Page 9
Foreword Read the following instructions, including the warranty terms before installing and using the appliance. Visit our website www.electroluxprofessional.com and open the Support section to: Register your product Get hints & tips of your product, service and repair information The installation, use and maintenance manual (hereinafter Manual) provides the user with information necessary for correct and safe use of the appliance.
Constructional modifications ......................23 E.15 Installation of rack handling systems ....................23 E.16 Arrangement for mechanical connection (only for Electrolux Professional rack handling system non motor operated) ..........................23 E.17 Installation of the end limit switch ....................24 E.17.1 Prearrangement for electrical connection ................24 E.18...
SAFETY INFORMATION General information These appliance is intended to be used for commercial applications, for example in kitchens of restaurant, canteens, hospitals. It must be used for washing or drying (depending on the model) plates, dishes, glassware, cutlery and similar articles. To ensure safe use of the appliance and a proper understanding of the manual it is necessary to be familiar with the terms and typographical conventions used in the documentation.
• Do not remove or tamper with the machine’s safety devices. • Before carrying out any machine installation, always consult the installation manual, which gives the correct procedures and contains important information on safety. • Unauthorized personnel must not enter the work area. •...
Transport, handling and storage • Due to their size, the machines cannot be stacked on top of each other during transport, handling and storage; this eliminates any risks of loads tipping over due to stacking. • Do not stand under suspended loads during loading or unloading operations. Unauthorized personnel must not enter the work area.
Risk a combination of probabilities and risks of port personnel. injury or harm to health in a hazardous Manufacturer Electrolux Professional SpA or any other situation. service centre authorised by Electrolux Professional SpA.
8.5 kW against risks. Guard an element of a machine used in a specific Electrolux Professional spa - Viale Treviso, 15 - 33170 Pordenone (Italy) way to provide protection by means of a physical barrier. Safety device a device (other than a guard) that elimi- nates or reduces the risk;...
For requests or for Electrolux Professional SpA company. further information, contact Electrolux Professional S.p.A. - Via Treviso, 15 - 33170 Pordenone - Italy. Keeping the manual The manual must be carefully kept for the entire life of the appliance, until scrapping.
The Manufacturer provides for the possibility of connecting the drying tunnel only to rack-type dishwashers included in the Make sure that the switch disconnector of the Electrolux Professional SpA catalogue. machine is locked in the Off position - “O“. Characteristics of the place of machine...
• This space must be increased in case of use and/or transfer of other equipment and/or means or if exit routes are necessary inside the workplace. CAUTION • Install the machine at a distance of not less than 50 mm from the wall so as not to affect correct ventilation of internal components.
(e. g. glasses in case of risk of flying splinters during drilling). • Install only Electrolux Professional rack handling system (non-motor-operated). NOTE! To install the drying tunnel in a left to right machine, refer to the corresponding instructions provided.
6. Install the drain in the dryer to discharge the residual water. 9. Refit the side panels “1-2“ on the drying tunnel side. 7. Connect the drain outlet of the dryer and the machine with E.11 Drying tunnel corner 90° the supplied connection hose.
Page 21
1. Install the adjustable feet on the dryer. Place the dryer on 4. Remove the top panel from the drying tunnel to make the turntable and fix it with the self tapping screws. easier the operations. 2. Install the side and top brackets on the machine. 5.
7. Join the roofs of the two modules. Fitting the top bracket • Take the coil of wiring cables located in the top part of the on the ⌀=5 mm stud bolts and firmly secure it with ⌀=5 mm drying module and pass it along the top of the dishwasher to flange nuts.
1. Remove the vent(s) from the machine, if present. You can see 2 holes in the left and 2 holes in right side of the machine panels. It is available for this purpose recommended silicone by Electrolux Professional. You can order it with this reference code 059611.
Drying Tunnel 90° End Limit Switch CAUTION Make sure that there are not any water leakages. E.17 Installation of the end limit switch IMPORTANT Install only Electrolux End Limit Switch. Drying Tunnel 22″ End Limit Switch E.17.1 Prearrangement for electrical connection The machine is pre-configured for the installation of end limit switch.
such systems emergency switches that are clearly visible and 3. connect the emergency switches to: identifiable and easily accessed by the operator “R“ who must Emegency switch IN use them. Described below are possible couplings of dishwashers “L“ • XT2–3BEL and XT2–3AB terminal blocks with rack handling systems “M“, with the corresponding positions of the emergency switches “E“...
E.20 Fitting curtains Types of curtains With the machine switched off and cold, fit or refit the curtains Double long Double long for drying as illustrated below. tunnel 90° Drying Tunnel 22″ Left to right Fasten the curtains with the flat part against the hook Right to left Drying Tunnel 90°...
Positioning and fitting of the curtains 5. The display shows all the available options to select the right type of the dryer. Make sure all the types of curtains, provided with the machine, are correctly fitted according to that indicated in paragraph “E.20 Fitting curtains“.
Need help?
Do you have a question about the 534411 and is the answer not in the manual?
Questions and answers