Table of Contents
Advertisement
speed while pressing the MANUAL
button ( P ).
2. When the stylus reaches the desired place on the record,
release the MANUAL
button ( ¢ or p> ), and the tone-
arm will lower itself onto the record surface and play
will start,
HOW TO USE GAUGES
Read the disc gauge that corresponds to the desired loca-
tion on the disc first, and then move
the tonearm to the
corresponding position on the gauge.
STYLUS REPLACEMENT
(1) Remove
the stylus from the cartridge by holding it be-
tween
the fingers and
pulling
off to the direction as
shown on Fig. 18.
(2) When
replacing a new stylus, carefully insert the stylus
into the cartridge and fix the stylus on the cartridge.
*
Switching the power supply off after moving the tone-
arm
slightly
to the left makes
it easier to change the
needle,
REPEAT PLAY (Fig. 19)
Press the repeat button to hear the same record repeatedly.
The repeat indicator will tight and when
play is finished,
the tonearm
will
lift, return
to the outer groove of the
.continue to be repeated as long as the repeat indicator is
illuminated.
To cancel play-repeat, press the repeat button
again.
Play-repeat
will
also
be cancelled
when
play
is
stopped by pressing the stop button.
@
Do not operate REPEAT
play for 10° (25 cm) records,
@
Cause
the tonearm
to return
to the tonearm
rest by
operating the MANUAL
( P
) control. After this, use
the MANUAL
( €
) control to start playing the record.
Remember that no repeat play function is available.
LISTENING
TO BROADCAST
Push the power
switch
to the ON
position. (After approxi-
mately five seconds,
a BEEP sound can be heard. After this,
the following operations should be performed.) (Fig. 20)
Press the FM, MW or LW button.
MANUAL TUNING
Depress either the MANUAL
{ B®
) or MANUAL
( <4 )
until
the frequency of the desired station appears
in the
FREQUENCY
display (29).
The FREQUENCY
display is changed
in 50 kHz steps in
the FM
band and in 9 kHz steps in the MW and LW band
each time the MANUAL
( <
) or MANUAL
( P ) de-
pressed. The frequency display will change constantly while
either MANUAL
( <<
) (B® ) is depressed. When the fre-
quency
of the desired
station
is approached,
release the
control
and
then adjust the frequency
by pressing
it in
single push control operations.
AUTO TUNING
By depressing the AUTO (>) or AUTO (<)}, the frequency
automatically changes upwards or downwards and stops at
the next
available
broadcast station. With a weak
broad-
cast
station,
the
tuner
may
not stop.
For
reception
of
such a station, follow the steps described in the paragraph
"MANUAL
TUNING".
@
Do
not select any other functions during auto tuning
(while
frequency
is being
varied).
When
tuner
has
again
being selected, it may
happen
that normal
ope-
ration can not be obtained.
PRESET TUNING
1. Tune
to
the frequency
of the desired
broadcasting
station by manual or auto tuning method.
2. Press
the
MEMORY
button
(31), The
corresponding
MEMORY
indicator (30) will light up.
3. The MEMORY
indicator (30) will remain on for only a
short time (about 4 seconds).
During this period, press one of the PRESET buttons (13).
That
completes
the presetting
operation
for that station.
The remaining 6 channels may
be used for presetting an-
other 6 stations, (MW; 4 stations, LW; 3 stations)
After completing the presetting operation, any of the preset
stations may be tuned automatically by a single push of the
relevant PRESET
button
(13). The selected preset station
will be indicated by address indicator (28).
This presetting operation
may be repeated any number of
times.
{f a station which
has been preset is no longer re-
quired and a new station is preferred, simply tune to the
new station and preset it in the relevant channel according
to the method
described above. The previous station will
be erased automatically and replaced by the new one.
Select the desired volume level with the VOLUME
control.
The volume
of the left-side and right-side speakers can be
adjusted by means of the BALANCE control.
(Fig, 21)
TAPE DECK PLAYBACK
Push the power switch to the ON position. (After approxi-
mately five seconds,
a BEEP sound can be heard. After this,
the following operations should be performed.)
Then insert the cassette tape directing the side (A orB) you
wish to hear toward you with the tape side downward.
(Fig, 22)
Set the DOLBY
NR switch so as to match the tape to be
* played. That is, set it to the IN position for tapes recorded
with the DOLBY
NR system, and to the OUT position for
tapes recorded without DOLBY
NR. (Fig. 23)
Start playback by pushing the TAPE button. (Fig, 24)
Select the desired volume with the VOLUME
control.
(Fig. 25)
HOW TO USE MSS
MSS
(Music Select Sensor) can be used usefully when you
want
to listen to next music or the same
music just being
played while playing back a music prerecorded tape.
Press the AUTO
(>)
button
when
you want to listen to
the music
immediately
after that being played back now.
The
tape
is fast-forward
until
the beginning of the next
music, and then the playback will start automatically.
Press the AUTO
( <) button when
you want to listen to
the same
music
being played again. The tape is rewound to
the beginning of the music, and its playback
will resume
automatically.
NOTE:
MSS does not operate on the following tapes.
@
Tapes on which voice does not continue, such as conver-
sation, etc.
Advertisement
Table of Contents
