While Operating; Safety And International Symbols; Other Safety Warnings; Rules For Safe Operation - Craftsman 316.79194 Operator's Manual

WHILE OPERATING

• Never start or run the unit inside a closed room or building.
Breathing exhaust fumes can be fatal. Operate this unit only in a
well-ventilated outdoor area.
• Wear safety glasses or goggles that meet ANSI Z87.1–1989 standards
and are marked as such. Wear ear/hearing protection when operating
this unit. Wear a face or dust mask if the operation is dusty.
• Wear heavy long pants, boots, gloves and a long sleeve shirt. Do
not wear loose clothing, jewelry, short pants, sandals or go
barefoot. Secure hair above shoulder level.
• The cutting attachment shield must always be in place while
operating the unit as a trimmer. Do not operate unit without both
trimming lines extended, and the proper line installed. Do not
extend the trimming line beyond the length of the shield.
• This unit has a clutch. The cutting attachment remains stationary
when the engine is idling. If it does not, take the unit to a Sears or
other qualified service dealer for an adjustment.
• Adjust the D-handle to your size in order to provide the best grip.
• Be sure the cutting attachment is not in contact with anything
before starting the unit.
• Use the unit only in daylight or good artificial light.
• Avoid accidental starting. Be in the starting position whenever pulling
the starter rope. The operator and unit must be in a stable position
while starting. Refer to Starting/Stopping Instructions.
• Use the right tool. Only use this tool for its intended purpose.
• Do not overreach. Always keep proper footing and balance.
• Always hold the unit with both hands when operating. Keep a
firm grip on both handles or grips.
• Keep hands, face, and feet at a distance from all moving parts. Do not
touch or try to stop the cutting attachment when it rotates.
• Do not touch the engine, gear housing or muffler. These parts get
extremely hot from operation, even after the unit is turned off.
This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's
manual for complete safety, assembly, operating and maintenance and repair information.
SYMBOL MEANING
• SAFETY ALERT SYMBOL
Indicates danger, warning or caution. May
be used in conjunction with other symbols or
pictographs.
• READ OPERATOR'S MANUAL
WARNING:
and follow all warnings and safety instructions.
Failure to do so can result in serious injury to the
operator and/or bystanders.
• WEAR EYE AND HEARING PROTECTION
WARNING:
can cause severe eye injury and hearing loss.
Wear eye protection meeting ANSI Z87.1–1989
standards and ear protection when operating
this unit. Use a full face shield when needed.
• UNLEADED FUEL
Always use clean, fresh unleaded fuel
• OIL
Refer to operator's manual for the proper
type of oil.

RULES FOR SAFE OPERATION

• SAFETY AND INTERNATIONAL SYMBOLS •
Read the operator's manual(s)
Thrown objects and loud noise
• Do not operate the engine faster than the speed needed to cut, trim
or edge. Do not run the engine at high speed when not cutting.
• Always stop the engine when cutting is delayed or when walking
from one cutting location to another.
• If you strike or become entangled with a foreign object, stop the engine
immediately and check for damage. Do not operate before repairing
damage. Do not operate the unit with loose or damaged parts.
• Stop the unit, switch the engine to off, and disconnect the spark
plug for maintenance or repair.
• Use only replacement parts or accessories recommended for this
tool that are distributed by Sears or a Craftsman outlet. Use of any
replacement parts or accessories purchased elsewhere may be
hazardous, and will also void your warranty.
• Keep unit clean of vegetation and other materials. They may
become lodged between the cutting attachment and shield.
• To reduce fire hazard, replace a faulty muffler and spark arrestor.
Keep the engine and muffler free from grass, leaves, excessive
grease or carbon build up.

OTHER SAFETY WARNINGS

• Never store the unit with fuel in the tank, inside a building where
fumes may reach an open flame (pilot lights, etc.) or sparks
(switches, electrical motors, etc.).
• Allow the engine to cool before storing or transporting. Be sure to
secure the unit while transporting.
• Store the unit in a dry area, locked up or up high to prevent
unauthorized use or damage, out of the reach of children.
• Never douse or squirt the unit with water or any other liquid. Keep
handles dry, clean and free from debris. Clean after each use, see
Cleaning and Storage Instructions.
• Keep these instructions. Refer to them often and use them to
instruct other users. If you loan someone this unit, also loan them
these instructions.

SAVE THESE INSTRUCTIONS

SYMBOL MEANING
• ON/OFF STOP CONTROL
ON / START / RUN
• ON/OFF STOP CONTROL
OFF or STOP
• KEEP BYSTANDERS AWAY
WARNING:
especially children and pets, at least 50 feet
(15 m) from the operating area.
• THROWN OBJECTS AND ROTATING
CUTTER CAN CAUSE SEVERE INJURY
WARNING:
cutting attachment shield in place. Keep
away from the rotating cutting attachment.
• SHARP BLADE
WARNING:
attachment shield. To prevent serious injury,
do not touch the line cutting blade.
• HOT SURFACE
WARNING:
housing or cylinder. You may get burned.
These parts get extremely hot from operation.
They remain hot for a short time after the unit is
turned off.
3
Keep all bystanders,
Do not operate without the
Sharp blade on cutting
Do not touch a hot muffler, gear