Page 1
OPERATION AND PARTS MANUAL MODEL MB25A REBAR BENDER (PORTABLE ELECTRIC) Revision #3 (11/18/08) THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
Tool Box and Tools Assembly ......28-29 Wiring Diagram ............. 30 Terms and Conditions Of Sale — Parts ....31 Specification and part number are subject to change without notice PAGE 2 — MB25A REBAR BENDER • OPERATION AND PARTS MANUAL — REV. #3 (11/18/08)
KEEP bystanders, children, and visitors away while operating the equipment. Distractions can cause loss of control. MB25A REBAR BENDER • OPERATION AND PARTS MANUAL — REV. #3 (11/18/08) — PAGE 5...
Page 6
If they are not, server damage nameplate before applying power. to the unit, particularly to the power cord could occur. Personal injury may also occur. s t l PAGE 6 — MB25A REBAR BENDER • OPERATION AND PARTS MANUAL — REV. #3 (11/18/08)
An emergency button is available to immediately stop the machine when something goes wrong during bending. The roller then returns to the starting position. PAGE 8 — MB25A REBAR BENDER • OPERATION AND PARTS MANUAL — REV. #3 (11/18/08)
12. Handle - Used to lift the rebar bender. 6. Power Switch - Turns the power of the rebar bender on or off. MB25A REBAR BENDER • OPERATION AND PARTS MANUAL — REV. #3 (11/18/08) — PAGE 9...
If the rebar is not parallel to the front, the bending angle will be incorrect. See Figure 3. PAGE 10 — MB25A REBAR BENDER • OPERATION AND PARTS MANUAL — REV. #3 (11/18/08)
Page 11
NEVER stand in water and touch a POWER CORD live power cord. (POWER ON) MB25A REBAR BENDER • OPERATION AND PARTS MANUAL — REV. #3 (11/18/08) — PAGE 11...
Figure 8. Carbon Brush Size 1. Make sure that the power plug is not connected to the power source. CARBON BRUSH CAP Figure 9. Replacing Carbon Brushes PAGE 12 — MB25A REBAR BENDER • OPERATION AND PARTS MANUAL — REV. #3 (11/18/08)
Page 13
. r o i f f e i c . t n t l o a t l MB25A REBAR BENDER • OPERATION AND PARTS MANUAL — REV. #3 (11/18/08) — PAGE 13...
A blank entry generally indicates that the item is not sold separately or is not sold by Multiquip. Other entries will be clarified in the “Remarks” Column. PAGE 14 — MB25A REBAR BENDER • OPERATION AND PARTS MANUAL — REV. #3 (11/18/08)
SERI A L NO. RIGHT WRONG * Position the stopper (A) so that the rebar (B) to be bent is parallel to the front of stopper PAGE 16 — MB25A REBAR BENDER • OPERATION AND PARTS MANUAL — REV. #3 (11/18/08)
Page 17
NAMEPLATE ............1 ..CONTACT MQ PARTS DEPT. 8010750 ROLLER AND COLLAR DECAL 8005070 STOPPER INSTALLATION DECAL 8010770 ROLLER AND COLLAR INSTALLATION DECAL 1 8010760 ROLLER, COLLAR, AND TOOLS DECAL MB25A REBAR BENDER • OPERATION AND PARTS MANUAL — REV. #3 (11/18/08) — PAGE 17...
MB25A — HOUSING ASSEMBLY HOUSING ASSEMBLY NOTES: INCLUDED WITH ITEM 109 2 INCLUDED WITH ITEM 110 INCLUDED WITH ITEM 115 INCLUDED WITH ITEM 117 PAGE 24 — MB25A REBAR BENDER • OPERATION AND PARTS MANUAL — REV. #3 (11/18/08)
Page 25
M5SNR25S00 SNAP RING STW 25 7513050 ALLEN HEAD SCREW 6X25 7538020 SCREW W/ LOCK WASHER XR 3X18 6200190 MICRO SWITCH 4600100 MICRO SWITCH HOLDER PLATE MB25A REBAR BENDER • OPERATION AND PARTS MANUAL — REV. #3 (11/18/08) — PAGE 25...
Page 26
MB25A — HOUSING ASSEMBLY HOUSING ASSEMBLY NOTES: INCLUDED WITH ITEM 109 2 INCLUDED WITH ITEM 110 INCLUDED WITH ITEM 115 INCLUDED WITH ITEM 117 PAGE 26 — MB25A REBAR BENDER • OPERATION AND PARTS MANUAL — REV. #3 (11/18/08)
Page 27
COLLAR FOR END PLATE 6301010 CORD WITH PLUG 6600030 CLAMP, CABLE 7538030 SCREW W/ LOCK WASHER XR 4X6 C5Y8411000 STRAIN RELIEF, CABLE 9002120 FOOT SWITCH ASSEMBLY MB25A REBAR BENDER • OPERATION AND PARTS MANUAL — REV. #3 (11/18/08) — PAGE 27...
Micro Switch Black White Light Black Brown Dark Blue Blue A2/b White Black Rotary Switch Black White Gray Black Black Black Black Magnet Clutch Motor PAGE 30 — MB25A REBAR BENDER • OPERATION AND PARTS MANUAL — REV. #3 (11/18/08)