Related Manuals for Asus AAEON AEC-6613
Summary of Contents for Asus AAEON AEC-6613
- Page 1 All manuals and user guides at all-guides.com AEC-6613 Fanless Embedded Box PC User‟s Manual 4 Last Updated: December 31, 2015...
- Page 2 All manuals and user guides at all-guides.com Copyright Notice This document is copyrighted, 2015. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer.
- Page 3 All manuals and user guides at all-guides.com Acknowledgement All other products‟ name or trademarks are properties of their respective owners. Microsoft Windows is a registered trademark of Microsoft Corp. Intel, Pentium, Celeron, and Xeon are registered trademarks of Intel Corporation ...
- Page 4 All manuals and user guides at all-guides.com Packing List Before setting up your product, please make sure the following items have been shipped: Item Quantity BOXER-6613 Phoenix power connector Screw package Heat spreader Wall mount brackets ...
- Page 5 All manuals and user guides at all-guides.com About this Document This User‟s Manual contains all the essential information, such as detailed descriptions and explanations on the product‟s hardware and software features (if any), its specifications, dimensions, jumper/connector settings/definitions, and driver installation instructions (if any), to facilitate users in setting up their product.
- Page 6 All manuals and user guides at all-guides.com Safety Precautions Please read the following safety instructions carefully. It is advised that you keep this manual for future references All cautions and warnings on the device should be noted. All cables and adapters supplied by AAEON are certified and in accordance with the material safety laws and regulations of the country of sale.
- Page 7 All manuals and user guides at all-guides.com As most electronic components are sensitive to static electrical charge, be sure to ground yourself to prevent static charge when installing the internal components. Use a grounding wrist strap and contain all electronic components in any static-shielded containers.
- Page 8 All manuals and user guides at all-guides.com FCC Statement This device complies with Part 15 FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation.
- Page 9 All manuals and user guides at all-guides.com China RoHS Requirements (CN) 产品中有毒有害物质或元素名称及含量 AAEON Embedded Box PC/ Industrial System 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) 印刷电路板 ○ ○ ○ ○ ○ ○ 及其电子组件 外部信号...
- Page 10 All manuals and user guides at all-guides.com China RoHS Requirement (EN) Poisonous or Hazardous Substances or Elements in Products AAEON Embedded Box PC/ Industrial System Poisonous or Hazardous Substances or Elements Hexavalent Polybrominated Polybrominated Component Lead Mercury Cadmium Chromium Biphenyls Diphenyl Ethers (Pb) (Hg)
-
Page 11: Table Of Contents
All manuals and user guides at all-guides.com Table of Contents Chapter 1 - Product Specifications ..................1 Specifications ......................2 Chapter 2 – Hardware Information ..................4 Dimensions ....................... 5 Jumpers and Connectors ..................11 List of Jumpers ....................... 13 List of Connectors .................... - Page 12 All manuals and user guides at all-guides.com 3.4.5.1 Super IO Configuration: Serial Port 2 Configuration . 40 3.4.6 Advanced: Smart Fan Function ..........42 3.4.7 Advanced: H/W Monitor ............. 43 Setup submenu: Chipset..................44 3.5.1 Chipset: Host Bridge ..............45 3.5.1.1 Chipset: IGD Configuration ..........
-
Page 13: Chapter 1 - Product Specifications
All manuals and user guides at all-guides.com Chapter 1 Chapter 1 - Product Specifications... -
Page 14: Specifications
All manuals and user guides at all-guides.com Specifications System ® Intel Atom D2550 1.86 GHz Memory DDR3 800/1066 SODIMM x 1, up to 4 GB) VGA x 1 (optional 2 VGA) Ethernet Gigabit Ethernet, RJ-45 connector x 2 ... - Page 15 All manuals and user guides at all-guides.com Net Weight 2.16 kg (4.75 lb) Environmental No Airflow: Operating Temperature 0 ~ 50°C (32 ~ 122°F) - HDD 0 ~ 55°C (32 ~ 131°F) - CFast™ Card Ambient with Airflow: 0 ~ 55°C (32 ~ 131°F) - HDD 0 ~ 60°C (32 ~ 140°F) - CFast™...
