Rear tine tiller with counter rotating tines 5.0 hp 17 inch tine width (21 pages)
Summary of Contents for Craftsman 917.29555
Page 1
Caution: Read and follow all Safety Rules and Instructions Before Operating This Equipment Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. COUNTER ROTATING TI oAssembUy • Operation , Customer Responsibilities oService and Adjustments oRepair Parts ®...
Never operate the tiller without good visibility or tight. • Be careful when tilling in hard ground The tines may catch in the ground and propel the tiller forward. If this occurs, let go of the handlebars and do not restrain the machine.
Page 3
Repairs necessary because of operator abuse or negligence, including bent crankshafts and the failure to maintain the equipment according to the instructions contained in the owner's manual, ° If this Craftsman Tiller is used for commercial or rental purposes, this Warranty applies for only 30 days from the date of purchase, WARRANTY...
Page 5
These accessories were available when the tiller was purchased. outlets, Catalog and Service Centers. Most Sears Stores can order repatr parts for you when you provide the mo del number of your tiller. ENGINE MUFFLER SPARK PLUG ,,, ,,, ..
Page 6
Your' new tiller has been assembled at the factory with exception of those parts left unassembled for' shipping purposes, To ensure safe and proper operation of your tiller all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary' to insure proper tightness.
° Rotate handle assembly down to install two carriage boIts and Iocknuts, Insert rear carriage bolt (Fig° 5) first, with head of bolt on L.H. side of tiller° Lower the handfe assembly,, Tighten bolts so handle moves with some resistance°...
(See Fig. 6) • Tilt tillerforward by lifting handle, Separate cardboard cover from leveling shield. • Rotate tiller handle to the right and pull tiller out of carton, INSERT CABLE • Insert plastic cable clip into hole on the back of handle column, Push cables into clip.
KNOW YOUR TILLER READ THIS OWNER'S MANUAL AND SAFEFY RULES BEFORE OPERATING YOUR TILLER, Compare the illustrations with your tiller to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference_ DRIVE CONTROL THROTTLE...
Hold drive control bar against the handle to start tiller movement. " _ I_l,I of any tiller can result in foreign objects thrown into the eyes, which can wide vision safety mask for over the spec- DEPTH The depth stake can be raised or lowered to allow you more versatile tilting and cultivating, or to more easily transport your tiller.
Page 11
• Release the depth stake pin Move the depth stake down to the top hole for transporting the tiller. Place depth stake pin in hole of depth stake to lock in position, This prevents tines from scuffing the ground °...
Page 12
• Tilling is digging into, turning over, and breaking up acked soil before planting_ Loose, unpacked elps root growth_ Best tilling depth is 4 to 6 '. A tiller will also clear the soil of unwanted vegetation, The decomposition soil. Depending on the climate (rainfall and wind), it...
Page 13
CULTIVATING Figs. 16 and • Place blocks under right hand side of tiller and remove hairpin clip and clevis pin from right hand wheel, • Move wheel outward approximately 1 inch (2.5 cm) until hole in inner wheel hub lines up with inner hole in...
2 - Service more often when operating in dirty or dusty conditions GENERAL RECOMIVlEN DATnONS The warranty on this tiller does not cover items that have been subjected to operator abuse or negligence. receive full value from the warranty, the operator must maintain tiller as instructed in this manual°...
Page 15
Change the oil after the first two hours of operation and every 25 hours thereafter or at least once a year if the tiller is not used for 25 hours in one year,.
Page 16
MUFFLER Do not operate tiller' without muffier_ Do not tamper with exhaust system, Damaged mufflers or spark arrestors could create a fire hazard. Inspect periodically and replace if necessary. If your engine is equipped attester screen assembly, remove every 50 hours for cleaning and inspection..
TO REMOVE BELT GUARD NOTE: For ease of removal, remove hairpin clip and clevis pin from left wheel. Pull wheel out from tiller about 1 inch. Remove two (2) cap nuts and washers from side of belt guard, Remove hex nut and washer from bottom of belt guard (located behind wheel), •...
Page 18
A badly worn tine causes your' tiller to work harder and dig more shallow. Most important, worn tines cannot chop and shred organic matter as effectively nor bury it as deeply as good tines.
Page 19
SERVICE A ENGINE TO ADJUST THROTTLE CONTROL (See Fig. 29) • Loosen cable clamp screw to allow cable to move, • Move throttte control lever on upper handle to "FAST" position, • Pull throttle cable out until engine bellcrank is back as far as it will go, °...
Page 20
30 days or more. CAUTION: Never store ttle tiller with gasoline in the tank inside a building where fumes may reach an open flame or spark.
Page 21
Excessive bounce/ Ground too dry and hard. difficult handling Ground too wet, Soil balls up or clumps Engine runs but tiller Drive control bar is not engaged. won't move V-beft not correctly adjusted V-belt ts off pulley(s),, Engine runs but labors Tilling too deep.
Page 22
REPAUR PARTS 5 HP 14" TILLER - - MODEL NUMBER HANDLES DESCRIPTION PART 110707X Cap, Sleeve 110674X Grip, Handle 110673X Grommet, Handle 127254X Bar', Drive Control Assembly 6712J Cap, Vinyl 137119 Panel, Control 110641X Bushing, Split * Screw,Mach. Pan Head. C_R.
Page 23
REPARR PARTS 5 HP 14" TILLER - - MODEL NUMBER MAINFRAME, LEFT SIDE PART DESCRIPTION STD541431 * Nut, Keps, Flange 5/16-18 STD551137 * Washer, Lock 3/8 STD541037 * Nut, Hex 3/8-16 74930568 Bolt, Hex 5/16-18 x 4-1/4 STD571810 * Pin, Roll...
Page 29
REPAIR PARTS 5 HP 14" TILLER - - MODEL NUMBER 917.295550 ENGINE, BRIGGS & STRATTON - - MODEL NUMBER 135202, TYPE NO. 0145-01 13oo...
Page 30
REPAURPARTS 5 HP 14" TILLER - - MODEL NUMBER 917.295550 ENGINE, BRIGGS & STRATTON - - MODEL NUMBER 135202, TYPE NO. 0145-01 "_...
Page 31
REPAnR PARTS 5 HP 14" TILLER - - MODEL NUMBER ENGINE, BRiGGS & STRATTON "A- REQUIRES SPECIAL TOOLS TO INSTALL INSTRUCTION MANUAL, 121 CARBURETOR OVERHAUL - - MODEL NUMBER 3°° SEE REPAIR 1016 917.295550 135202, TYPE NO. 0145-01 GASKET SET...
Each tilter has its own model number, number,. The model number for your tiller witl be found on a plate attached to the top of the transmission. The model number for your engine will be found on the blower housing of...