Advertisement
Advertisement
Table of Contents
Related Manuals for Broyhill 1926FM-23-413
Summary of Contents for Broyhill 1926FM-23-413
-
Page 3: Safety Information
GENERAL BEST PRACTICES FOR ASSEMBLY: Read all instructions before starting Clear a large flat area to begin assembly Some steps may require a helper Hardware required is provided for each step Pay attention to orientation SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product. This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC rules. - Page 4 SAFETY INFORMATION (CONT’D) • This product is intended to fit most plasma and LCD televisions (up to 55 inches and weighing a maximum of 70 pounds). Using this item with loads heavier than the stated maximum can result in tipping and/or instability, which can result in injury or even death.
- Page 5 SAFETY INFORMATION (CONT’D) where it may fall into a bathtub or other water container. • To disconnect this appliance, turn controls to the OFF position, then remove plug from outlet. • ONLY connect to properly grounded outlets. • This appliance, when installed, must be electrically grounded in accordance with local codes, with the current CSA C22.1 Canadian Electrical Code or follow U.S.A.
-
Page 6: Parts List
PARTS LIST Left Wall Right Wall Face Frame Opening Plate Upper Opening Plate Heater Top Panel Fireplace Brick Wall Fireplace Glass Front Base And Heater Fire Log Fireplace Grate Remote Control (Battery Inside) -
Page 7: Hardware List
HARDWARE LIST Ø1/4”*1-1/4” 19D*1.5mm Ø8*30mmL Bolt Washer Wooden Dowel Ø5/32”*1-1/8” Ø7*12mmL Small Bolt Screw Touch-up Pen Allen Wrench PREPARATION Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. Estimated Assembly Time: 45 minutes. - Page 8 STEP 1 Insert four wooden dowels (CC) into the holes on the base and heater (J). Align the right wall (C) with the inserted wooden dowels and lower into place. Secure the right wall (C) to the base and heater (J) with two washer (BB) and two bolts (AA) using the Allen Wrench provided (GG) as shown in the diagram.
- Page 9 STEP 2 Insert six wooden dowels (CC) into the holes on the face frame (D). Align the holes on the face frame (D) with the corresponding holes on the left wall (B) and right wall (C). Secure the face frame (D) in place with four washers (BB) and four bolts (AA) using the Allen Wrench provided (GG) as shown in the diagram.
- Page 10 STEP 3 Insert four wooden dowels (CC) into the bottom holes of the upper opening plate (F), align and attach the upper opening plate (F) to the opening plates (E). Secure the opening plates (E) to the upper opening plate (F) with two washers (BB) and two bolts (AA) using the Allen Wrench provided (GG) as shown in the diagram.
- Page 11 STEP 4 Insert four wooden dowels (CC) into the holes on the base and heater (J). Align the assembled panels from step 3 with the inserted wooden dowels (CC) and lower into place as shown in the diagram. Assembled View: Ø8*30mmL Wooden Dowel...
- Page 12 STEP 5 Align the holes in the assembled panels from step 3 with the holes in the face frame (D) and secure the panels together with nine washers (BB) and nine bolts (AA) using the Allen Wrench provided (GG) as shown in the diagram. Fully tighen bolts.
- Page 13 STEP 6 Align the holes in the assembled panels with the holes in the top (A) and secure from underneath with six washers (BB) and six bolts (AA) using the Allen Wrench provided (GG) as shown in the diagram. Fully tighten bolts. Assembled View: Ø1/4”*1-1/4”...
- Page 14 STEP 7 From behind the assembly, attach the fireplace glass front (I) by carefully lowering it into the front groove on the base and heater (J). Secure the glass by turning the pre-assembled plastic knobs. Assembled View:...
- Page 15 STEP 8 Position the fireplace grate (N) by inserting the bottom pins of the fireplace grate (N) into the holes on the base and heater (J). Secure the fireplace grate (N) in place by tightening two small bolts (DD) with a Phillips screwdriver. Attach the USB cable from the heater to the USB port behind the fireplace grate (N).
- Page 16 STEP 9 Remove the film from the adhesive on the top of the fireplace grate (N) and place the fire log (M) on the center of the fireplace grate (N). Assembled View:...
- Page 17 STEP 10 Unfold the fireplace brick wall (H) and brackets. Assembled View:...
- Page 18 STEP 11 Insert the fireplace brick wall (H) into the mantel, slotting it into the grooves on the base and heater (J). Secure it by placing two screws (EE) into the bracket. “Phillips screwdriver not included” Assembled View: Ø7*12mmL Screw “not included”...
- Page 19 STEP 12 Place the heater top panel (G) on top of the firebox with corner bumpers facing inward. Assembled View:...
- Page 20 STEP 13 NOTE: Use the pre-assembled levelers on the base of the fireplace to level the unit. Twist the levelers counter-clockwise to increase the height, twist clockwise to decrease the height. Assembly is now complete. With the help of another person, move the assembly to the final desired location. Once in final position you may plug the heater into the power outlet.
- Page 21 Use with heavier televisions may result instability causing tip over resulting in death or serious injury. FITS UP TO MOST 139.7 cm / 55 in FLAT PANEL TVS MAXIMUM LOAD 31.75 kg / 70 lb SKU#810617767/ITEM#1926FM-23-413 DISTRIBUTION: Greentouch Home Limited ADDRESS: Room 4007, Central Plaza, 18 Harbour Road,Wanchai, Hong Kong...
- Page 22 OPERATING INSTRUCTIONS Control Panel Remote Control To use the remote control, first remove the plastic tab by gently pulling it out of remote control. Controls and Display The control panel will display the heater setting when the unit power is turned ON. Whichever control icon you press will display the current setting of the corresponding function.
-
Page 23: Memory Function
OPERATING INSTRUCTIONS (CONT’D) Heater Function (Control Panel Only) • Press the HEATER ICON to display the current heater setting. • Press the HEATER ICON again to scroll down through the heater settings. Note: Long-hold the icon to quickly scroll through settings. •... -
Page 24: Care And Maintenance
CARE AND MAINTENANCE • Make sure the unit is turned OFF, unplugged and the heating elements of heater are cool whenever you are cleaning the heater or fireplace. • Clean the metal trim using a water-dampened soft, clean cloth. DO NOT use brass polish or household cleaners as these products will damage the metal trim. -
Page 25: Troubleshooting
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Error E1 displayed The overheat sensor has Unplug unit, wait 15-20 minutes, then the sensor will reset on control panel. been engaged. itself. Plug the unit back in and turn on the heater. If the problem persists, call customer service. -
Page 26: One-Year Limited Warranty
ONE-YEAR LIMITED WARRANTY The manufacturer warrants that your new electric fireplace is free from manufacturing and material defects for a period of one year from date of purchase, subject to the following conditions and limitations. Install and operate this electric fireplace in accordance with the installation and operating instructions furnished with the product at all times. -
Page 27: Replacement Parts List
PART DESCRIPTION PART # Fireplace Glass Front 1926FM-23-GLASS FRONT Fire Log FIRE LOG 1 Fireplace Grate GRATE A Remote Control RC-HE85EL02 Heater-black KDI-02-26-M Touch-up Pen OX-0180Y KD Hardware Pack 1926FM-23-413-HARDWARE PACK Glass Clips GLASS CLIPS Leveler T-1007 Printed in Vietnam...
Need help?
Do you have a question about the 1926FM-23-413 and is the answer not in the manual?
Questions and answers