Adjust The Volume - Technics SC-DV250 Operating Instructions Manual

Basic operations Pe
i ROTS948
Refer to the illustration on page 15 of the illustrated booklet.
Ec 22]
Preparation
Turn on the television and select the appropriate video input on the televi-
sion to suit the connections for the player.
1 Press DIRECT OPEN [DISC 1]-[DISC 5] to opena
tray and set a disc.
Label must face upward. (With double-sided discs, load so the label
for the side you want to play is facing up.)
2 Press [4, OPEN/CLOSE] to close the tray.
The tray closed is in the play position (its disc indicator turns green)
When you insert CDs and Video CDs, the tuner/amplifier display shows the
total number of tracks and total playing time if "DVD" is selected as the
source.
Some discs start playing automatically.
Repeat steps 1 and 2 to load the other trays.
3 Press [DISC, 1-5] to change the play position tray
and start play.
The type of disc (DVD/VCD/CD) in the play position is displayed on
the tuner/amplifier.
Adjust the volume.
4
Play position
The disc in the play position is ready to play immediately when you press
[I>],
To stop the disc
Press [I]. The "l>" indicator flashes orange to indicate that the resume
function is on. (See right.)
To pause play
Press [18] during play. The "" indicator flashes green.
Press [L>] to resume play.
Note on CD-R and CD-RW
This unit can play CD-DA and video CD format audio CD-R and
CD-RW that have been finalized* upon completion of recording. It
may not be able to play some CO-R or CD-RW due to the condition
of the recording.
"Finalizing is a process that enables CD-R/CD-RW players to play
audio CD-R and CD-RW.
elf "Q" appears on the television
The operation is prohibited by the unit or disc.
*The disc continues to rotate while the menu is displayed even after you
finish playing an item. Press [lil] when you finish to preserve the unit's
motor and your television screen.
®Volume may be lower when playing DVDs than when playing other discs
or during television broadcasts.
if you turn the volume up on the television or amplifier, ensure you reduce
the volume again before playing other sources so that a sudden increase
in output does not occur.
Refer to illustrations BJ and [Jj on page 17 of the illustrated booklet.
EJ wren amenu screen appears on the television
buco
Remote control on!
Press the numbered buttons to select an item.
To select title No.10 or over, press [2 10/-/--] then the two digits.
e.g. Title No. 12: [210A]: >[1]- >(2]
e@When playing DVDs, you can also use {A, ¥, «, ®] to select items.
Press [ENTER] to confirm your selection
Play of the selected item now begins.
Other buttons used to operate menus
Read the disc's instructions for further details about operation.
To return to a
menu during play
DVD: [MENU] or [TOP MENU]
Video CD: [RETURN]
To show the next
or previous menu
[SKIP >] (next menu)
[44 SKIP] (previous menu)
DVD menus
DVDs can have several menus. The menu displayed when you press [TOP
MENU] may be different from the menu displayed when you press [MENU].
Title Title : Title
The dise's y
top menu
T T
Menu ; Menu : |
| Menu i
MENU
TOP MENU
E Resume-functio
fue [eb
If you press [3] during play, the unit remembers the position.
The play indicator flashes to indicate that the resume function is active.
This function does not work if the disc's play time is not displayed on the
tuner/amplifier.
To restart play from the point
While the play indicator is flashing, press [>].
Play resumes from the point it was stopped
With DVD
"Press PLAY to Chapter Review' appears on the TV screen for a few sec-
onds. If you press [[>] while the message is on the screen, the beginning
portions of each chapter up to the current one are played. Full play
resumes from the point where you stopped play.
To cancel the resume function
Press [ll].
Resume is canceled if the disc tray is opened or if you change discs,
The position is saved even if the unit is turned off or a source other than
"DVD" is selected.
Chapter review is not possible with some DVDs.