Advertisement
Quick Links
Advertisement
Related Manuals for D'Orly PCN70
Summary of Contents for D'Orly PCN70
- Page 1 MANUAL PCN70...
- Page 2 OPERATING INSTRUCTIONS FOR FASTENER DRIVING TOOLS OPERATED BY COMPRESSED AIR AIR-POWERED COIL NAILER Model No.: MCN70 IMPORTANT: Read all safety rules and operating Instructions carefully before first use it. Keep this Manual for future reference. Residual risks Even when the tool is used as prescribed it is not possible to eliminate all residual risk factors. The following hazards may arise in connection with the tool’s construction and design: Damage to lungs if an effective dust mask is not worn.
-
Page 3: Maintenance & Troubleshooting
TABLE OF CONTENTS:QUICK START GUIDE TECHNICAL SPECIFIACTIONS SAFETY GUIDELINES KEY PARTS DIAGRAM IMPORTANT INFORMATION TYPES OF FASTENERS OPERATING INSTRUCTIONS MAINTENANCE TROUBLESHOOTING EXPLODED VIEW PARTS LIST WARRANTY TECHNICAL SPECIFIACTIONS Magazine capacity(QTY.) 225-300pcs Nailer 45-70mm... - Page 4 DANGER! Potential hazard that will result in serious injury or loss of life. Keep children away from the work area. Do not allow children to handle power tools. Keep air hose away from heat, oil, and sharp edges. Check air hose for wear before each use and ensure that all connections are proper.
- Page 5 Do not carry the compressor while it is running. Do not operate the compressor if it is not in a stable position. Do not operate the compressor on a rooftop or in an elevated position that could allow the unit to fall or be tipped over.
-
Page 6: Key Parts Diagram
KEY PARTS DIAGRAM Description Description Magazine Trigger Gun Body Air inlet plug Cylinder Cap IMPORTANT INFORMATION Compatible compressors GUIDELINES FOR PROPER USE AND OPERATION Be sure to use a proper air compressor with air powered tools. The compressor should be able to supply a minimal air delivery of 6.36SCFM @ 90PSI to ensure the compressor can run continuously with the air nailer. - Page 7 applicable. Verify that all of the connections in the air supply system are sealed in order to prevent air from leaking. Description Description AEROPRO Air powered Brad nailer Regulator(0 to 8.3 Bar) Quick connector Filter Quick coupler Cut-off valve Air Hose Air compressor Lubricator...
- Page 8 OPERATING INSTRUCTIONS 4.1 Preparing a tool for first time operation Please Read and observe these Operating Instruction before using the tool. Basic safety measures should always be strictly followed to protect against damage to the equipment and personal injury to the user or other people working in the vicinity of operation.
-
Page 9: Maintenance
WARNING! Potential hazard that could result in serious injury or loss of life. 5. Maintenance Disconnect the tool from the compressor before adjusting, clearing jams, servicing &maintenance, relocating and during non operation. Regular lubrication, if your tool without using the in-liner automatic oilier, place 2 or 6 drops of pneumatic tool oil into the air inlet before each work day or after 2 hours of continuous use depending in the characteristic of workpiece or type of fasteners. - Page 10 screws and caps to avoid personal injury. This should be done by an expert. Make regular inspection for free movement of trigger, Spring and safety mechanism to assure safe system is complete and functional: no loose and missing parts, no building or stocking parts. Keep magazine and nose of tool clean and free of any dirt lint or abrasive particles.
- Page 11 Explode drawing & Parts list Air Coil Nailer MCN70 www.aeroprotools.com...
- Page 12 CODE DESCRIPTION CODE DESCRIPTION Qty. 03.04.28.092 cylinder cap 03.04.08.183 nail head 03.04.05.049 bolt M6x35 03.04.01.277 O-ring 4.2x1.6 03.04.40.353 cylinder cap plug 03.04.36.012 Compressed spring 03.04.16.118 safety frame 03.04.16.120 safety frame 03.04.06.131 sealing gasket 03.04.35.071 protective film 03.04.40.367 spring seat 03.04.40.052 rubber plug 13.04.36.274 compressed spring...
- Page 13 CODE DESCRIPTION Qty. CODE DESCRIPTION Qty. O-ring 15.8x1.8 valve seat 03.04.32.025 nail length adjusting seat O-ring 11.3x1.85 03.04.05.049 bolt M6x35 O-ring 19x2.5 03.04.06.089 rubber gasket switch seat 03.04.31.122 shaft pin pin 2x15 03.04.40.370 magazine 03.04.40.351 O-ring 6x1.9 03.04.40.358 nail head protecter switch assembly O-ring 6.4*2 03.04.29.188...