Toshiba Portege M700-0GJ01J Reference Manual
Toshiba Portege M700-0GJ01J Reference Manual

Toshiba Portege M700-0GJ01J Reference Manual

Toshiba portege m700-0gj01j: reference guide
Hide thumbs Also See for Portege M700-0GJ01J:

Advertisement

Portégé
Series Resource Guide
If you need assistance:
❖ Toshiba's Support Web site
pcsupport.toshiba.com
❖ Toshiba Global Support Centre
Calling within the United States (800) 457-7777
Calling from outside the United States (949) 859-4273
Please fill in for your reference and future use:
Model name______________________________________
Part number______________________________________
Serial number____________________________________
®
M700/M705
Keep this guide in a convenient place to access important
information about your computer.

Advertisement

Table of Contents
loading

Summary of Contents for Toshiba Portege M700-0GJ01J

  • Page 1 Series Resource Guide Keep this guide in a convenient place to access important information about your computer. If you need assistance: ❖ Toshiba’s Support Web site pcsupport.toshiba.com ❖ Toshiba Global Support Centre Calling within the United States (800) 457-7777 Calling from outside the United States (949) 859-4273...
  • Page 2: Table Of Contents

    Contents Introduction ... 21 Setting up your computer and getting started... 22 Adding memory (optional)... 26 Your computer’s TFT display ... 32 Inserting a PC Card... 32 Removing a PC Card... 33 Learning the basics... 33 Using the TouchPad™ ... 34 Using the optical drive ...
  • Page 3 ALTERED OR LOST DUE TO ANY TROUBLE, FAILURE OR MALFUNCTION OF THE HARD DISK DRIVE OR OTHER STORAGE DEVICES AND THE DATA CANNOT BE RECOVERED, TOSHIBA SHALL NOT BE LIABLE FOR ANY DAMAGE OR LOSS OF DATA, OR ANY OTHER DAMAGE RESULTING THEREFROM. WHEN COPYING OR TRANSFERRING YOUR DATA, PLEASE BE SURE TO CONFIRM WHETHER THE DATA HAS BEEN SUCCESSFULLY COPIED OR TRANSFERRED.
  • Page 4 TOSHIBA, ASSUME FULL RESPONSIBILITY FOR SUCH USE. EU Declaration of Conformity TOSHIBA declares that this product conforms to the following Standards: This product is carrying the CE-Mark in accordance with the related European Directives. The party responsible for CE-Marking is TOSHIBA Europe GmbH, Hammfelddamm 8, 41460 Neuss, Germany.
  • Page 5 2. If this equipment causes RF interference to other radio stations, promptly change the frequency being used, change the location of use, or turn off the source of emissions. 3. Contact TOSHIBA Direct PC if you have problems with interference caused by this product to Other Radio Stations. 2. Indication The indication shown below appears on this equipment.
  • Page 6: Device Authorization

    The interference range of this equipment is less than 40m. 2,400 MHz to 2,483.5 MHz. It is possible to avoid the band of mobile object identification systems. 3. TOSHIBA Direct PC Monday – Friday: 10:00 – 17:00 Toll Free Tel: 0120-15-1048...
  • Page 7 This device works on passive scan only. A peer-to-peer mode is not available in 802.11a and Turbo Mode. 802.11b (2.4 GHz) Australia Canada France Ireland Luxembourg Norway Switzerland Europe - Restrictions for use of 2.4 GHz Frequencies in European Community Countries België/ For private usage outside buildings across public grounds over less than Belgique:...
  • Page 8 Nederland: License required for outdoor installations. Check with reseller for procedure to follow. Licentie verplicht voor gebruik met buitenantennes. Neem contact op met verkoper voor juiste procedure. 802.11a (5 GHz) Australia Canada France Ireland Luxembourg Norway Switzerland Turbo Mode (5 GHz) Canada Europe - Restrictions for Use of 5 GHz Frequencies in European Community Countries...
  • Page 9 ❖ This device must not be operated in ad-hoc mode using channels in the 5 GHz bands in the European Community. Ad-hoc mode provides a direct communication between two client devices without a Wireless LAN Access Point. ❖ This device must be used with Access Points that have employed and activated a radar detection feature required for European Community operation in the 5 GHz bands.
  • Page 10: Wireless Lan Card

