Related Manuals for Johnson Controls ioSmart Gen 1
Summary of Contents for Johnson Controls ioSmart Gen 1
- Page 1 Gen 1 Card Reader Installation Guide Building Technologies & Solutions A16381AH4G www.kantech.com 2022-10-27 *A16381AH4G* A16381AH4G-E...
- Page 2 Gen 1 Card Reader Installation Guide...
-
Page 3: Table Of Contents
Six pole screwless terminal block...................... 22 RS-485 mode............................... 22 Wiegand mode............................22 RS-485 wiring............................23 RS-485 CAT5 wiring..........................24 RS-485 lock output wiring........................25 BLE lock output wiring for panel-less mode..................26 Wiegand wiring............................ 27 ioSmart Gen 1 Card Reader Installation Guide... - Page 4 Configuring the reader's OSDP address...................36 Compliance specifications..........................37 FCC.................................37 CE compliance............................38 UL Standards compliance........................38 NIST (National Institute of Standards and Technology)..............38 RoHS (Restriction on Hazardous Substances)..................38 WEEE (Waste Electrical and Electronic Equipment)................. 38 ioSmart Gen 1 Card Reader Installation Guide...
-
Page 5: End-User License Agreement
+1 829 235 3047 El Salvador, San Salvador Direct +503 2 136 8703 Guatemala, Guatemala City Direct +502 2 268 1206 Mexico, Mexico City Direct +52 55 8526 1801 Panama, Panama City Direct +507 836 6265 ioSmart Gen 1 Card Reader Installation Guide... -
Page 6: Europe, Middle East, And Africa
+44 330 777 1300 Asia Pacific For technical support, contact us at one of the following email addresses or use the phone number for your area. • For video technical support, email video-support@jci.com. ioSmart Gen 1 Card Reader Installation Guide... -
Page 7: Copyright Information
Oceania and New Zealand Direct +64 9942 4004 Copyright information © 2022 Johnson Controls. All rights reserved. JOHNSON CONTROLS and KANTECH are trademarks of Johnson Controls. Safety instructions This equipment, RS-485 ioSmart Card Reader, shall be installed and used within an environment that provides the pollution degree max 2 and overvoltages category II, in NON HAZARDOUS LOCATIONS only. - Page 8 The ioSmart card readers support the following formats: • Standard 34-bit format • Standard 26-bit format • Most common HID formats • Other Kantech proprietary formats including eXtended Secure Format (XSF) and Smartcard Secure Format (SSF) ioSmart Gen 1 Card Reader Installation Guide...
-
Page 9: Unpacking The Iosmart Card Reader
In most instances, there are strict limitations to installing fail-secure devices and fail-safe locking devices such as magnetic locks or other similar locking devices on doors that are used as emergency exits. ioSmart Gen 1 Card Reader Installation Guide... -
Page 10: Changing The Iosmart Card Reader From Standard To Panel-Less Mode
Changing the ioSmart card reader from panel-less to standard mode To change the ioSmart card reader from panel-less mode to standard mode, set the reader to factory default or perform a hard reset on the reader. ioSmart Gen 1 Card Reader Installation Guide... -
Page 11: Upgrading The Iosmart Card Reader
13.56 MHz KT-MUL-MT Multi-technology Mullion 13.56 MHz + 125 kHz KT-MUL-MT-KP Multi-technology Mullion with a keypad 13.56 MHz + 125 kHz The following figure shows the dimensions of the Mullion ioSmart card reader. ioSmart Gen 1 Card Reader Installation Guide... - Page 12 1.770 in. (44.96 mm) Reader with a keypad Rear view of the reader 0.643 in. (16.32 mm) 3.254 in. (82.65 mm) 0.669 in. (16.99 mm) Elevation 0.964 in. (24.48 mm) 4.565 in. (115.95 mm) ioSmart Gen 1 Card Reader Installation Guide...
