Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DINKO Instruments 1.9745.00
Summary of Contents for DINKO Instruments 1.9745.00
- Page 1 VARIABLE FLOW PERISTALTIC PUMPS WITH TIMER Model D-25VT 153-3r Codes 1.9745.00, 1.9745.11 and 1.9745.50 MANUAL June 2023 Marked c/ Encarnació , 123 -125. Tel. +34 93 284 69 62. Fax +34 93 210 43 07 E-mail: dinter@dinko.es www.dinko.es 08024 - Barcelona...
-
Page 2: Table Of Contents
INDEX Page Introduction ········································································································ 3 Packing list ········································································································· 3 Reception ··········································································································· 3 Description ········································································································· 5 Specifications ····································································································· 7 Start up ·············································································································· 8 Digital timer ········································································································ 9 Accessories ····································································································· 15 Tube change ····································································································· 17 Ordering information ························································································· 19 Changing fuses ································································································· 19 Troubleshooting ································································································... -
Page 3: Introduction
Flow rates are obtained from 0.02 ml/minute up to 5000 ml/minute. A large number of different size tubes or hoses made of materials resistant to various substances are available. 2- PACKING LIST Code Quantity D-25VT pump 1.9745.00 / 1.9745.11/ 1.9745.50 Set tubes Power cord Footswitch connector Instruction Manual... - Page 4 3.6- SIGNS AND SYMBOLS Always pay attention to the danger warning signs and symbols that will appear in this manual or on labels attached to the body of the Pump such as those shown below. SIGNS/ SYMBOLS INTERPRETATION-MEANING Avoid finger contact with moving parts Danger-Risk-Caution Before opening DISCONNECT...
-
Page 5: 4- Description
4- DESCRIPTION The D-25Vplus peristaltic pumps in this manual mount the 153-3r head that allows easy access to the tube for removal when it must be replaced. On the 153-3r easy-load head, simply pull up and to the left of the lever (1) located on the top of the head to raise the top and open the head for tube replacement. - Page 6 4-2 FRONT PANEL Figure a 1- Cyclic timer 2- Numerical speed control 3- Engine crank and stop selector 4- Pilot lamp 5- FULL peak flow push button 4-3 REAR PANEL Figure b 7- ON/OFF main power switch 8- Fuse box 9- Power socket 10- Timing mode selector 11- Input for voltage-free pedal...
-
Page 7: 5- Specifications
8.0 mm Code Head 0.5 mm 0.8 mm 1.6 mm 3.2 mm ◄Tube Ø 1.9745.11 0.17-2.8 0.5-6.7 2.7-28 6.7-100 19-230 27-367 58-500 Flow ml/min 1.9745.00 153-3r 0.5-8.5 1.5-20 8.0-85 20-330 56-700 80-1050 175-1300 1.9745.50 0.7-12 2-29 12-120 29-470 80-1000 115-1500 250-2000 The indicated flows are approximate and refer to liquids with a viscosity like water at normal temperature and without discharge back pressure. -
Page 8: 6- Start Up
6- START UP INITIAL CONSIDERATION: For a correct dosing with a Peristaltic Pump with a timer, first of all you have to select the appropriate tube, both in composition and measurements to carry out the dosing of the desired volume. Tests must always be carried out to determine how much volume is dosed per unit of time. -
Page 9: 7- Digital Timer
7- TIMER When the equipment is connected, the timer starts and waits. To start it, press the ▲ key (6) 1- OUT Open/closed contact indicator-red pilot 2 - Measured time (red) 3 - Scheduled time (green) 4 -Time units (hour-minute-second) H/M/S-pilot green button. - Page 10 Menu sequence- Factory programming i nt Pressing ▲ selects Select response time 1 mS 20ms Press Select the menu you want use. Pressing ▲ selects Description of the different modes in the section 7.3 Modes of use n (N Mode ) F (F Mode) C (C Mode) r (R Mode)
- Page 11 7-2 Selection of operation and stop time. The timer has two programming times t.oFF and t.on indicating the status of the timer contacts. t.oFF will always be the first to count and then t.on will count . N, F modes we can only program the t.oFF , instead in the R mode , we must configure the t.oFF and he t.on . To enter the time selection menu, press ►.