    Mexico Norway Singapore Switzerland Approved Countries/Regions for use for the Toshiba Mini PCI Wireless LAN Card This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
  • Page 11 Approved Countries/Regions for use ® Intel PRO/Wireless 3945ABG Network Connection This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. An adhoc mode is available in Ch1-Ch11(802.11b/g), An Infrastructure mode is available in Ch1-Ch11 (802.11b/g) Ch36,40,44,48,52,56,60,64,149,153,157,161,165 (802.11a) Wake-up on wireless lan function is not available in battery mode.
  • Page 12: Bluetooth Wireless Technology Interoperability

    11a, 11b, 11g and 11n wireless are based on IEEE 802.11a, 802.11b, 802.11g and 802.11n respectively. The IEEE 802.11n specification has not been finalized and is currently in draft release. The TOSHIBA 11a/b/g/n Wireless LAN Adapters are based on the Draft Release, Version 1.0, of the IEEE 802.11n specification.
  • Page 13 Bluetooth Approved Countries/Regions for use (Bluetooth technology) ® Bluetooth Card from Toshiba equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. Australia...
  • Page 14: Bluetooth Wireless Technology And Your Health

    TOSHIBA under license. ® Using Bluetooth Card from TOSHIBA equipment in Japan In Japan, this product is classified into the second generation of low-power data communication system, and using the frequency band from 2,400MHz to 2,483.5MHz. That frequency band is overlapped with the band which has been using by mobile object identification systems (premises radio station and specified low-power radio station).
  • Page 15 2. If this equipment causes RF interference to other radio stations, promptly change the frequency being used, change the location of use, or turn off the source of emissions. 3. Contact TOSHIBA Direct PC if you have problems with interference caused by this product to Other Radio Stations. 2. Indication The indication shown below appears on this equipment.
  • Page 16: Regulatory Statements

    Regulatory statements General This product complies with any mandatory product specification in any Country/ Region where the product is sold. In addition, the product complies with the following: European Union (EU) and EFTA This equipment complies with the R&TTE directive 1999/5/EC and has been provided with the CE mark accordingly.
  • Page 17 TOSHIBA is not responsible for any radio or television interference caused by unauthorized modification of the devices included with this Bluetooth from TOSHIBA, or the substitution or attachment of connecting cables and equipment other than specified by TOSHIBA. The correction of interference caused by such unauthorized modification, substitution or attachment will be the responsibility of the user.
  • Page 18 This guide is copyrighted by Toshiba America Information Systems, Inc. with all rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed, however, with respect to the use of the information contained herein.
  • Page 19 INFORMATION CONTAINED HEREIN AND HEREBY EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE WITH REGARD TO ANY OF THE FOREGOING. TOSHIBA ASSUMES NO LIABILITY FOR ANY DAMAGES INCURRED DIRECTLY OR INDIRECTLY FROM ANY TECHNICAL OR TYPOGRAPHICAL ERRORS OR OMISSIONS CONTAINED HEREIN OR FOR DISCREPANCIES BETWEEN THE PRODUCT AND THE MANUAL.
  • Page 20 Card is a trademark of Fuji Photo Film, Co., Ltd. Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Toshiba is under license. Other trademarks and trade names are those of their respective owners.
  • Page 21: Introduction

    (RoHS), which restricts use of lead, cadmium, mercury, hexavalent chromium, PBB, and PBDE. Toshiba requires its notebook component suppliers to meet RoHS requirements and verifies its suppliers’ commitment to meeting RoHS requirements by conducting component sampling inspections during the product design approval process.
  • Page 22: Setting Up Your Computer And Getting Started

