Table of Contents
Advertisement
Quick Links
LEDVANCE PHASE EV
Installation Guide
Level 2 Commercial Charger Pedestal
Item No: 78135
Model: EVCPED
Base pedestal for use with EVC48ALVL2C1XX (Level
2 Commercial EVSE).
Please Read All Instructions Before Attempting Installation
−
TO PREVENT PERSONAL INJURY OR PRODUCT DAMAGE ONLY LICENSED ELECTRICIANS SHOULD
PROVIDE ALL INSTALLATION SERVICES.
−
TO AVOID ELECTRIC SHOCK OR COMPONENT DAMAGE DISCONNECT POWER BEFORE ATTEMPTING
INSTALLATION OR SERVICING.
−
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE NATIONAL ELECTRIC CODE (NEC)
AND ALL APPLICABLE FEDERAL, STATE AND LOCAL ELECTRICAL CODES AND SAFETY STANDARDS.
−
ANY ALTERATION OR MODIFICATION OF THIS PRODUCT IS EXPRESSLY FORBIDDEN AS IT MAY
CAUSE SERIOUS PERSONAL INJURY, DEATH, PROPERTY DAMAGE AND/OR PRODUCT MALFUNCTION.
−
TO PREVENT PRODUCT MALFUNCTION AND / OR ELECTRICAL SHOCK THIS PRODUCT MUST BE
PROPERLY GROUNDED.
Page 1 of 9
WARNING
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Ledvance PHASE EV EVCPED
Summary of Contents for Ledvance PHASE EV EVCPED
- Page 1 LEDVANCE PHASE EV Installation Guide Level 2 Commercial Charger Pedestal Item No: 78135 Model: EVCPED Base pedestal for use with EVC48ALVL2C1XX (Level 2 Commercial EVSE). WARNING Please Read All Instructions Before Attempting Installation − TO PREVENT PERSONAL INJURY OR PRODUCT DAMAGE ONLY LICENSED ELECTRICIANS SHOULD PROVIDE ALL INSTALLATION SERVICES.
-
Page 2: Safety Precautions
Safety Precautions IMPORTANT: READ CAREFULLY BEFORE INSTALLING THE PEDESTAL. RETAIN FOR FUTURE REFERENCE. GENERAL: Upon receipt of the pedestal, thoroughly inspect for any freight damage which should be brought to the attention of the delivery carrier. What’s Included Item Description Quantity Image Pedestal... -
Page 3: Tools You Will Need
Tools You Will Need 1/4 in hex bit driver Phillips screwdriver (#2) Wire cutter & stripper Crimping pliers Hammer drill Level Eyes & ear protection Page 3 of 9... -
Page 4: Pedestal Installation
Pedestal Installation 1. Use the leveling plate as a template and mark the 4 holes on the concrete foundation. Make sure the power feed conduit is in the center as shown in the illustration below. Drill 4 holes using a 15/32” (12mm dia.) hammer drill bit to a minimum depth of 3-11/16”... - Page 5 3. Use the included flat washers, lock washers, and nuts to attach the pedestal to the anchor bolts. Loosely install the anchor nuts until the pedestal is level. M12*25mm Level the pedestal base by adjusting the leveling screw. leveling screws and the anchor nuts. Tighten the anchor nuts to secure the pedestal in its final position.
-
Page 6: Preparing The Charger
Installing the Mounting Plate to a Pedestal 1. Remove the 2 screws – one on each side of the charger to detach the mounting plate from the charger. 2. Use the included three (3) M5*12mm screws to attach the mounting plate to the pedestal. Preparing the Charger 1. - Page 7 2. Once the 3 screws are removed, carefully lift the cover outward and up to detach the cover frame. 3. Remove the 6 screws to take off the access panel cover. For Rear Wiring Remove the rear plug(s) by loosening the hex nut in a counterclockwise direction. Then use the same plug to cover the hole at the bottom of the charger.
-
Page 8: Mounting The Charger
Mounting the Charger 1. Align the charger to the mounting plate and hang it as shown in the illustration below. Next, secure the charger to the mounting plate with the 2 original screws. Strain relief must be installed for IP rating. - Page 9 3. Attach the holster and cable hanger to the pedestal as shown in the illustrations below. 4. Use the included rubber plugs to cover any unused holes. Tip: It’s easier to insert the plug by twisting it clockwise like you are hand tightening a screw. Page 9 of 9...
Need help?
Do you have a question about the PHASE EV EVCPED and is the answer not in the manual?
Questions and answers