DeWalt DCK264P2T-GB Original Instructions Manual page 37

Selecting the Mode (Fig. E)
DCN660 only
To select sequential action mode, slide the mode selector
switch 10 to the single nail icon (
To select bump action mode, slide the mode selector switch
to the three nail icon ( ).
Trigger Lock-off (Fig. F)
This tool is equipped with a trigger lock-off
the tool from firing a nail.
To engage the trigger lock-off, push the switch downward.
To release the trigger lock-off

WARNING: Make sure the trigger lock-off
and the battery pack is removed before making any
adjustments or when tool is not in immediate use.
Non-mar Tip (Fig. A)
Place the no-mark tip 14 over the contact trip
is used on wood.
Store the no-mark tip at the holder
be used.

WARNING: Make sure the trigger lock-off
and the battery pack is removed before installing or
removing the no-mark tip.
Worklights (Fig. H)
This tool has worklights 5 located on each side. The worklights
will light upon activating the trigger or releasing the contact
trip. The lights will automatically go off after 10 seconds of
non-operation. The worklights also function as a low battery
indicator and a jammed nail indicator. For further details, refer to
Low Battery Indicator or Clearing Stall or Jammed Nail.

WARNING: The worklights are intended for lighting the
immediate work surface. Do not use the worklights as the
only light source.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Proper Hand Position (Fig. I)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main handle.
).
13 which prevents
13 , pull the switch upward.
13 is engaged
2 when the tool
7 whenever it is not to
13 is engaged
Preparing the Tool (Fig. A)
1. Remove battery pack and all nails from the magazine.
2. Check if the contact trip
3. Reload the nails to the magazine.

WARNING: Do not use the tool if the contact trip or nail
10
pusher cannot move freely.

CAUTION: NEVER spray or in any other way apply
lubricants or cleaning solvents inside the tool. This can
seriously affect the life and performance of the tool.
Actuating the Tool (Fig. A)
The DCN660 can be operated using one of two modes:
sequential action mode or bump action mode.
The DCN661 operates in sequential mode only.
Sequential Action Mode
The sequential action mode is used for intermittent nailing
when very careful and accurate placement is desired.
1. Use the mode selector switch
action mode. (DCN660 only)
2. Release the trigger lock-off
3. Push the contact trip
4. Pull the trigger switch
5. Release trigger and remove contact trip from work piece.
6. Repeat steps 3 – 5 to fire subsequent nails.
Bump Action
DCN660 only
The bump action mode is used for rapid nailing on flat,
stationary surfaces.
1. Use the mode selector switch
action mode.
2. Release the trigger lock-off
3. To drive a single nail, operate the tool as described for
sequential action:
a. Push the contact trip
b. Pull the trigger switch
4. To drive several nails, depress and hold the trigger
switch , and then push the contact trip
1
against the work surface. Each time the contact trip
depressed whilst the trigger

WARNING: Do not keep the trigger depressed when the
tool is not in use. Keep the trigger lock-off
position to prevent accidental actuation when the tool is
not in use.
Clearing a Stall or Jammed Nail
(Fig. A, G, H)
If a nail becomes jammed in the nosepiece or the tool stalls, the
right-hand worklight
5
1. Engage the trigger lock-off
2 and nail pusher can move freely.
10 , select the sequential
.
13
2 against the work surface.
1 to actuate the tool.
10 to select the bump
13 .
2 against the work surface.
1 to actuate the tool.
repeatedly
2
1 is held, a nail will fire.
13 in the locked
will blink continuously.
.
13
ENGLIsh
2 is
35