BINMASTER VR-90 VIBRATING ROD Operating Instructions Manual

Vibrating level switch for granulated bulk relay (dpdt)

Hide thumbs Also See for VR-90 VIBRATING ROD:

Operating instructions manual (36 pages)

Table Of Contents

Table of Contents

Quick Links

Download this manual

Operating Instructions

Vibrating level switch for

granulated bulk relay (DPDT)

VR-90

VIBRATING ROD

Table of Contents

Need help?

Do you have a question about the VR-90 VIBRATING ROD and is the answer not in the manual?

Questions and answers

Summary of Contents for BINMASTER VR-90 VIBRATING ROD

Page 2: Table Of Contents
Dismounting steps......................26 Disposal ......................... 26 Supplement ..........................27 Technical data ........................ 27 Dimensions ........................30 Industrial property rights ....................33 Trademark ........................33 VEGAVIB 61 • Relay (DPDT) VR-90 Vibrating Rod | 925-0375 | ©2023 BinMaster all rights reserved...
Page 3 Safety instructions for Ex areas: Take note of the Ex specific safety instructions for Ex applications. These instructions are attached as documents to each instrument with Ex approval and are part of the operating instructions. Editing status: 2022-09-15 VEGAVIB 61 • Relay (DPDT) VR-90 Vibrating Rod | 925-0375 | ©2023 BinMaster all rights reserved...
Page 4: About This Document
The dot set in front indicates a list with no implied sequence. Sequence of actions Numbers set in front indicate successive steps in a procedure. Disposal This symbol indicates special instructions for disposal. VEGAVIB 61 • Relay (DPDT) VR-90 Vibrating Rod | 925-0375 | ©2023 BinMaster all rights reserved...
Page 5: For Your Safety
Arbi- trary conversions or modifications are explicitly forbidden. For safety reasons, only the accessory specified by the manufacturer must be used. To avoid any danger, the safety approval markings and safety tips on the device must also be observed. VEGAVIB 61 • Relay (DPDT) VR-90 Vibrating Rod | 925-0375 | ©2023 BinMaster all rights reserved...
Page 6: Safety Label On The Instrument
DIN EN ISO 14001. Please help us fulfil this obligation by observing the environmental instructions in this manual: • Chapter " Packaging, transport and storage" • Chapter " Disposal" VEGAVIB 61 • Relay (DPDT) VR-90 Vibrating Rod | 925-0375 | ©2023 BinMaster all rights reserved...
Page 7: Product Description
VEGAVIB 61 is a point level sensor with vibrating rod for point level detection. It is designed for industrial use in all areas of process technology and is preferably used for bulk solids. VEGAVIB 61 • Relay (DPDT) VR-90 Vibrating Rod | 925-0375 | ©2023 BinMaster all rights reserved...
Page 8: Adjustment
Your instrument was protected by packaging during transport. Its capacity to handle normal loads during transport is assured by a test based on ISO 4180. VEGAVIB 61 • Relay (DPDT) VR-90 Vibrating Rod | 925-0375 | ©2023 BinMaster all rights reserved...
Page 9 With instrument weights of more than 18 kg (39.68 lbs) suitable and Lifting and carrying approved equipment must be used for lifting and carrying. VEGAVIB 61 • Relay (DPDT) VR-90 Vibrating Rod | 925-0375 | ©2023 BinMaster all rights reserved...
Page 10: Mounting
To maintain the housing protection, make sure that the housing lid is closed during operation and locked, if necessary. VEGAVIB 61 • Relay (DPDT) VR-90 Vibrating Rod | 925-0375 | ©2023 BinMaster all rights reserved...
Page 11: Mounting Instructions
Mounting instructions Nozzle The vibrating element should protrude into the vessel to avoid buildup. For that reason, avoid using mounting bosses for flanges VEGAVIB 61 • Relay (DPDT) VR-90 Vibrating Rod | 925-0375 | ©2023 BinMaster all rights reserved...
Page 12 To compensate measurement errors caused by the material cone in cylindrical vessels, the sensor must be mounted at a distance of d/6 from the vessel wall. VEGAVIB 61 • Relay (DPDT) VR-90 Vibrating Rod | 925-0375 | ©2023 BinMaster all rights reserved...
Page 13 To achieve a very precise switching point, you can install the VR-90 the VR-90 Horizontal mounting To achieve a very precise switching point, you can install VEGAVIB 61 horizontally. However, if the switching point can have a tolerance of a VEGAVIB 61 • Relay (DPDT) VR-90 Vibrating Rod | 925-0375 | ©2023 BinMaster all rights reserved...
Page 14 In applications such as grit chambers or settling basins for coarse falling rocks sediments, the vibrating element must be protected against damage with a suitable baffle. This baffle must be manufactured by you. > 125 mm (> 5") Fig. 7: Baffle for protection against mechanical damage VEGAVIB 61 • Relay (DPDT) VR-90 Vibrating Rod | 925-0375 | ©2023 BinMaster all rights reserved...
Page 15: Connecting To Power Supply
Take note of the corresponding installation regulations for Ex applica- Connection cable tions. for Ex applications Cover all housing openings conforming to standard according to EN 60079-1. VEGAVIB 61 • Relay (DPDT) VR-90 Vibrating Rod | 925-0375 | ©2023 BinMaster all rights reserved...
