UK - INSTALLATION – USE - MAINTENANCE ..........................6 GENERAL PRESCRIPTIONS ..................................6 DISPOSAL OF PACKING AND OF THE APPLIANCE ................................6 SAFETY DEVICES ..........................................7 INSTRUCTIONS FOR INSTALLATION ................................7 REMINDERS FOR THE INSTALLER ..................................... 7 REFERENCE STANDARDS AND LAWS ....................................7 UNPACKING .............................................
UK - INSTALLATION – USE - MAINTENANCE Unless they are supervised or instructed in its use by a person responsible for their safety. GENERAL PRESCRIPTIONS Do not leave de appliance unattended in presence of children and ensure that the latter do not have acces to the appliance.
The packing is made using environmentally The appliance is equipped with a manual reset friendly materials. plastic recyclable safety thermostat that interrupts heating when components are: the operating temperature exceeds the maximum the transparent cover, the bags containing the permitted value. instructions manual and nozzles (made of To restore appliance operation, remove the Polyethylene - PE).
extractor hood. 5. UNPACKING " B11 " TYPE APPLIANCE Check the state of the packing and in the event of Fit the “B11” type appliance with a suitable fl ue, damage, ask the delivery person to inspect the available from the appliance manufacturer. Follow goods.
Connect the power supply cable to the terminal board as shown in the wiring diagram supplied 8. CONVERSION TO ANOTHER with the appliance. TYPE OF GAS Secure the power supply cable with the cable clamp. Protect the power supply cable on the outside of Table Tab1 specifies: the appliance with a rigid plastic or metal pipe.
indicated in table TAB1. REPLACING THE NOZZLE AND THE MAIN BURNER Retighten nozzle UM. PRIMARY AIR REGULATION Reassemble all parts. For assembly, proceed in Remove the control panel. reverse order. Remove nozzle UM and replace it with the one indicated in table TAB1. GAS STOCKPOT STOVE Retighten nozzle UM.
Chapter “ INSTRUCTIONS FOR USE “ and check: service contract. The appliance is designed for professional use and the gas supply pressure (see next Paragraph). must be operated by trained personnel. the correct ignition of the burners and the The appliance is to be used for cooking food as effectiveness of the fumes removal system.
operation. The pilot flame can be seen through the peep hole on the control panel. MAX. FLAME The pilot light can be lit by bringing an open flame up to the nozzle. Raise the central disc on the MIN. FLAME hotplate.
MAIN BURNER IGNITION The appliance is designed for cooking foods placed Turn the knob to the chosen temperature setting on the grilles provided. for cooking. Do not leave the door even partially open during Press the knob for 5-10 seconds. The burner is use.
Use flat bottomed pans. Do not leave the hotplates switched on with no The appliance is designed for cooking foods pan or an empty pan in place. contained in pots and pans. Check that the flame spreaders are correctly Do not pour cold liquids onto the hot hotplate. placed on the burners.
The electric oven is controlled by two knobs (for SWITCHING ON AND OFF selecting the type of heating and the cooking temperature). A yellow indicator light indicates The thermostat control knob has the following operation of the heating elements. positions: The control knob has the following positions: MINIMUM TEMPERATURE OVEN LAMP...
the green lamp indicate that the appliance is clean the appliance. under voltage SATIN FINISH STAINLESS STEEL SURFACES TURNING OFF Clean the surfaces with a cloth or sponge using Turn the thermostat knob to position " 0 " . water and proprietary non-abrasive detergents. Follow the direction of the satin finish lines.
Insufficient gas supply pressure. 22. CONVERSION TO ANOTHER TYPE OF Blocked tubing or nozzle. Defective gas tap or valve. Defective burner (gas outlet holes clogged). See Chapter “ Instructions for installation “. GAS OVEN 23. COMMISSIONING THE MAIN BURNER DOESN’T TURN ON See Chapter “...
ELECTRIC COOK TOP/ELECTRIC STOCKPOT STOVE GAS SOLID TOP RANGES THE HOTPLATE DOES NOT HEAT. REPLACING THE GAS TAP AND PIEZO IGNITER. Possible causes: Remove the control panel. Hotplate defective. Remove and replace the component. Reassemble all parts. For assembly, proceed in reverse order.
REPLACING THE GAS TAP. REPLACING THE HEATING ELEMENT Remove the oven floor (only for lower heating Remove the control panel. elements). Remove and replace the component. Undo the screw securing the element to the oven Reassemble all parts. For assembly, proceed in and pull the element out by approx.
Page 18
ELECTRIC HOB Control knob Hotplate Indicator light ELECTRIC OVEN Control knob Working thermostat Safety thermostat Heating element Indicator light...