-
Page 13: Single Gang Iosmart Card Reader
2.820 in. (71.63 mm) Reader with a keypad Rear view of the reader 0.643 in. (16.32 mm) 3.254 in. (82.65 mm) 0.669 in. (16.99 mm) Elevation 0.964 in. (24.48 mm) 4.565 in. (115.95 mm) ioSmart Gen 1 Card Reader Installation Guide... -
Page 14: Technical Features
• When you tap the keypad. The first tap is not considered an entry. • When you swipe a card. After the backlighting illuminates, you can enter digits. ioSmart Gen 1 Card Reader Installation Guide... -
Page 15: Auto-Detection
200 mA / 80 120 mA / 120 mA / 200 mA / 80 120 mA / 70 120 mA / (mA) at 12 VDC 70 mA 70 mA 70 mA peak /average ioSmart Gen 1 Card Reader Installation Guide... - Page 16 -40°C to +70°C (-40°F to +158°F) temperature -35ºC to +66ºC (-31ºF to +151ºF) for a UL listed product Operating humidity 0 to 95% non-condensing. UL verified at 85% Rh. LED indicator Multi-color bar: red, green, yellow, blue. Configurable. ioSmart Gen 1 Card Reader Installation Guide...
-
Page 17: Mounting
Pull the controller’s wires from the wall and put them through the hole in the mounting plate. Attach the mounting plate to a flat wall using two screws. The screws are not included. Note: Do not over tighten the screws, especially if mounting on an uneven wall. ioSmart Gen 1 Card Reader Installation Guide... - Page 18 Fasten the white reflector tab into the mounting plate hole using a screw. The screw is not included. Use a wall anchor if necessary. Figure 6: Mounting plate tamper tab and screw hole ioSmart Gen 1 Card Reader Installation Guide...
-
Page 19: Wiring
The following table outlines the maximum cable distances between the reader and the controller. The results are based on using a KT-400 rev1 or a KT-1. To obtain results for a KT-400 with heat sinks, divide the distance by half. ioSmart Gen 1 Card Reader Installation Guide... - Page 20 Reverse 1 x reader with keypad 4 x reader with keypad (250 ft) Wiegand* Note: *Reverse Wiegand is available only with ioSmart SSF and ioProx XSF readers and cards on the KT-400 controller. ioSmart Gen 1 Card Reader Installation Guide...
- Page 21 Figure 8: Example of a home run RS-485 connection Table 12: Example of a home run RS-485 connection Callout Description RS-485 (COM2) 500 ft for each line IN readers OUT readers Door contacts T.REX (request to exit) detectors ioSmart Gen 1 Card Reader Installation Guide...
-
Page 22: Six Pole Screwless Terminal Block
BUZ and LED terminals and not inputs. The Wiegand mode output formats are as follows: • Kantech Smartcard Secure Format (SSF) is the default transmission • Kantech eXtended Secure Format (XSF) transmission • 34-bit transmission • 26-bit transmission ioSmart Gen 1 Card Reader Installation Guide... -
Page 23: Rs-485 Wiring
Description Mullion reader Single Gang reader Rear view of the reader Host controller RS-485 (COM2) interface Optional zone inputs 1 and 2. Individually programmable. Zone termination: NC, NO, NEOL, SEOL or DEOL termination. ioSmart Gen 1 Card Reader Installation Guide... -
Page 24: Rs-485 Cat5 Wiring
Description Mullion reader Single Gang reader Rear view of the reader Host controller RS-485 (COM2) interface Optional zone inputs 1 and 2. Individually programmable. Zone termination: NC, NO, NEOL, SEOL or DEOL termination. ioSmart Gen 1 Card Reader Installation Guide... -
Page 25: Rs-485 Lock Output Wiring
Table 16: RS-485 lock output wiring Callout Description Mullion reader Single Gang reader Rear view of the reader Host controller RS-485 (COM2) interface Input 1 programmed as dual input configuration Input 2 programmed as output device configuration ioSmart Gen 1 Card Reader Installation Guide... -
Page 26: Ble Lock Output Wiring For Panel-Less Mode
Mullion reader Single Gang reader Rear view of the reader External 12 VDC power supply Input 1 programmed as dual input configuration (door contact and REX) Input 2 programmed as output device configuration ioSmart Gen 1 Card Reader Installation Guide... -
