Table of Contents
Advertisement
Available languages
Available languages
SAVE THESE
INSTRUCTIONS
Additional Safety Information
WARNING:
or any part of it. Damage or personal injury could result.
WARNING:
Everyday eyeglasses are NOT safety glasses. Also use face
or dust mask if cutting operation is dusty. ALWAYS WEAR
CERTIFIED SAFETY EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NIOSH/OSHA/MSHA respiratory protection.
WARNING:
product contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• compounds in fertilizers
• compounds in insecticides, herbicides and pesticides
• arsenic and chromium from chemically treated lumber
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
• Avoid prolonged contact with dust from power
sanding, sawing, grinding, drilling, and other
construction activities. Wear protective clothing and
wash exposed areas with soap and water. Allowing dust
to get into your mouth, eyes, or lay on the skin may promote
absorption of harmful chemicals.
WARNING:
generate and/or disperse dust, which may cause serious and
permanent respiratory or other injury. Always use NIOSH/
OSHA approved respiratory protection appropriate for the
dust exposure. Direct particles away from face and body.
WARNING:
personal hearing protection that conforms to ANSI
S12.6 (S3.19) during use. Under some conditions and
duration of use, noise from this product may contribute to
hearing loss.
CAUTION:
on its side on a stable surface where it will not cause a
tripping or falling hazard. Some tools will stand upright
but may be easily knocked over.
Air vents often cover moving parts and should be
avoided. Loose clothes, jewelry or long hair can be caught in
moving parts.
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ......................... volts
Hz ....................... hertz
min ..................... minutes
or DC ...... direct current
Never modify the power tool
ALWAYS use safety glasses.
Some dust created by this
Use of this tool can
Always wear proper
When not in use, place tool
...................... Class I Construction
(grounded)
.../min .............. per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM .................... strokes per minute
A ......................... amperes
W ........................ watts
or AC ........... alternating current
or AC/DC .... alternating or
direct current
...................... Class II
Construction
(double insulated)
n o ....................... no load speed
ASSEMBLY AND ADJUSTMENTS
WARNING:
serious personal injury, turn unit off and remove
the battery pack before making any adjustments or
removing/installing attachments or accessories. An
accidental start-up can cause injury.
CAUTION:
before removing extension attachment or end attachment.
An attachment must be attached to the housing before use.
Blow Tube Assembly (Fig. B)
1. To attach the tube to the blower, line up the pegs
the bottom of the tube with the notch
the housing opening as shown in Fig. B.
2. Push the tube into the blower housing until the lock
engages the tube.
3. Pull on the tube to ensure it is securely in place.
4. To remove the tube, insert a screwdriver into the
unlocking hole
9
on the side of the blower tube. Depress
the tab inside and pull tube off.
WARNING:
without tube securely in place. Never reach down into
housing through tube hole.
WARNING:
when you leave blower unattended or when storing, checking,
adjusting, cleaning, or working on blower.
Installing and Removing the Battery Pack (Fig. C, E)
nOTE: For best results, make sure your battery pack is
fully charged.
WARNING:
battery, make certain the speed lock lever
position to prevent switch actuation (Fig. E).
To install battery pack: Insert battery pack
housing
as shown in Fig. C until fully seated and an
6
audible click is heard. Make sure battery pack is fully seated
and fully latched into position.
To remove battery pack: Depress the battery release
button
11
in the top of the battery housing and pull
battery pack out of appliance.
English
n ......................... rated speed
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation
..................... wear respiratory
protection
..................... wear eye
protection
..................... wear hearing
protection
..................... read all
documentation
To reduce the risk of
Ensure the battery is removed
7
8
on the bottom of
Do not operate blower
Always remove the battery
Before removing or installing
2
is in the off
10
into battery
on
5
Advertisement
Table of Contents
