1. Manuals
  2. Brands
  3. PCB Manuals
  4. Industrial Equipment
  5. 1403-05ADB
  6. Installation and operating manual

PCB 1403-05ADB Installation And Operating Manual

Fatigue rated low profile load cell, dual bridge
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Model 1403-05ADB
FATIGUE RATED LOW PROFILE LOAD CELL, DUAL BRIDGE
Installation and Operating Manual
For assistance with the operation of this product,contact:
PCB Load & Torque, Inc.
Toll-free: 866-684-7107
24-hour SensorLine™: 716-684-0001
Fax: 248-888-8266
E-mail: LTInfo@pcbloadtorque.com
Web: www.pcbLoadTorque.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 1403-05ADB and is the answer not in the manual?

Questions and answers

Related Manuals for PCB 1403-05ADB

Summary of Contents for PCB 1403-05ADB

  • Page 1 Model 1403-05ADB FATIGUE RATED LOW PROFILE LOAD CELL, DUAL BRIDGE Installation and Operating Manual For assistance with the operation of this product,contact: PCB Load & Torque, Inc. Toll-free: 866-684-7107 24-hour SensorLine™: 716-684-0001 Fax: 248-888-8266 E-mail: LTInfo@pcbloadtorque.com Web: www.pcbLoadTorque.com...
  • Page 2 Equipment calibration reason, you are not completely satisfied cycles are typically established by the with any PCB product, PCB will repair, users own quality regimen. When in replace, or exchange it at no charge. You doubt about a calibration cycle, a good may also choose to have your purchase “rule of thumb”...
  • Page 3 Materials Authorization (RMA) PCB for a complete statement of our Number. This RMA number should be warranty. Expendable items, such as clearly marked on the outside of all batteries and mounting hardware, are not package(s) and on the packing list(s) covered warranty.

  • Page 4: Table Of Contents

    11.2 Electrical Trouble Shooting ......................8 11.2.1 Estimating Bridge Balance using an Ohm Meter ..............8 12.0 CALIBRATION / REPAIR SERVICES ................8 12.1 RMA / Purchase Order........................9 13.0 WARRANTY ........................9 PCB Load & Torque, Inc. Toll-Free in USA 866-684-7107 716-684-0001 www.pcbloadtorque.com...

  • Page 5: Introduction

    3.1 Dimensions 1.0 INTRODUCTION The following figure and table give the general outline Dual bridge fatigue-rated load cells manufactured by PCB dimensions of the dual bridge fatigue-rated load cells. Load and Torque, Inc. are guaranteed to last 100 million fully reversed cycles (full tension through full compression).

  • Page 6: Standard Components

    25%, 50% and finally 100% of the NOTE: Pre-tension studs include the threaded stud and the required torque being applied. jam nut. PCB Load & Torque, Inc. Toll-Free in USA 866-684-7107 716-684-0001 www.pcbloadtorque.com...

  • Page 7: Threaded Tension Rods

    #4-40 x 3/8” Socket Head Cap Screw Figure 7 - Remove the #4-40 x 1/4” Figure 8 - Slide the Connector Button Head Cap Screws Protector (54823-02) Behind the Connector PCB Load & Torque, Inc. Toll-Free in USA 866-684-7107 716-684-0001 www.pcbloadtorque.com...

  • Page 8: Electrical Installation

    + Signal Green 6.0 CALIBRATION + Excitation Red Every dual bridge fatigue-rated load cell purchased from PCB Figure 11 - Western Regional Strain Gage Committee Wiring Code Load & Torque, Inc. has been fully calibrated per ISO/IEC 17025 procedures, and meets all published specifications.

  • Page 9: Measured Output

    14. The maximum shear stress measured by the bonded strain to minimum load. gages is less than 40% of the endurance limit shear stress for alloy steel and 48% for aluminum. PCB Load & Torque, Inc. Toll-Free in USA 866-684-7107 716-684-0001 www.pcbloadtorque.com...

  • Page 10: Shunt Calibration Description

    –P on them. Never use a pressure washer on the load cells. connector leads. PCB Load & Torque, Inc. Toll-Free in USA 866-684-7107 716-684-0001 www.pcbloadtorque.com...

  • Page 11: Trouble Shooting

    12.0 CALIBRATION / REPAIR SERVICES conductors for short circuits. Check isolation resistance, load cell flexure to PCB Load & Torque offers calibration and repair services. conductors. The PCB Calibration Laboratory in Farmington Hills, Michigan is A2LA Accredited per ISO/IEC 17025.

  • Page 12: Rma / Purchase Order

    (SEB) calculations and entries abilities and traceability statements. If an initial evaluation shows that a transducer requires repair, PCB will provide the customer with an estimate prior to taking any corrective action. 12.1 RMA / Purchase Order Please request a return material authorization (RMA) before sending a load cell back to the factory for any reason.
  • Page 13 2.9 Kg Mounting Thread 5/8 - 18 UNF-3B No Metric Equivalent Sensing Element Strain Gage Strain Gage PCB Load & Torque, Inc. Mounting Torque 200 in-lb 23 Nm 24350 Indoplex Circle Deflection at Full Scale Capacity 0.001 in 0.03 mm...
  • Page 14 PCB Load & Torque Inc. claims proprietary rights in REVISIONS the information disclosed hereon. Neither it nor any reproduction thereof will be disclosed to others without DESCRIPTION the written consent of PCB Load and Torque Inc. ADD FIELD NOTE 2 35193 22.5°...

Table of Contents