-
Page 16: Chapter 2 - Hardware Information
All manuals and user guides at all-guides.com Chapter 2 Chapter 2 – Hardware Information... -
Page 17: Dimensions
All manuals and user guides at all-guides.com Dimensions Model A1 CFast Chapter 2 – Hardware Information... - Page 18 All manuals and user guides at all-guides.com Model A1M CFast Chapter 2 – Hardware Information...
- Page 19 All manuals and user guides at all-guides.com Model A2 CFast Chapter 2 – Hardware Information...
- Page 20 All manuals and user guides at all-guides.com Model A2M CFast Chapter 2 – Hardware Information...
- Page 21 All manuals and user guides at all-guides.com Model A3/A4 CFast AEC-6613 -A3 AEC-6613 -A4 Chapter 2 – Hardware Information...
- Page 22 All manuals and user guides at all-guides.com Model A3M/A4M CFast AEC-6613 -A3M AEC-6613 -A4M Chapter 2 – Hardware Information...
-
Page 23: Jumpers And Connectors
All manuals and user guides at all-guides.com Jumpers and Connectors Component Side Chapter 2 – Hardware Information... - Page 24 All manuals and user guides at all-guides.com Solder Side Chapter 2 – Hardware Information...
-
Page 25: List Of Jumpers
All manuals and user guides at all-guides.com List of Jumpers Please refer to the table below for all of the system‟s connectors that you can configure for your application Label Function Auto Power Button Selection Clear CMOS COM2 RI/+5/+12V Selection Touch Screen 4/5/8-wires Mode Selection Brightness Control for 2nd LVDS 2nd LVDS Backlight Bias/PWM Mode Selection... -
Page 26: List Of Connectors
All manuals and user guides at all-guides.com List of Connectors Please refer to the table below for all of the system‟s connectors that you can configure for your application Label Function Front Panel External +5VSB Input CPU FAN +5VSB Output w/ SMBus SATA Port External 12V Input Digital I/O... - Page 27 All manuals and user guides at all-guides.com CN24 2nd LVDS Inverter CN25 Stereo-L Channel CN26 1st LVDS Inverter CN27 1st LVDS (Single channel 18/24bit) CN28 2nd RJ-45 Ethernet CN29 1st RJ-45 Ethernet CN30 USB Port #1 and #2 CN31 Audio Line In/Out and MIC CN32 CRT/DVI (Configured by manufacturing) CN33...
-
Page 28: Com2 Port #4 (Cn16)
All manuals and user guides at all-guides.com 2.4.1 COM2 Port #4 (CN16) Signal Signal DCDD DTRD Ground DSRD RTSD CTSD 2.4.2 COM2 Port #3 (CN18) Signal Signal DCDC DTRC Ground DSRC RTSC CTSC 2.4.3 COM2 Port #2 (CN20) RS-232 Signal Signal DCDB DTRB... -
Page 29: Rcom Port #1 (Cn33)
All manuals and user guides at all-guides.com Ground DSRB RTSB CTSB RIB/+5V/(+12V) RS-422 Signal Signal TXD- RXD+ TXD+ RXD- Ground N/C / +5V / (+12V) RS-485 Signal Signal TXD- TXD+ Ground N/C / +5V / (+12V) 2.4.4 RCOM Port #1 (CN33) Signal Signal DCDA... -
Page 30: Cfast™ Card Installation
All manuals and user guides at all-guides.com CFast™ Card Installation Step 1: Install the CFast™ card. Step 2: Lower the arm to secure. Chapter 2 – Hardware Information... -
Page 31: Hard Disk Drive Installation (Model A1M/A2M)
All manuals and user guides at all-guides.com Hard Disk Drive Installation (Model A1M/A2M) Step 1: Open the base of AEC-6613 by removing the screws. Step 2: Get the Hard Disk Drive ready. Chapter 2 – Hardware Information... - Page 32 All manuals and user guides at all-guides.com Step 3: Place the HDD on the bracket and secure with screws Step 4: Connect the SATA and power cables to the HDD. Chapter 2 – Hardware Information...