Page 16: Connection Procedure
11. Screw the housing lid back on The electrical connection is finished. Wiring plan, single chamber housing The following illustrations apply to the non-Ex as well as to the Ex-d version. VEGAVIB 61 • Relay (DPDT) VR-90 Vibrating Rod | 925-0375 | ©2023 BinMaster all rights reserved...
Page 17 If inductive loads or stronger currents are switched through, the gold plating on the relay contact surface will be permanently damaged. The contact is then no longer suitable for switching low-voltage circuits. VEGAVIB 61 • Relay (DPDT) VR-90 Vibrating Rod | 925-0375 | ©2023 BinMaster all rights reserved...
Page 18 It is imperative that you take measures to extinguish sparks to protect the relay contact (e.g. Z diode) or use an electronic version with transistor output. VEGAVIB 61 • Relay (DPDT) VR-90 Vibrating Rod | 925-0375 | ©2023 BinMaster all rights reserved...
Page 20: Function Table
Dry run protection (6) (7) Relay energized Green Mode min. Dry run protection (6) (7) Relay deenergized Failure of the supply volt- (min./max. mode) (6) (7) Relay deenergized VEGAVIB 61 • Relay (DPDT) VR-90 Vibrating Rod | 925-0375 | ©2023 BinMaster all rights reserved...
Page 22: Maintenance And Fault Rectification
VEGA service hotline under the phone no. +49 1805 858550. The hotline is manned 7 days a week round-the-clock. Since we offer this service worldwide, the support is only available in the English language. The service is free, only standard call charges are incurred. VEGAVIB 61 • Relay (DPDT) VR-90 Vibrating Rod | 925-0375 | ©2023 BinMaster all rights reserved...
Page 23: Exchanging The Electronics Module
2. Unscrew the housing lid 3. Lift the opening levers of the terminals with a screwdriver 4. Pull the connection cables out of the terminals 5. Loosen the two screws with a screw driver (Torx size T10 or slot VEGAVIB 61 • Relay (DPDT) VR-90 Vibrating Rod | 925-0375 | ©2023 BinMaster all rights reserved...
Page 24: How To Proceed If A Repair Is Necessary
By doing this you help us carry out the repair quickly and without having to call back for needed information. VEGAVIB 61 • Relay (DPDT) VR-90 Vibrating Rod | 925-0375 | ©2023 BinMaster all rights reserved...
Page 25 Attach the completed form and, if need be, also a safety data sheet outside on the packaging • Ask the agency serving you to get the address for the return ship- ment. You can find the agency on our homepage. VEGAVIB 61 • Relay (DPDT) VR-90 Vibrating Rod | 925-0375 | ©2023 BinMaster all rights reserved...
Page 26: Dismount
If personal data is stored on the old device to be disposed of, delete it before disposal. If you have no way to dispose of the old instrument properly, please contact us concerning return and disposal. VEGAVIB 61 • Relay (DPDT) VR-90 Vibrating Rod | 925-0375 | ©2023 BinMaster all rights reserved...
Page 27: Supplement
Torque for NPT cable glands and Conduit tubes Ʋ Plastic housing max. 10 Nm (7.376 lbf ft) Ʋ Aluminium/Stainless steel housing max. 50 Nm (36.88 lbf ft) VEGAVIB 61 • Relay (DPDT) VR-90 Vibrating Rod | 925-0375 | ©2023 BinMaster all rights reserved...
Page 28 VEGAVIB 61 of 316L -50 … +150 °C (-58 … +302 °F) Process temperature (thread or flange -50 … +250 °C (-58 … +482 °F) temperature) with temperature adapter (option) VEGAVIB 61 • Relay (DPDT) VR-90 Vibrating Rod | 925-0375 | ©2023 BinMaster all rights reserved...
Page 29 Altitude above sea level up to 5000 m (16404 ft) 1) Max. 20 mm (0.8 in) with product density < 0.03 g/cm³ (0.0011 lbs/in³). VEGAVIB 61 • Relay (DPDT) VR-90 Vibrating Rod | 925-0375 | ©2023 BinMaster all rights reserved...
Page 30: Dimensions
½ NPT Fig. 15: Housing versions Plastic single chamber Stainless steel single chamber (electropolished) Stainless steel single chamber (precision casting) Aluminium - single chamber VEGAVIB 61 • Relay (DPDT) VR-90 Vibrating Rod | 925-0375 | ©2023 BinMaster all rights reserved...
Page 31 Fig. 16 VR-90 G1½ ø 29 mm (1.14") ø16 mm (0.63") Fig. 17: VEGAVIB 61, threaded version G1½ (DIN ISO 228/1) Fig. 17 VR-90 VEGAVIB 61 • Relay (DPDT) VR-90 Vibrating Rod | 925-0375 | ©2023 BinMaster all rights reserved...
Page 33: Industrial Property Rights
собственность. Дальнейшую информацию смотрите на сайте www.vega.com. VEGA系列产品在全球享有知识产权保护。进一步信息请参见网站< www.vega.com。 Trademark All the brands as well as trade and company names used are property of their lawful proprietor/ originator. VEGAVIB 61 • Relay (DPDT) VR-90 Vibrating Rod | 925-0375 | ©2023 BinMaster all rights reserved...
Page 36 Phone: 402-434-9102 VEGA Grieshaber KG 7201 N 98th St Fax: 402-434-9133 Am Hohenstein 113 Phone +49 7836 50-0 Lincoln, NE 68507 77761 Schiltach E-mail: info.de@vega.com Email: info@binmaster.com Germany www.vega.com www.binmaster.com VR-90 Vibrating Rod | 925-0375 | ©2023 BinMaster all rights reserved...

BINMASTER VR-90 VIBRATING ROD Operating Instructions Manual

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for BINMASTER VR-90 VIBRATING ROD

Summary of Contents for BINMASTER VR-90 VIBRATING ROD

Table of Contents