    For accessory information, visit Toshiba’s Web site at accessories.toshiba.com. Setting up your computer and getting started The Toshiba Instruction Manual for Safety and Comfort, included with your computer, contains helpful information for setting up your work environment and tips for working comfortably throughout the day.
  • Page 23 Never allow any liquids to spill into any part of your computer, and never expose the computer to rain, water, seawater or moisture. Exposure to liquid or moisture can cause electric shock or fire, resulting in damage or serious injury. If any of these eventualities should accidentally occur, immediately: 1.
  • Page 24 TOSHIBA Battery Charger (that may have been provided with your computer), or use AC adaptors and battery chargers specified by TOSHIBA to avoid any risk of fire or other damage to the computer. Use of an incompatible AC adaptor or Battery Charger could cause fire or damage to the computer, possibly resulting in serious injury.
  • Page 25 To connect AC power to the computer: Connect the power cord/cable to the AC adaptor. (Sample Illustration) Connecting the power cord/cable to the AC adaptor Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm.
  • Page 26: Adding Memory (Optional)

    Adding memory (optional) HINT: To purchase additional memory modules, see the accessories information packaged with your system or visit accessories.toshiba.com. Your computer comes with enough memory to run most of today’s popular applications. You may want to increase the computer’s memory if you use complex software or process large amounts of data.
  • Page 27 Installing a memory module A memory module can be installed in the memory module slot on the base of the computer. You will need a small Phillips screwdriver for this procedure. If the computer has been running recently, the memory module may be hot.
  • Page 28 Adding memory (optional) Before you turn the computer over, make sure that the computer display is properly closed and is not in tablet mode. Setting the computer down on the display may cause damage to the screen. (Sample Illustration) Locating the memory module slot cover Using a small Phillips screwdriver, loosen the captive screw that secures the memory module slot cover.
  • Page 29 Avoid touching the connector on the memory module or on the computer. Grease or dust on the connector may cause memory access problems. Carefully remove the new memory module from its antistatic packaging, without touching its connector. 10 Locate an empty memory module slot on the underside of the computer.
  • Page 30 Adding memory (optional) 13 Once the module’s connector is fully inserted into the socket, press downward on the top edge of the module to seat the module into the latches at the sides of the socket. These latches should “snap” into place securely with the corresponding cutouts in the side of the module.
  • Page 31 TECHNICAL NOTE: You must have at least one memory module installed for the computer to work. Removing a memory module If you need to remove a memory module: Complete steps 1–8 in “Installing a memory module” on page 27 to shut down the computer and open the memory module slot cover.
  • Page 32: Your Computer's Tft Display

    Your computer’s TFT display Your computer’s TFT display Small bright dots may appear on your screen display when you turn on your computer. Your display contains an extremely large number of thin-film transistors (TFT) and is manufactured using high- precision technology. Any small bright dots that may appear on your display are an intrinsic characteristic of the TFT manufacturing technology.
  • Page 33: Removing A Pc Card

    Removing a PC Card Be sure to disable the PC Card prior to removing it. Otherwise, the system may be damaged. Before removing a PC Card, make sure that no applications or system services are using the card. Prepare the card for removal by clicking the Safely Remove Hardware icon in the Notification Area and then selecting the PC Card device.
  • Page 34: Using The Touchpad

    Using the TouchPad™ The Windows desktop setup, during its shutdown procedure. If you do not let the Windows icon positions may be lost. Using the TouchPad The TouchPad™, the small, smooth, square cutout located in front of the keyboard, is sensitive to touch and enables you to move the cursor with the stroke of a finger.
  • Page 35: Using The Optical Drive

    Using the optical drive Optical storage has become the preferred medium for software, music, and video. Digital versatile discs (DVDs) provide a significant increase in data storage and support features that are not available on any other video platform. These features include wide- screen movies, multiple language tracks, digital surround sound, multiple camera angles, and interactive menus.
  • Page 36 Using the optical drive Manual eject hole—Use if you need to release the disc tray when the power is off. Use a straightened paper clip or other narrow object to press the manual eject button located inside the hole. Never use a pencil to press the manual eject button. Pencil lead can break off inside the computer and damage it.
  • Page 37: Moving The Computer

    If you insert the disc incorrectly, it may jam the drive. If this happens, contact Toshiba support for assistance. Push the disc tray in by pressing gently on the center of the tray until it clicks into place.
  • Page 38: Mobile Computing