- Page 33 All manuals and user guides at all-guides.com Step 5: Place the assembled HDD back into the device and secure with screws. Chapter 2 – Hardware Information...
-
Page 34: Sdram Installation
All manuals and user guides at all-guides.com SDRAM Installation Step 1: Remove the stands and base to access the interior Chapter 2 – Hardware Information... - Page 35 All manuals and user guides at all-guides.com Step 2: Remove the highlighted screws to remove the front panel Chapter 2 – Hardware Information...
- Page 36 All manuals and user guides at all-guides.com Step 3: Insert the SDRAM to the memory slot, push down to secure Chapter 2 – Hardware Information...
- Page 37 All manuals and user guides at all-guides.com Step 4: Place a heat-spreading sheet onto the SDRAM. Chapter 2 – Hardware Information...
-
Page 38: Din Rail Installation
All manuals and user guides at all-guides.com DIN Rail Installation Step 1: Attach the DIN Rail kit onto the chassis as shown below. Step 2: Slide a DIN Rail into the DIN Rail kit to check installation Chapter 2 – Hardware Information... -
Page 39: Wallmount Kit Installation
All manuals and user guides at all-guides.com Wallmount Kit Installation To attach the wallmount kit on to the AEC-6613, tightens the screws as shown in the diagram below. We suggest using this screw. Chapter 2 – Hardware Information... -
Page 40: Chapter 3 - Ami Bios Setup
All manuals and user guides at all-guides.com Chapter 3 Chapter 3 - AMI BIOS Setup... -
Page 41: System Test And Initialization
All manuals and user guides at all-guides.com System Test and Initialization The system uses certain routines to perform testing and initialization. If an error, fatal or non-fatal, is encountered, a few short beeps or an error message will be outputted. The board can usually continue the boot up sequence with non-fatal errors. -
Page 42: Ami Bios Setup
All manuals and user guides at all-guides.com AMI BIOS Setup The AMI BIOS ROM has a pre-installed Setup program that allows users to modify basic system configurations, which is stored in the battery-backed CMOS RAM and BIOS NVRAM so that the information is retained when the power is turned off. To enter BIOS Setup, press <Del>... -
Page 43: Setup Submenu: Main
All manuals and user guides at all-guides.com Setup Submenu: Main Options summary: (default setting) System Date Day MM:DD:YYYY Change the month, year and century. The „Day‟ is changed automatically. System Time HH : MM : SS Change the clock of the system. Chapter 3 –... -
Page 44: Setup Submenu: Advanced
All manuals and user guides at all-guides.com Setup Submenu: Advanced Options summary: (default setting) ACPI Settings System ACPI Parameters CPU Configuration CPU Configuration Parameters SATA Configuration SATA Device Options Settings USB Configuration USB Configuration Parameters Super IO Configuration IT8783 Super IO Configuration Parameters Chapter 3 –... - Page 45 All manuals and user guides at all-guides.com Smart Fan Function Smart Fan Function settings H/W Monitor Monitor hardware status Chapter 3 – AMI BIOS Setup...
-
Page 46: Advanced: Acpi Settings
All manuals and user guides at all-guides.com 3.4.1 Advanced: ACPI Settings Options summary: (default setting) Suspend Disabled ACPI Sleep State S3 (Suspend to RAM) Select the ACPI state used for System Suspend Chapter 3 – AMI BIOS Setup... -
Page 47: Advanced: Cpu Computing
All manuals and user guides at all-guides.com 3.4.2 Advanced: CPU Computing Options summary: (default setting) Hyper-Threading Disabled Enabled CPU Hyper-Threading Technology support or not Chapter 3 – AMI BIOS Setup... -
Page 48: Advanced: Sata Configuration
All manuals and user guides at all-guides.com 3.4.3 Advanced: SATA Configuration Options summary: (default setting) SATA Controller(s) Enabled Disabled SATA Controller Enable/Disable SATA Mode AHCI Configure SATA controller operating as IDE/AHCI mode. SATA PORTx Enabled Disabled Enable / Disable SATA Portx SATA Portx Hot Plug Enabled Chapter 3 –... -
Page 49: Advanced: Usb Configuration
All manuals and user guides at all-guides.com Disabled Enable / Disable SATA Portx Hot Plug function 3.4.4 Advanced: USB Configuration Options summary: (default setting) Legacy USB Support Enabled Disabled Auto Enables BIOS Support for Legacy USB Support. When enabled, USB can be functional in legacy environment like DOS. - Page 50 All manuals and user guides at all-guides.com (Emulation Type) Floppy Forced FDD Hard Disk CD-ROM If Auto. USB devices less than 530MB will be emulated as Floppy and remaining as Floppy and remaining as hard drive. Forced FDD option can be used to force a HDD formatted drive to boot as FDD(Ex.
