Advertisement

Quick Links

FLEET
SERIES SINK
PRODUCT INSTRUCTIONS
NOTE: We recommend reading through the entire Assembly Instructions prior to proceeding with use, service or maintenance.
Page 1 of 16
September 2023

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FLEET FS3-0026 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for PolyJohn FLEET FS3-0026

  • Page 1 FLEET SERIES SINK ™ PRODUCT INSTRUCTIONS NOTE: We recommend reading through the entire Assembly Instructions prior to proceeding with use, service or maintenance. Page 1 of 16 September 2023...
  • Page 2: Product Specifications

    PRODUCT SPECIFICATIONS FLEET SERIES SINK FS3-0026 DIMENSION IMPERIAL METRIC Height 39 in. 100 cm Width 17 in. 43 cm Depth 21 in. 53 cm Tank Capacity 20 gal 76 liter. Pump Capacity (per stroke) 2 fl. oz 59. 1 4 ml Number of Single Dispenses 1280 1280...
  • Page 3: Tools Required For Assembly

    TOOLS REQUIRED FOR ASSEMBLY FLEET SERIES SINK FS3-0026 Phillips Screwdriver Drill 13/64” (5.33mm) 1-1/8” (29mm) Drill Bit Hole Saw Tape Measure Rivet Gun FULL SIZE SCALE FASTENER DRAWINGS (2) PC-000106 (2) PC-000103 - Rivet (1) PC-000158 Back-up Washer Large Flange Self Tapping Screw Page 3 of 16 September 2023...
  • Page 4: Product Overview

    PRODUCT OVERVIEW FLEET SERIES SINK FS3-0026 These self-contained hand wash sinks have been engineered with a larger bowl so users may wash up to their elbows. Designed for either Flushing or Non-Flushing FS3 Fleet Series Portable Restrooms. Sinks are supplied fully assembled including all fasteners for installation.
  • Page 5: Operation

    REPLACEMENT INSTALLATION FLEET SERIES SINK FS3-0026 FOR FLUSHING UNITS Remove Existing Sink - Carefully lay the unit on its back and disconnect the intake hose from the pump and the hose going to the bottom of the waste tank. Stand the unit back upright. NOTE: Sinks for flushing units are supplied with the required hoses attached.
  • Page 6 INSTALLATION FOR FLEET SERIES SINK FS3-0026 NON-FLUSHING UNITS Locate the drill spot on the top right surface of the waste tank. Use a 1-1/8” hole saw and cut the drain hole. Position the sink so the drain pipe nipple is inserted into the hole. Insert drain hose into tank (Refer to the illustration below) Drill two 13/64”...
  • Page 7 / / www. p ol y j o hn. c om/pc- 0 00111 **NOT SHOWN PC-000782 Decal Not for Drinking http://www.polyjohn.com/pc-000782 PC-000783 Decal Transport http: / /www.polyjohn.com/pc-000783 PC-000790 Decal Foot Pump http://www.polyjohn.com/pc-000790 PC-000418 http: / /www. p ol y j o hn. c om/pc-000418 1” Uniseal PC-100421B http://www.polyjohn.com/pc-100421b...
  • Page 8: Parts Diagram

    PARTS DIAGRAM FLEET SERIES SINK FS3-0026 tank assembly & tube not installed on FS3-0026*C (static) 3-way Valve ONLY ON FLUSHING RECIRC MODELS FS3-0026*F FS3-0028 http://www.polyjohn.com/fs3-0028 Anti-Siphon Tank Assembly **See tank diagram** PC-000415 http://www.polyjohn.com/pc-000415 1/4” Uniseal CT38-046 http://www.polyjohn.com/ct38-046 Tube (pump to tap) CT38-0065 http://www.polyjohn.com/ct38-0065...
  • Page 9 FS3-0028 http://www.polyjohn.com/fs3-0028 Anti-Siphon Tank PC-000900 - Elbow http://www.polyjohn.com/pc-000900 PC-000352 http://www.polyjohn.com/pc-000352 Hose Clamp #12 CT38-035 - Tube http: / /www.polyjohn.com/ct38-035 (Intake to Anti-Siphon) CH100-028 Hose 1” x 28” (2) PC-000417 http://www.polyjohn.com/pc-000417 3/4” Uniseal CH100-025 http://www.polyjohn.com/ch100-025 PC-000415 http://www.polyjohn.com/pc-000415 Hose 1” x 25”’...
  • Page 10 PARTS DIAGRAM FLEET SERIES SINK FS3-0026 RECIRC HOSE CONNECTIONS RECIRC Flush Hose Connections with 3-Way Valve Installed. Sink Bowl Drain Hose Into Waste Tank Pump Outlet to Flush Bowl 3-way Outlet to Pump Inlet #1 Recirc Filter to Pump Inlet #2 ** CHECK FOR LEAKS AT FOOT PUMP CONNECTIONS ** Page 10 of 16...
  • Page 11 FLEET SERIES SINK FS3-0026 Sink Tube Connections. Sink Pump Outlet to Sink Tap Sink Tank to Anti-Siphon Tank Sink Tank to Sink Pump Inlet Page 11 of 16 September 2023...
  • Page 12: Cleaning And Maintenance

    WHITING, IN 46394-2175 800-292-1305 www.polyjohn.com/supplies/pros-choice.html We highly recommend membership in the Portable Sanitation Association International (PSAI); the worldwide authority on portable sanitation services. The PSAI, “Portable Sanitation Industry Certification Program” manual contains a wealth of information on standards and service procedures.
  • Page 13 Chemical exposure typically occurs through inhalation, ingestion, or adsorption. PolyJohn products are not intended to be used in these methods. PolyJohn Corporation cannot foresee all uses of their products (both intended and unintended uses) and as a result has opted to provide a general warning of known chemical presence.
  • Page 14: Frequently Asked Questions

    That being said, there is always a very small chance that there is a manufacturing defect. If all other options have been ruled out, then please visit the PolyJohn Warranty page. Q: Where is the fill port? A: Most of our sinks fill ports are colored blue to indicate fresh water.
  • Page 15: Warranty Disclaimer

    PolyJohn Enterprises warrants our sinks, tanks, trailers and sanistands from the date of purchase. Any misuse or abuse of our products or failure to properly follow recommended procedures shall void this warranty. The warranty is a 1 year limited warranty and a 90 day limited warranty for components thereof.
  • Page 16 SERIES SINK FS3-0026 “PolyJohn is a family owned, state of the art, plastics manufacturing company dedicated to providing its employees with a work environment committed to excellence, and its customers with innovative products, services and technology that meet or exceed their requirements.”...

Table of Contents