    ❖ EasyGuard Optimize—to enable users to customize system settings to be more productive. *Toshiba EasyGuard some of which may or may not be available on a particular Toshiba notebook depending on the model selected. See easyguard.toshiba.com for detailed information. Running the computer on battery power...
  • Page 39 To ensure that the battery maintains its maximum capacity, operate the computer on battery power at least once a month. The Lithium- Ion battery has no memory effect so it is not necessary to let the battery fully discharge each time. However, for better accuracy of the battery meter, it is helpful to fully discharge the battery periodically.
  • Page 40 Mobile computing TECHNICAL NOTE: The recharging of the battery cannot occur when your computer is using all of the power provided by the AC adaptor to run applications, features, and devices. Your computer's Power Options utility can be used to select a power level setting that reduces the power required for system operation and will allow the battery to recharge.
  • Page 41 Slide the battery release lock to the unlocked position. (Sample Illustration) Unlocking the battery release lock Slide the battery release latch to release the battery. Pull the discharged battery out of the computer. (Sample Illustration) Removing the battery If the battery is leaking or its case is cracked, put on protective gloves to handle it, and discard it immediately.
  • Page 42: Taking Care Of Your Battery

    ❖ If a battery is leaking or damaged, replace it immediately. Use protective gloves when handling a damaged battery. ❖ To replace the battery, use an identical battery that you can purchase through the Toshiba Web site at accessories.toshiba.com. ❖ A reverse polarity condition should be avoided with all batteries.
  • Page 43 Maintaining your battery Fully discharging your battery pack will allow better accuracy of the battery meter. To fully discharge your battery pack: ❖ Periodically, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges.
  • Page 44 If you cannot find the information you need elsewhere, call Toshiba at: (800) 457-7777. Toshiba is dedicated to preserving the environment by sponsoring Call2Recycle™, a program of the Rechargeable Battery Recycling...
  • Page 45: If Something Goes Wrong

    If something goes wrong Problems that are easy to fix Your program stops responding. If you are working with a program that suddenly freezes all operations, chances are the program has stopped responding. You can exit the failed program without shutting down the operating system or closing other programs.
  • Page 46 If something goes wrong To record the details: Click the Details button and select the text the operating system displays. The Details button displays information that the software manufacturer needs to help you solve your problem. Press Ctrl Open Notepad (click Start, All Programs, Accessories and then click Notepad).
  • Page 47 The keyboard produces unexpected characters. A keypad overlay may be on. If the numlock light or cursor control mode light is on, press light, or If the problem occurs when both the keypad overlays are off, make sure the software you are using is not remapping the keyboard. Refer to the software documentation and check that the program does not assign different meanings to any of the keys.
  • Page 48 If something goes wrong Small bright dots appear on your TFT display when you turn on your computer. Small bright dots may appear on your screen display when you turn on your computer. Your display contains an extremely large number of thin-film transistors (TFT) and is manufactured using high- precision technology.
  • Page 49: If You Need Further Assistance

    Contact the software company’s technical support group for their assistance. For the number of a Toshiba dealer near you, see “Toshiba voice contact” in this section. Contacting Toshiba If you still need help and suspect that the problem is hardware- related, Toshiba offers a variety of resources to help you.
  • Page 50: Power Cord/Cable Connectors

    ❖ Information about what you were doing when the problem occurred ❖ Exact error messages and when they occurred For technical support, call the Toshiba Global Support Centre: Within the United States at (800) 457-7777 Outside the United States at (949) 859-4273...
  • Page 51 Index AC adaptor AC power light backing up files battery changing installing 40, 41 notification real-time clock (RTC) removing buttons eject, optical drive TouchPad™ control CD/DVD inserting changing battery computer moving setting up computing tips connecting AC adaptor power cord/cable printer control buttons TouchPad™...
  • Page 52 TouchPad™ printer connecting problem solving computer hangs when PC Card inserted computer will not start contacting Toshiba display is blank external monitor illegal operation keyboard not responding keyboard produces unexpected characters PC Card checklist PC Card slot appears dead...

Table of Contents