-
Page 51: Advanced: Super Io Configuration
All manuals and user guides at all-guides.com 3.4.5 Advanced: Super IO Configuration Options summary: (default setting) Serial Port x Configuration Set Parameters of Serial Port x Parallel Port Configuration Set Parallel Port Configuration Restore AC Power Loss Power off Power on Last State Set Power on after power fail function Chapter 3 –... -
Page 52: Super Io Configuration: Serial Port 2 Configuration
All manuals and user guides at all-guides.com 3.4.5.1 Super IO Configuration: Serial Port 2 Configuration Options summary: (default setting) Serial Port Disabled Enabled En/Disable specified serial port. Change Settings Auto IO=2F8h; IRQ=3; IO=3F8h; IRQ=3,4,5,7,10,11,12; IO=2F8h; IRQ=3,4,5,7,10,11,12; IO=3E8h; IRQ=3,4,5,7,10,11,12; IO=2E8h; IRQ=3,4,5,7,10,11,12; Select a resource setting for Super IO device. - Page 53 All manuals and user guides at all-guides.com COM2 Type Option RS232 RS422 RS485 Configure COM2 operated as RS232, RS422 or RS485. Chapter 3 – AMI BIOS Setup...
-
Page 54: Advanced: Smart Fan Function
All manuals and user guides at all-guides.com 3.4.6 Advanced: Smart Fan Function Options summary: (default setting) Smart Fan 1 Mode Full on mode Automatic Mode Manual Mode Smart Fan 1 Mode Select Chapter 3 – AMI BIOS Setup... -
Page 55: Advanced: H/W Monitor
All manuals and user guides at all-guides.com 3.4.7 Advanced: H/W Monitor Chapter 3 – AMI BIOS Setup... -
Page 56: Setup Submenu: Chipset
All manuals and user guides at all-guides.com Setup submenu: Chipset Options summary: (default setting) Host Bridge Host Bridge Parameters South Bridge South Bridge Parameters Chapter 3 – AMI BIOS Setup... -
Page 57: Chipset: Host Bridge
All manuals and user guides at all-guides.com 3.5.1 Chipset: Host Bridge Options summary: (default setting) Intel IGD Configuration Enter to set Graphic Configuration Memory Information Show current memory information Chapter 3 – AMI BIOS Setup... -
Page 58: Chipset: Igd Configuration
All manuals and user guides at all-guides.com 3.5.1.1 Chipset: IGD Configuration Options summary: (default setting) Auto Disable IGD Disabled Enabled Support Auto Disable IGD IGFX – Boot Type VBIOS Default Select the Video Device which will be activated during POST Fixed Graphics Memory 128MB Size... -
Page 59: Chipset: South Bridge
All manuals and user guides at all-guides.com 3.5.2 Chipset: South Bridge Options summary: (default setting) Power Mode Select AT/ATX Power Mode TPT Devices Configure onboard TPT Devices PCI Express Port x Disabled Enabled Enable/Disable PCI Express Port 0 - 3 Chapter 3 –... -
Page 60: South Bridge: Tpt Devices
All manuals and user guides at all-guides.com 3.5.2.1 South Bridge: TPT Devices Options summary: (default setting) Azalia Controller Disabled HD Audio Azalia Controller Enable/Disable R8111E #x Controller Disabled Enabld R8111E Enable/Disable Chapter 3 – AMI BIOS Setup... -
Page 61: Setup Submenu: Boot
All manuals and user guides at all-guides.com Setup submenu: Boot Options summary: (default setting) Quiet Boot Disabled Enabled Enables or disables Quiet Boot option Launch 8111E PXE OpROM Disabled Enabled En/Disable PXE boot for onboard 8111E LAN Boot Option #X XXXX Drive BBS Priorities The order of boot priorities. -
Page 62: Boot: Bbs Priorities
All manuals and user guides at all-guides.com 3.6.1 Boot: BBS Priorities Options summary: (default setting) Boot Option #x Disabled Device name Sets the system boot order Chapter 3 – AMI BIOS Setup... -
Page 63: Security
All manuals and user guides at all-guides.com Security Options summary: (default setting) Administrator Password/ Not set User Password Change User/Administrator Password You can set a User Password once an Administrator Password is set. The password will be required during boot up, or when the user enters the Setup utility. Please Note that a User Password does not provide access to many of the features in the Setup utility. - Page 64 All manuals and user guides at all-guides.com confirmation. Press Enter again after you have retyped it correctly. Removing the Password Highlight this item and type in the current password. At the next dialog box press Enter to disable password protection. Chapter 3 –...