Page 27: Wiegand Wiring
(D0 and D1). The following wiring diagram shows how to connect the reader to the controller in Wiegand mode. Figure 14: Wiegand wiring diagram Table 18: Wiegand wiring diagram Callout Description Mullion reader Single Gang reader Rear view of the reader Host controller Wiegand interface ioSmart Gen 1 Card Reader Installation Guide... -
Page 28: Wiegand Cat5 Wiring
Host controller Wiegand interface Connecting multiple readers to a controller Use this section to find out how to connect multiple readers to a controller using the daisy chain or the star wiring methods. ioSmart Gen 1 Card Reader Installation Guide... -
Page 29: Daisy Chain Wiring
Daisy chain wiring The following diagram shows the daisy chain wiring method to connect multiple readers to a controller. Figure 16: Daisy chain wiring diagram ioSmart Gen 1 Card Reader Installation Guide... -
Page 30: Star Wiring
Configuring the reader using the terminals Use this section to configure the reader using the terminals. Note: If RS-485 communication is not detected when you turn on the reader, it transmits Wiegand format according to its configuration. ioSmart Gen 1 Card Reader Installation Guide... -
Page 31: Factory Default (Ssf Transmission Format)
A simultaneous sequence of four beeps and flashes, four times, indicates a successful return to the SSF transmission format. A sequence of rapid beeps and flashes for 4 seconds indicates that the device has not returned to the SSF transmission format. ioSmart Gen 1 Card Reader Installation Guide... -
Page 32: Hard Reset (Ssf Transmission Format)
A simultaneous sequence of six beeps and flashes, four times, indicates a successful return to default configuration data. A sequence of rapid beeps and flashes for 4 seconds indicates that the device has not returned to default configuration data. ioSmart Gen 1 Card Reader Installation Guide... -
Page 33: 34-Bit Transmission Format
A simultaneous sequence of one beep and one flash, four times, indicates a successful config- uration to the 34-bit transmission format. A sequence of rapid beeps and flashes for 4 seconds indicates that the device is not config- ured to the 34-bit transmission format. ioSmart Gen 1 Card Reader Installation Guide... -
Page 34: 26-Bit Transmission Format
A simultaneous sequence of two beeps and flashes, four times, indicates a successful config- uration to the 26-bit transmission format. A sequence of rapid beeps and flashes for 4 seconds indicates that the device is not config- ured to the 26-bit transmission format. ioSmart Gen 1 Card Reader Installation Guide... -
Page 35: Sending The Unique Identifier (Uid)
A simultaneous sequence of five beeps and flashes, four times, indicates a successful configu- ration to the UID option. A sequence of rapid beeps and flashes for 4 seconds indicates that the device is not config- ured to the UID format. ioSmart Gen 1 Card Reader Installation Guide... -
Page 36: Configuring The Reader Using A Kantech Smartcard
Configuring the reader's OSDP address About this task: You can configure the reader's OSDP address by using the OSDP Programming Card and OSDP Address Card with the reader. Addresses are identified from numbers 1-10, 20, and 30. ioSmart Gen 1 Card Reader Installation Guide... -
Page 37: Compliance Specifications
• Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. ioSmart Gen 1 Card Reader Installation Guide... -
Page 38: Ce Compliance
IV, polybrominated biphenyl (PBB), and polybrominated diphenyl ether (PBDE) in electrical and electronic equipment. WEEE (Waste Electrical and Electronic Equipment) This regulation is used for waste electrical and electronic equipment, and addresses the disposal and the environmental handling of these products. © 2022 Johnson Controls. All rights reserved.
Need help?
Do you have a question about the ioSmart Gen 1 and is the answer not in the manual?
Questions and answers