Table of Contents
Advertisement
First Time Installation
When turned on for the first time, the language
selection screen will be displayed. Select the desired
language and press OK.
On the next screen, set your country preference and
press OK to continue.
You will be asked to set and confirm a PIN at this point.
For some Country options, the PIN cannot be set to
0000, in this case you need to enter another 4-digit
number combination.
The Signage Settings menu will be displayed next.
Set ID, OSD Orientation, Auto software update
options can be configured using this menu. Model
name, Serial number and Software version options
are for information only. They will be grayed out and
not selectable. Please note this information as it
will be required if contacting Toshiba regarding
your monitor refer to the Signage Settings Menu
Contents section for more information on the options
of this menu. While this menu is displayed on the
screen you can copy database files from a connected
USB device to the Display by pressing the Yellow
button. You can also save the model information data
of the Display to a connected USB device by pressing
the Blue button. After the settings are completed,
press OK to continue.
On the next screen, the Network/Internet Settings
menu will be displayed. Please refer to Connectivity
section to configure a wired or a wireless connection.
After the settings are completed press OK button to
continue.
The First Time Installation is completed.
To repeat this process and reset the Display's settings
to the factory defaults enter the Signage Settings
menu, highlight First time installation and press
OK. You will be asked to enter the PIN that you have
defined in the First Time Installation. If the correct PIN
is entered a confirmation message will be displayed
asking whether you want to delete all settings and
reset the Display. Select Yes and press OK to confirm.
Note: Do not turn off the Display while initializing first time
installation. Note that, some options may not be available
depending on the country selection.
Media Playback via USB Input
If internal USB device is inserted and external device is also
inserted, media player will use the external device only. You
can connect 2.5" and 3.5" inch (hdd with external power
supply) external hard disk drives or USB memory stick to your
Display by using the USB input/s of the Display.
IMPORTANT! Back up the files on your storage
devices before connecting them to the Display.
Manufacturer will not be responsible for any file
damage or data loss. Certain types of USB devices
(e.g. MP3 Players) or USB hard disk drives/memory
sticks may not be compatible with this Display. The
Display supports FAT32 and NTFS disk formatting.
Wait a little while before each plugging and unplugging
as the player may still be reading files. Failure to do
so may cause physical damage to the USB player
and the USB device itself. Do not pull out your drive
while playing a file.
You can use USB hubs with your Display's USB
input/s. External power supplied USB hubs are
recommended in such a case.
It is recommended to use the Display's USB input/s
directly, if you are going to connect a USB hard disk.
Note: When viewing image files the Media Browser menu
can only display 1000 image files stored on the connected
USB device.
Media Browser Menu
You can play photo, music and movie files stored on
a USB disk by connecting it to your Display. Connect
a USB disk to one of the USB inputs located on the
side of the Display. Pressing the Menu button while
in the Media Browser mode will access the Picture,
Sound and Settings menu options. Pressing the
Menu button again will exit from this screen. You
can set your Media Browser preferences by using
the Settings menu.
Start playback with the Play
button and activate
Start playback with the OK but-
ton and activate
Start playback with the Play
button and activate
Start playback with the Play
button and activate
USB
Auto Play
Note: USB autoplay function will only operate from
AC cycle or if Quick standby is disabled".
USB AutoPlay feature is to start playing the media
content in removable device, automatically. It uses
the Media Browser. The media content types have
different priorities in order to be played. The reducing
priority order is as Photo, Video and Audio. That
means, if there is Photo content in the root directory
of the removable device, MediaBrower will play the
Photos in a sequence (in file name order) instead of
Video or Audio files. If not, it will be checked for Video
content and as last Audio.
But if the user presses the Exit button to go out from
Media Browser, Display will go back to the previous
source and will display the content.
This feature will only work if all of the following cir-
cumstances occur:
English - 11 -
Loop/Shuffle Mode Operation
All files in the list will be contin-
uously played in original order
The same file will be played
continuously (repeat)
All files in the list will be played
once in random order
All files in the list will be con-
tinuously played in the same
,
random order.
Feature
Advertisement
Table of Contents
