RAVEMEN PR2000 - Wireless Switch Control Headlight, 2000 Lumens Manual

Performance Parameters

Mode	Brightness level	Brightness (Lumens)	Run Time (hrs)	Max distance	Impact resistance	Waterproof
Road Biking	High	1000	2.2	170 meters	1 meter	Headlight: IPX8 Wireless switch: IPX4
	Mid	500	4.5
	Low	250	10
	Eco	100	25
	Rapid flashing	500	19
Mountain Biking	High	2000	1.1
	Mid	1000	2.2
	Low	500	4.5
Emergency	Turbo	2000	/

Notes:

1. The above data are tested in Lab in line with ANSI/NEMA FL1 standard and may vary by environment and user conditions;
2. To meet IPX8 waterproof standard, please make sure the tail USB caps are securely mounted before use.

Quick Guide

Pair the light with the wireless switch
Automatic pairing: Place the battery into the wireless switch, then turn on the light, and click any button on the wireless switch to control the light.
If no response, continue with the manual pairing steps below:

1. Keep the light on. Press and hold the power button and menu button of the light simultaneously for 5s until the LED display is flashing with "CC";
2. Press and hold the power button and menu button of the wireless switch simultaneously for 5s to connect with the light. When connected, the LED display will be flashing with "00"; if not, repeat this step.

Note: The working range between the light and the switch is around 3 meters.
After 3 days without operation, the wireless chip of the light will enter sleep mode and disconnect with the wireless switch. Turn on the light and it will connect with the wireless switch automatically.

Disconnect the light and the wireless switch permanently
Turn on the light, then press and hold the power button and menu button of the light simultaneously for 3 seconds.
Note: To pair with a new wireless switch, disconnect the light as mentioned above and then continue with the 1-2 steps in the pairing instruction.

Type-C input
Standard charging time: 3.3 hours (5 V, DC/2A), approximate values and may vary by user conditions; built-in over-charge protection. The screen will display "88" when charging is complete.

USB output
Max output: 5V, DC/2A; built-in over-discharge protection.

Runtime extension
The light can be powered by external power source(5V, DC/2A) to extend the runtime of the battery and the max output will be around 800 lumens.

Other features

1. Intelligent thermal management circuit to prevent overheat of LEDs.
2. Intelligent memory circuit remembers the last used brightness level and mode when turned on again.

Mounting Your Light

1. Select the suitable configuration for your handlebar:
   
2. Mount the handlebar mount and adjust the angle for actual needs, then tighten the screw with the hex key provided: (make sure the screw is completely tightened before riding)
   
3. Slide the headlight in the right direction to connect with the handlebar mount.
   
4. Press and hold the quick release tab and slide out the light.
   
5. Secure the wireless switch to the handlebar and control the light remotely:
   

Attention!
For your safety, please read this manual thoroughly and use your light accordingly.
Make sure the Light is mounted securely on the handlebar each time before riding.
Release the bike light from the handlebar mount while in the outdoors in case of theft.
To maintain the best performance and extending the life of the Lithium-ion battery:

1. Check the battery and charge the battery up before your first riding.
2. Avoid completely discharging, allow partial discharges and avoid over charging (usually).
3. Keep and storage your light at room temperature.
4. Charge your light to 50% full every 3 months for long term storage.
5. Make two complete charging and discharging cycle to calibrate the led display after long term storage.

Lithium-ion battery inside, don't put the light in a fire, otherwise it may cause explosion! Please charge the light with qualified USB power adapter. Using defective USB power adapter may cause power leakage or fire disaster, etc. Ravemen is not responsible for any of such consequences.

Technical Specifications

LED: 2*high-efficiency white LEDs
Battery: 6000mAh/3.7V rechargeable Lithium-ion battery
Dimensions (Headlight): 100mm (L)*48mm (W)*27mm (H)
Weight (Headlight): 214g
Package includes: front bike light*1, handlebar mount*1, thick silicone shim*1, thin silicone shim*1, USB cable*1, O ring *2; wireless switch*1 (Cr2032 battery*1)

• Keep button batteries out of reach of children. Never allow children to replace button batteries of any device.
• Swallowing may lead to serious or fatal injury in as little as 2 hours, due to chemical burns and potential perforation of the oesophagus.
• If you suspect your child has swallowed or inserted a button battery, immediately call or take them for emergency medical help.

Advice about the safe disposal of button/coin batteries

• Dispose of used button/coin batteries immediately.
• Place sticky tape around both sides of the battery and dispose of it immediately in an outside bin, out of reach of children, or recycle safely.

Website: www.ravemen.com
Tel/Fax: +86-755-29064166
Email: service@ravemen.com
Address: 501, Building A, Nankeng 2nd Industrial Park,
Bantian, Longgang, Shenzhen 518129, China

For your safety, read this manual thoroughly before using the product and keep it properly for future reference.
Scan and like our facebook page for more info and service: