Table of Contents
Advertisement
K3G355-PJ75-05
Product conforming
EN 61800-5-1; CE
to standard
Approval
EAC; CCC; UL 1004-7 + 60730-1;
CSA C22.2 no. 77 + CAN/CSA-
E60730-1
For cyclic speed loads, note that the rotating parts of the device
are designed for maximum one million load cycles. If you have
specific questions, contact ebm-papst for support.
; Use the device in accordance with its protection type.
Notes on surface quality
The surfaces of the products conform to the generally applicable industrial
standard. The surface quality may vary during the production period.
Strength, dimensional stability and dimensional accuracy are not affected
by this.
The colour pigments of the paints used react perceptibly to UV light over
the course of time. This does not however have any influence on the
technical properties of the products. To prevent the formation of patches
and fading, the product is to be protected against UV radiation. Changes
in colour are not a reason for complaint and are not covered by the
warranty.
3.5 Mounting data
; Secure the mounting screws against accidentally coming loose (e.g.
by using self-locking screws).
Strength class for
8.8
mounting screws
Any further mounting data required can be taken from the product
drawing or Section chapter 4.1 Connecting the mechanical system.
3.6 Transport and storage conditions
Max. permissible
+80 °C
ambient motor temp.
(transp./ storage)
Min. permissible
-40 °C
ambient motor temp.
(transp./storage)
3.7 Electromagnetic compatibility
EMC interference
Acc. to EN 61000-6-2 (industrial
immunity
environment)
EMC interference
Acc. to EN 61000-6-3 (household
emission
environment), except EN 61000-3-2 for
professionally used devices with a total
rated power greater than 1 kW
If several devices are connected in parallel on the mains side,
so that the line current of the arrangement is in the 16-75 A
range, this arrangement conforms to IEC 61000-3-12, provided
that the short-circuit power S
customer system to the public power grid is greater than or
equal to 250 times the rated output of the arrangement. It is the
responsibility of the installation engineer or operator/owner of the
device to ensure, if necessary after consultation with the
network operator, that this device is only connected to a
connection point with a S
250 times the rated output of the arrangement.
Item no. 54828-5-9970 · ENG · Revision 202174 · Release 2018-12-20 · Page 6 / 13
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
Operating instructions
at the connection point of the
sc
value that is greater than or equal to
sc
4. CONNECTION AND START-UP
4.1 Connecting the mechanical system
CAUTION
Cutting and crushing hazard when removing device
from packaging
→ Carefully remove the device from its packaging, only
touching the housing. Strictly avoid shocks.
→ Wear safety shoes and cut-resistant safety gloves.
CAUTION
Heavy load when taking out the device
Bodily harm, e.g. back injuries, are possible.
→ Two people should remove the device out of its packaging
together.
NOTE
Damage to device from vibration
Bearing damage, reduced service life
→ Forces or impermissibly high vibration levels must not be
transmitted to the fan from system components.
→ If the fan is connected to air ducts, it should isolated from
vibrations, for example using compensators or similar
elements.
→ Fasten the fan to the substructure without distorting it.
; The fan may not be handled in the area around the inlet nozzle during
transport and installation.
There is a risk of damage to the impeller.
; Check the device for transport damage. Damaged devices must no
longer be installed.
; Install the undamaged device according to your application.
CAUTION
Possibility of damage to the device
Serious damage may result if the device slips during assembly.
→ Keep the device fixed in position at the installation location
until all attachment screws have been tightened.
The fan must not be strained on fastening.
●
4.2 Connecting the electrical system
DANGER
Electric voltage on the device
Electric shock
→ Always install a protective earth first.
→ Check the protective earth.
DANGER
Incorrect insulation
Risk of fatal injury from electric shock
→ Use only cables that meet the specified installation
requirements for voltage, current, insulation material, load etc.
→ Route cables such that they cannot be touched by any
rotating parts.
Advertisement
Table of Contents
