
9
The LED will turn off.
10
Turn the key OFF.
The interface is programmed.
CHEVROLET Impala
FONCTIONNAL IF EQUIPPED
R
Bypass PK3, Passlock or VATS
R
Doorlock Control
£
Factory Alarm Control (OEM)
R
Trunk Release
£
Door status
WITH DATA-LINK
connector 1
connector 2 into the
WITHOUT DATA-LINK
Connect wire to Remote-Starter/Alarm
Copyright © 2008, FORTIN AUTO RADIO INC
2000-2005
DATA INTERFACE MODULE FOR SECURITY SYSTEM / REMOTE STARTER.
£
Heated Seats and Heated
Mirrors (Heated seats will turn
ON (low power) ONLY if the
engine temp is below 0°C
(32°F) when remote started.)
Lt. Blue
N.C.
White
N.C.
Ignition
Pink
2
Blue
N.C.
Orange
N.C.
Data OBD2
Purple
N.C. Yellow
PIN 2
2
1 2 4 8
3 5 6 7
WARNING: Connector 2 can be easily
plugged in backwards.
9 10 11 12 13 14 15 16
1
Lock
Lt. Blue
Unlock
White
Ignition
Pink
(-) While running
2 Blue
Orange
N.C.
Data OBD2
Purple
Yellow
N.C.
PIN 2
2
1 2 3 4 5 6 7 8
WARNING: Connector 2 can be easily
plugged in backwards.
9 10 11 12 13 14 15 16
1
Cut off one plug of the Data-Link connector, connect the
red wire to +12V and the black wire to ground.
Connect wire to vehicle
Technical support:
TEL: 514-255-HELP (4357)
FAX: 514-255-1367
Web: www.ifar.ca
ALL RIGHTS RESERVED
INT-SL
WEB
Made in Canada - Rev.B 03 / 04 / 2009
UPDATE
W e b s i t e : h t t p : / / w w w . i f a r . c a
£ £
Rear Defrost Start
R £
Parking Light Control Slidding doors
£ R
Retained Accessory Power Tach
£ R
Memory selection Driver 1 and Hand Brake
R
2 (by Unlock) Foot Brake
Lt. Blue/Black
N.C.
White/Black
N.C. In Data-Link mode the analog Input
(unlock, ground out) are disabled for
Pink/Black
N.C.
security.
Green
N.C.
Tach
Orange/Black
~
Starter or alarm
Purple/White or Purple/Black N.C.
Yellow/Black
N.C.
Trunk
Lt. Blue/Black
White/Black
N.C.
Parking Light
Pink/Black
Green
N.C.
Tach
Orange/Black
~
Purple/White or Purple/Black N.C.
Yellow/Black
N.C.
Red +12V
Black
Neither the manufacturer or distributor of this module is
responsible of damages of any kind indirectly or directly
caused by this module, except for the replacement of this
module in case of manufacturing defects. This module must
be install by qualified technician. This instruction guide may
change without notice. Visit www.ifar.ca to get latest version.
Data-Link
Data-Link
Data Link Port
OUTPUT INPUT