-
Page 65: Security: Hdd Security
All manuals and user guides at all-guides.com 3.7.1 Security: HDD Security Options summary: (default setting) Set User Password/ Not set Set Master Password Before booting to OS, HDD will be set to a frozen state. On S3 resume HDD will be unlocked using the HDD Password we entered while system booting. - Page 66 All manuals and user guides at all-guides.com Removing the Password Highlight this item and type in the current password. At the next dialog box press Enter to disable password protection. Chapter 3 – AMI BIOS Setup...
-
Page 67: Setup Submenu: Save & Exit
All manuals and user guides at all-guides.com Setup submenu: Save & Exit Options summary: (default setting) Save Changes and Reset Reset the system after saving the changes Discard Changes and Reset Reset system setup without saving any changes Restore Defaults Restore/Load Default values for all the setup options. -
Page 68: Chapter 4 - Drivers Installation
All manuals and user guides at all-guides.com Chapter 4 Chapter 4 – Drivers Installation... -
Page 69: Product Cd/Dvd
All manuals and user guides at all-guides.com Product CD/DVD The AEC-6613 comes with a product DVD that contains all the drivers and utilities you need to setup your product. Insert the DVD and follow the steps in the autorun program to install the drivers. In case the program does not start, follow the sequence below to install the drivers. - Page 70 All manuals and user guides at all-guides.com Open the STEP4 - Audio folder and select your OS Open the Setup.exe file in the folder Follow the instructions Drivers will be installed automatically Step 5 – Install RAID & AHCI Driver Please refer to Appendix C Step 6 –...
-
Page 71: Appendix A - Watchdog Timer Programming
All manuals and user guides at all-guides.com Appendix A Appendix A - Watchdog Timer Programming... -
Page 72: Watchdog Timer Programming
All manuals and user guides at all-guides.com A.1 Watchdog Timer Programming AEC-6613 utilizes the ITE 8783 chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON initial watchdog timer program is also attached based on which you can develop customized program to fit your application. - Page 73 All manuals and user guides at all-guides.com the key-check logic, it is necessary to perform four write operations to the Special Address port (2EH). Two different enter keys are provided to select configuration ports (2Eh/2Fh) of the next step. (2) Modify the Data of the Registers All configuration registers can be accessed after entering the MB PnP Mode.
- Page 74 All manuals and user guides at all-guides.com Watch Dog Timer 1, 2, 3 Control Register (Index=71h,81h,91h Default=00h) Watch Dog Timer 1, 2, 3 Configuration Register (Index=72h, 82h, 92h Default=001s0000b) Watch Dog Timer 1,2,3 Time-Out Value (LSB) Register (Index=73h,83h,93h, Default=38h) Appendix A – Watchdog Timer Programming...
- Page 75 All manuals and user guides at all-guides.com Watch Dog Timer 1,2,3 Time-Out Value (MSB) Register (Index=74h,84h,94h Default=00h) Appendix A – Watchdog Timer Programming...
