Kenwood 103AR Instruction Manual page 5

the system control connections
1D3AR |En)
i
ili
Connecting system control cords after connecting a KENWOOD audio component system lets you take advantage of convenient
system control operations. vuiivomem
There are two KENWOOD system control modes. Make connections according to the groups of terminal symbols shown below.
CXSSi
Mode; lets you combine
CXU. CXS^,
and
XS&
terminals
ELTB)
Mode: for
ELE)
terminals only
This unit IS compatible with both [XS8] and tSL161 modes. It comes from the factory set to the IXS8] mode. To switch to the [SL161
mode, follow the instructions in "SWITCHING FROM [XS8I TO [SL16I" below. ^
EXAMPLE: [XS8] mode connections
The underlined portion represents the setting of the system
control mode.
System
comrol
cord
System
control
cord
ISL16] [XS8]
[SL16]
[SL16] [)«] (XS81 [XR]
[SL16] IXS8]
[XS]
. Sc'r-e CD
D
ave^s 3'-:c: cassette aec.s are not corrtpanole with tne [SL161 syster-. control mode. Be sure to use tne [XSSI systerr^ control
■ o oe wne'- maKing systerri connections with eouipment that is not [SL161 compatible
# Some MD piave-s am not system control corrtpatibie You cannot make system control connections to this kind of equipment.
EXAMPLE: [SL16] mode connections
The underlined portion represents the setting of the system
control mode.
[SLtSl [XS81
[SLtSl
[SL16] [XS] [XS8] (XR)
ISL16] [XS] [XS8]
[XS]
;SLl6i eauip-em canrcr pe combmeo witr [XRi, [XSl. and [XSS] equipment for system opera¬
tions If ycu' eau.oment consists of this i^mo of combination,
cC'-tmi co'ds. Even v\ f'c-^t system cof'iro cords, no'
aY'ecnnQ oer'ormancc
1
, please do not connect any system
"ai operations can be earned out without
Jc no' connect sysie"' control cords to any components other than those specified by
KENWOOD It may cause a malfunction and damage you' equipment.
DO Sum the syste^' control plugs are mserteci all the way -n to the system control terminals
ABOUT THE SYSTEM CONTROL OPERATIONS
Remote Control
(Except
(SL16])
Lets you operate source components with the system re¬
mote supplied with this unit.
Automatic Operation (Except [XR] equipment)
When you start playback from a source component, the in¬
put selector on this unit switches to that component auto¬
matically
Synchronized Recording (Except [XR] equipment)
Lets you synchronize recording with the start of playback
when recording from CD, MD, or analog discs.
SWITCHING FROM [XSS] TO [SL16]
You can easily change the system control mode with the
following operation. Do this operation after completing all
connections.
Switching to [SL161:
Switching back to [XS8]:
Unplug the AC power cord from
the wall outlet, then plug it back
in while holding down the AUTO/
MANUAL key .
Unplug the AC power cord from
the wall outlet, then plug it back
in while holding down the BAND
key .
• ThfS operation wil not affect items stored in the memory
Not 3
T.ne system control mode will revert to [XS8i if the
cower cord is disconnected from the AC outlet for
thme consecutive aays. If you would like to make
tne unit completely (and permanently.) ISL161 com¬
patible. please consult your nearest retailer or the
KENWOOD Marketing Department
1 Connect all coras nrm:y if connections are loose, mere could be loss of sound or noise produced.
2 V\ Dg" plugging and unplugging co-nectio-' cords, be sure to first remove the power cord from the AC outlet Pluqqmq / unplua-
g.-,g ccmneciion cords without mmova! of tne oowe^ coid can cause malfunctions or damage to the umt