Related Manuals for LD DIO 04
Summary of Contents for LD DIO 04
- Page 1 USER´S MANUAL BEDIENUNGSANLEITUNG MANUEL D´UTILISATION MANUAL DE USUARIO INSTRUKCJA OBSŁUGI MANUALE D´USO DIO 04 4 OUTPUT DANTE INTERFACE LDDIO04...
-
Page 2: Table Of Contents
MANUAL DE USUARIO COMPLETO / KOMPLETNY PODRĘCZNIK UŻYTKOWNIKA / MANUALE D‘USO COMPLETO DIO 04 USER MANUAL ONLINE Scan this QR Code to get to the download section of DIO 04. Here you can get the complete User manual in the following languages: EN, DE, FR, ES, PL, IT www.ld-systems.com/LDDIO04-downloads... -
Page 3: Information On This Short Manual
This device was developed and manufactured under high quality requirements to ensure many years of trouble-free operation. This is what LD Systems stands for with its name and many years of experience as a manufacturer of high-quality audio products. Please read these operating instructions carefully so that you can quickly and optimally use your new LD Systems product. -
Page 4: Safety Instructions
This symbol indicates hazards that can cause an electric shock. This symbol indicates danger spots or dangerous situations. This symbol indicates danger from hot surfaces. This symbol indicates danger from high volumes. This symbol indicates supplementary information on the operation of the product. This symbol denotes a device that does not contain any user-serviceable parts. - Page 5 DANGER: 1. Do not operate the device if it has been exposed to severe temperature fluctuations (e.g. after transport). Humidity and condensation could damage the device. Do not switch on the device until it has reached the ambient temperature. 2. Make sure that the voltage and frequency of the mains supply correspond to the values indicated on the device.
-
Page 6: Notes For Indoor Installation Equipment
DANGER: 1. Do not install or operate the device near radiators, heat registers, stoves or other heat sources. Make sure that the device is always installed in such a way that it is sufficiently cooled and cannot overheat. 2. Do not place any sources of ignition such as burning candles near the device. 3. -
Page 7: Packaging Content
• User manual INTRODUCTION Part of the TICA® series, the DIO 04 is a four output Dante interface that delivers the capabilities that audio and AV professionals really need. Equipped with four balanced outputs to connect to any analogue audio device such as power amplifiers Signal presence lights on each channel speed installation and fault-finding. -
Page 8: Connections, Operating And Display Elements
Dante® interface with RJ45 socket for connecting further Dante® devices to the Dante® network. If the DIO 04 is supplied with power via an external power supply unit, another DIO 04 can be supplied with power via PoE (see connection example 2). -
Page 9: Connection Examples
POWER SYMBOL As soon as the DIO 04 is supplied with voltage, the starting process begins. During the start-up process, the white power symbol flashes and the line outputs OUTPUT 1 to 4 are muted. When the start-up process is completed after a few seconds, the symbol lights up permanently and the unit is ready for operation. - Page 10 Power supply Ethernet Switch 24V DC Power supply Dante Mixer ™ INPUTS OUTPUTS POWER NETWORK REMOTE ZONE X 1208D INPUTS touch control wall panel Ethernet Switch ZONE X 1208D QTP 8 OUTPUT 1 - 4 touch control wall panel Ethernet Switch Dante®...
-
Page 11: Terminal Block Connections
TERMINAL BLOCK CONNECTIONS OUTPUT connections balanced unbalanced When wiring terminal blocks, please observe the correct assignment of the poles/ terminals. The manufacturer accepts no liability for damage caused by faulty wiring! -
Page 12: Dante® Controller
The settings in the units in the network are retained. When the DIO 04 is disconnected from the Dante® network, the unit's audio outputs are muted and the power icon on the front panel starts flashing. -
Page 13: Under / On-Table Mounting
UNDER / ON-TABLE MOUNTING There are two recesses on the top and bottom of the enclosure, each with two M3 threaded holes, for mounting underneath or on top of the table. Screw the two enclosed mounting plates to the top or bottom using the enclosed M3 countersunk screws. Now the amplifier can be fixed in the desired position (see illustration, fixing screws not included). -
Page 14: Dimensions (Mm)
1. Housing surfaces must be cleaned with a clean, damp cloth. Make sure that no moisture can penetrate the unit. 2. Air inlets and outlets must be regularly cleaned of dust and dirt. If compressed air is used, make sure that damage to the unit is prevented (e.g. fans must be blocked in this case). 3. -
Page 15: Technical Data
TECHNICAL DATA Item number LDDIO04 Product type 0x4 I/O Dante Interface Inputs Input type Switchable balanced mic or line level Line outputs Output type Balanced line level with auto mute relay on loss of Dante/AES67 signal Cooling Convection Analogue Line Output Number of output connectors Connection type 3-pin terminal block, Pitch 3.81 mm... -
Page 16: Disposal
Item number LDDIO04 General Material Steel chassis, Plastic front panel Dimensions (W x H x D) 142 x 53 x 221 mm (height with rubber feet) Weight 1.0 kg Included Accessories Mounting plates for surface mount applications, Terminal blocks for Electrical Connections, rubber feet DISPOSAL Packaging: 1. -
Page 17: Manufacturer´s Declarations
MANUFACTURER´S DECLARATIONS MANUFACTURER‘S WARRANTY & LIMITATIONS OF LIABILITY Adam Hall GmbH, Adam-Hall-Str. 1, D-61267 Neu Anspach / E-mail Info@adamhall.com / +49 (0)6081 / 9419-0. Our current warranty conditions and limitation of liability can be found at: https://cdn-shop.adamhall.com/media/pdf/MANUFACTURERS-DECLARATIONS_LD_SYSTEMS.pdf. Contact your distribution partner for service. UKCA-CONFORMITY Hereby, Adam Hall Ltd. -
Page 18: Informationen Zu Dieser Kurzanleitung
LD-SYSTEMS.COM Adam Hall GmbH | Adam-Hall-Str. 1 | 61267 Neu-Anspach | Germany Phone: +49 6081 9419-0 | adamhall.com SHORT Adam Hall Ltd. | The Seedbed Business Centre | SS3 9QY Essex | UK REV: 01...
Need help?
Do you have a question about the DIO 04 and is the answer not in the manual?
Questions and answers