-
Page 76: Ite8783 Watchdog Timer Initial Program
All manuals and user guides at all-guides.com A.2 ITE8783 Watchdog Timer Initial Program .MODEL SMALL .CODE Main: CALL Enter_Configuration_mode CALL Check_Chip mov cl, 7 call Set_Logic_Device ;time setting mov cl, 10 ; 10 Sec dec al Watch_Dog_Setting: ;Timer setting mov al, cl mov cl, 73h call Superio_Set_Reg ;Clear by keyboard or mouse interrupt... - Page 77 All manuals and user guides at all-guides.com Initial_OK: CALL Exit_Configuration_mode MOV AH,4Ch INT 21h Enter_Configuration_Mode PROC NEAR MOV SI,WORD PTR CS:[Offset Cfg_Port] MOV DX,02Eh MOV CX,04h Init_1: MOV AL,BYTE PTR CS:[SI] OUT DX,AL INC SI LOOP Init_1 Enter_Configuration_Mode ENDP Exit_Configuration_Mode PROC NEAR MOV AX,0202h CALL Write_Configuration_Data Exit_Configuration_Mode ENDP...
- Page 78 All manuals and user guides at all-guides.com CALL Read_Configuration_Data CMP AL,87h JNE Not_Initial MOV AL,21h CALL Read_Configuration_Data CMP AL,81h JNE Not_Initial Need_Initial: Not_Initial: Check_Chip ENDP Read_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL MOV DX,WORD PTR CS:[Cfg_Port+06h] IN AL,DX Read_Configuration_Data ENDP Write_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h]...
- Page 79 All manuals and user guides at all-guides.com MOV DX,WORD PTR CS:[Cfg_Port+06h] OUT DX,AL Write_Configuration_Data ENDP Superio_Set_Reg proc near push ax MOV DX,WORD PTR CS:[Cfg_Port+04h] mov al,cl out dx,al pop ax inc dx out dx,al Superio_Set_Reg endp.Set_Logic_Device proc near Set_Logic_Device proc near push ax push cx...
- Page 80 All manuals and user guides at all-guides.com DW 02Eh,02Fh END Main Note: Interrupt level mapping 0Fh-Dh: not valid 0Ch: IRQ12 03h: IRQ3 02h: not valid 01h: IRQ1 00h: no interrupt selected Appendix A – Watchdog Timer Programming...
-
Page 81: Appendix B - I/O Information
All manuals and user guides at all-guides.com Appendix B Appendix B - I/O Information... -
Page 82: I/O Address Map
All manuals and user guides at all-guides.com I/O Address Map Appendix B – I/O Information... - Page 83 All manuals and user guides at all-guides.com Appendix B – I/O Information...
-
Page 84: St Memory Address Map
All manuals and user guides at all-guides.com Memory Address Map Appendix B – I/O Information... -
Page 85: Irq Mapping Chart
All manuals and user guides at all-guides.com IRQ Mapping Chart Appendix B – I/O Information... - Page 86 All manuals and user guides at all-guides.com Appendix B – I/O Information...
-
Page 87: Dma Channel Assignments
All manuals and user guides at all-guides.com DMA Channel Assignments Appendix B – I/O Information... -
Page 88: Appendix C -Ahci Settings
All manuals and user guides at all-guides.com Appendix C Appendix C –AHCI Settings... -
Page 89: Setting Ahci
All manuals and user guides at all-guides.com C.1 Setting AHCI OS installation to setup AHCI mode Step 1: Copy the files below from “Driver CD -> STEP5-AHCI\WIN7_32\F6 Install Floppy Create for 32 and 64 bit Windows” to Disk Step 2: Setup OS Appendix C –... - Page 90 All manuals and user guides at all-guides.com Step 3: Press “F6” Step 4: Choose “S” Appendix C – AHCI Settings...
- Page 91 All manuals and user guides at all-guides.com Step 5: Choose “Intel® NM10 Express Chipset” Step 6: It will show the model number you select and then press “ENTER Step 7: Setup is loading files Appendix C – AHCI Settings...