- Page 12 7.3 Modes of use The pump has a timing mode selector on the back with two positions, O and I. (Figure b (10)). In position O , when the timer starts (by pressing the ▲ key of the timer, it will start counting the programmed times), the head will work for the time programmed as t.oFF .
- Page 13 When you want to program a single dosage with a delay; that is, when the timer is activated, it will count the programmed time with the head stopped and at the end of said time the head will start up, it will work until the equipment stops.
- Page 14 7.3.c- R mode Asymmetric cyclical mode, in which an operating time and a stop time are programmed to repeat indefinitely. This working mode is used for: When we want to carry out a repetitive dosing of a specific volume, having a stop time between dosing and dosing, to be able to place the rubber in another container to do another dosing.
-
Page 15: 8- Accessories
8- ACCESSORIES 8.1 Balance for flow and dosage calibration. Reproducibility 0,1 g. 600g capacity. Code 1.9812.02 To measure the quantity dosed in the Calibration process of peristaltic pumps, it is very effective to use a precision balance with digital reading. If the liquid to be pumped has density "1"... - Page 16 CONNECTORS FOR PERISTALTIC TUBES 8.5 Reducing Splice Connectors / Same Ends, Polypropylene For tubes 1,6/3,2mm. ID. Code1.0080.15 For tubes 3,2/4,8mm. ID. Code 1.0080.18 For tubes 4,8/6,4mm ID. Code 1.0080.05 For tubes 6,4/8mm ID. Code 1.0080.14 For tubes 8/12,7mm ID. Code 1.0080.20 8.6 Straight connector for fitting/reducer, polypropylene Straight connector / reducer Ø...
-
Page 17: 9- Tube Change
9- CHANGE OF TUBES Each pump is supplied with a set of medical/food grade silicone peristaltic tubes according to FDA and USP standards, autoclavable at 120ºC, with peristaltic use range up to 80ºC and medium duration. The peristaltic quality of the tubes or rubber consists of their ability to quickly recover their roundness once the rollers of the peristaltic head of the pump have compressed it to generate the circulation of liquids inside. - Page 18 9.1 AVAILABLE TUBES PHARMA Autoclavable multiple times. ETO and Gamma sterilizable. Medical-food grade, class VI USP, 21CFR 177.2600 and FDA. Not hemolytic. Excellent resistance to chemicals. ISO 10993. Low permeability and good resistance to abrasion. Long duration. Use temperature, -51ºC to 132ºC Beige.
-
Page 19: 10- Ordering Information
10- ORDERING INFORMATION Peristaltic pump head 153V-3r. For 1.6mm wall tubes. Model D-25VT. Code: 1.9745.00 and 1.9745.11 11- CHANGE FUSES The fuse box is part of the power base located at the rear of the pump. See Figure. main switch... -
Page 20: 13- Maintenance - Spare Parts
Before any examination or repair of the appliance, it is necessary to disconnect the mains plug. Any initiative must be carried out by qualified personnel to avoid greater evils. Entrust your device to a technical service authorized by DINKO Instruments. The engine and its block do not require greasing, so they don’t have maintenance. -
Page 21: 14- Warranty
14- WARRANTY DURATION: The guarantee is established for a period of 1 year from the date of commissioning of the device, provided that the warranty card is returned to us within 8 days of said commissioning. Without this condition the guarantee will not be valid. -
Page 22: 15- Ec Declaration
15-EC DECLARATION OF CONFORMITY DINTER SA / DINKO Instruments c/ Encarnació, 123-125 / 08024 - Barcelona Declares that the items mentioned in the attached list, to which this declaration refers, comply with the essential safety requirements of the applicable European Directive:... - Page 23 OTHER DINKO APPARATUS - Blenders-Homogenizers - Colorimeters - Conductivity Meters - Dosing Pumps - Extractor for meat analysis - Heating Plates - Infrared Stoves - Kits for water analysis - Magnetic Stirrers - Metallic block heaters - Microscopes - Nephelometers - Orbital Shakers - Oximeters - Peristaltic Pumps...
Need help?
Do you have a question about the 1.9745.00 and is the answer not in the manual?
Questions and answers