Advertisement
4.2.
OPERATING
WARNING! Ensure you have read, understood and apply safety instructions.
4.2.1.
Connect the tool to the air supply.
4.2.2.
To start the tool, hold firmly and push the trigger locking lever forward whilst depressing trigger.
4.2.3.
The disc must be running at its maximum speed before attempting to cut the workpiece.
4.2.4.
Slowly and smoothly bring the cutting disc toward the workpiece (avoid jerky movements).
4.2.5.
Exert adequate pressure on the tool to allow cutting according to the type and size of the
material you are working with. Avoid subjecting disc to excessive strain, always hold tool
firmly and ease disc against workpiece (a harsh impact may break the disc). Maintain a
controlled progression.
DO NOT allow tool to free run for an extended period of time as this will shorten its life.
5.
MAINTENANCE
WARNING! Disconnect tool from air supply before changing accessories, servicing or
performing maintenance. Replace or repair damaged parts. Use genuine parts only.
Unauthorised parts may be dangerous and will invalidate the warranty.
5.1.
If the air supply does not have an oiler, lubricate the air tool daily with a few drops of Sealey
air tool oil dripped into the air inlet to prolong its life.
5.2.
Clean the tool after use.
5.3.
Loss of power or erratic action may be due to the following:
a) Excessive drain on the air line. Moisture or restriction in the air pipe. Incorrect size or
type of hose connectors. To remedy check the air supply and follow instructions in
chapter 3.
b) Grit or gum deposits in the tool may also reduce performance. If your model has
an air strainer (located in the area of the air inlet), remove the strainer and clean it. Flush
the tool out with gum solvent oil or an equal mixture of SAE No 10 oil and
paraffin. Allow to dry before use.
5.4.
For a full service contact your local Sealey service agent.
5.5.
When not in use, disconnect from air supply, clean tool and store in a safe, dry,
childproof location.
WARNING! The grinding process can produce streams of sparks (especially when grinding metal) which are a
potential source of ignition.
DO NOT use the grinder where there are flammable liquids, solids or gases.
DO NOT allow grinder sparks to make contact with the operator's clothing or any other fabric such as cleaning rags.
Fabrics contaminated with inflammable materials such as petrol, oil, grease, paint and solvents are a particular fire
hazard.
To reduce the risk of clothing catching fire the operator should wear wool or cotton outer garments treated with a fire
retardant in preference to man-made fibres.
Risk of Hand Arm Vibration Injury.
The SA650.V2 Air Cut-Off Tool 75mm Super Duty when operated in accordance with these instructions and tested in accordance
with EN 28662-2: 1994 results in the following vibration emission declared in accordance with BS EN12096: 1996.
Measured vibration emission value: .................... 2.5m/s²
These values are suitable for comparison with emission levels of other tools that have been subject to the same test.
This tool may cause hand-arm vibration syndrome if its use is inadequately managed.
Recommended Measures to reduce risk of hand-arm vibration syndrome: This item represents a low Hand Arm Vibration
risk to users. The calculated maximum usage period exceeds 8 hours. We recommend appropriate safety equipment is utilised
and regular breaks for the operator are employed to reduce any residual risk of fatigue or repetitive strain injury.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
DANGER OF FIRE/ExPLOSION HAzARD
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
Original Language Version
Uncertainty: ............................................. 1.0m/s²
01284 757500
01284 703534
www.sealey.co.uk
Web
sales@sealey.co.uk
email
SA650.V2
Issue: 3 - 18/11/10
Advertisement
