Starting/Stopping Instructions; Operating Instructions - Craftsman 316.79189 Operator's Manual

fuel and oil separate and leads to formation of acids during
storage. When using alcohol-blended fuel, use fresh fuel.
Using Blended Fuels
If you choose to use a blended fuel, or its use is unavoidable,
follow recommended precautions:

STARTING/STOPPING INSTRUCTIONS

WARNING:
Operate this unit only in a well-
ventilated outdoor area. Carbon monoxide exhaust
fumes can be lethal in a confined area.
WARNING:
Avoid accidental starting. Make sure
you are in the starting position when pulling the starter
rope (Fig. 5). To avoid serious injury, the operator and
unit must be in a stable position while starting.
STARTING INSTRUCTIONS
1. Mix gas with oil.
2. Fill the fuel tank with the fuel/oil mixture. See Oil and
Fuel Mixing Instructions.
NOTE: There is no need to turn the unit on. The On/Off
Stop Control is in the ON ( I ) position at all times.
3. Fully press and release the primer bulb 10 times,
slowly. Some amount of fuel should be visible in the
primer bulb and fuel lines (Fig. 4). If you can't see fuel
in the bulb, press and release the bulb as many times
as it takes until you can see fuel in it.
4. Crouch in the starting position (Fig. 5). Do not squeeze
the throttle, and pull the starter rope with a controlled and
steady motion until the unit starts. Wait 10 to 15 seconds,
then squeeze the throttle to control the cutting speed.
IF... the engine does not start, go back to step 3.
NOTE: The unit uses the Incredi-Pull™ starting system with
MAX FIRE IGNITION™ , which significantly reduces
the effort required to start the engine. You must pull
the starter rope out far enough to hear the engine
attempt to start. There is no need to pull the rope
briskly-- there is no harsh resistance when pulling. Be
aware that this starting method is vastly different from
(and much easier than) what you may be used to.
NOTE: Hot Starting
If the unit is hot and fails to start within 3 pulls of
the starter rope, squeeze the throttle control and
pull the starter rope until the unit starts.
STOPPING INSTRUCTIONS
1. Release your hand from the throttle control. Allow the
engine to cool down by idling.
WARNING:
Always wear eye, hearing, foot and
body protection to reduce the risk of injury when
operating this unit.
HOLDING THE TRIMMER
Before operating the unit, stand in the operating position (Fig.
6). Check for the following:
• The operator is wearing eye protection and proper clothing
• With a slightly-bent right arm, the operator's hand is holding
the shaft grip
• The operator's left arm is slightly bent, the left hand holding
the D-handle
• The unit is at waist level
• The cutting attachment is parallel to the ground and easily
contacts the grass without the need to bend over
• Always use the fresh fuel mix explained in the operator's manual
• Always shake the fuel mix before fueling the unit
• Drain the tank and run the engine dry before storing the unit
NOTE: Dispose of the old fuel/oil mix in accordance to
Federal, State and Local regulations.
Stop/Off (O)
Start/On ( I )
Equipped With
2. Press and hold On/Off Stop Control in the OFF (O) position
until engine comes to a complete stop (Fig. 3)

OPERATING INSTRUCTIONS

LINE REPLACEMENT
for Hassle-Free III™ Cutting Head
Always use Craftsman Hassle-Free
III™ XTRA QUIET Spiral Line. Choose
the line size best suited for the job at
hand. Red colored line is designed for
cutting grass and small weeds. Black
colored line is designed for cutting
larger weeds and light brush.
NOTE: Before inserting new line into
the holes in the cutting head,
identify the proper holes. Follow
directions as shown on the line
glide plate. Do Not attempt to
remove the cutting head from the
unit when replacing line.
6
Primer Bulb
Throttle
Control
Fig. 3
Trimmer
Incredi-Pull
Starting
Throttle Control
Fig. 5
Fig. 4
Starting
Position
Fig. 6