Erfal EASE, M25S - Wireless-Drive EASE Installation Guide

Notes / Charging

• Please charge the battery full before the first use or when the Status-LED on the motor head indicates low battery, to do this, remove the battery from the motor head.
• The charging time approx. 3-4 hours. The LED on the charger ease lights up red during charging and green when fully charged.
• Use the original charger ease for charging. Pull the motor plug and insert the charging plug in the same position.
• When the motor plug is inserted, the motor is in sleep mode. The motor plug must be removed permanently to enable all functions.
• The programming of the channels as well as the end positions are permanently stored and remain even when the battery is completely discharged.
  

Install the Access Point

1. Connect your access point to your router using the provided network cable and power it up.
   
2. Install the Homematic IP App from Apple App Store or Google Play.
   
   
   
   
   
   
   
   
3. Start the App and follow the on-screen instructions to finish setting up the Access Point.

Join a shade

Make sure the shading product is properly mounted and fully charged! The LED on the charger Ease lights up green when the drive is fully charged.

1. With each product you have a QR code sticker. Make sure you have it available.
   Keep the sticker in a safe location.
   Never throw it away!
   Example QR code sticker, fixed on the back side of the Motor flag:
   
   
2. Remove the Motor plug.
3. After approximately 30 seconds the Motor-LED will start blinking orange.
4. Press bottom right More button.
   
5. Select Teach-in device.
   The App will now start looking for new devices.
   Verify the Motor-LED is blinking ORANGE every 10 seconds. If the motor has gone to sleep (after 3 minutes of inactivity after powering up the device), wake it up by pressing the motor button. The motor might start to move. Press the button once more to stop movement.
6. Follow the instructions in the App to finish the installation.
7. You have now arrived at the home screen of the App.

Reset

Note: The transport fuse or the charging cable must be removed in advance!

Press the configuration button for about 4 seconds until the status LED flashes yellow several times.

Then release the configuration button immediately and press again for about 4 seconds.
The status LED flashes green briefly.
The engine has been successfully reset and can be retrained.
If it was not successful, the status LED flashes briefly red after the multiple yellow flashing. The process must be repeated.

LOGISTICS / APPLICATIONS

Articel number
17.0802.0000 / 6574804

Application
Roller Blinds Ø 31 / 37 mm

Product range
Jalousie Basic Line, Plissee ESM1

Size limitations (mm)

The motor may be only installed by qualified personnel who:

• have read and understood the mounting instructions of both blind, product and the motor and are familiar with the electronic safety aspects,
• recognize and avoid danger which can be produced from the mechanical or electrical components,
• always observe and are familiar with the local safety, labour regulations and laws in order to avoid personal injury and property damage due to improper installation, these must be carried out by a specialist company in accordance with current standards and guidelines.
  

Accessories

Description / Product code / Article number
Charger Ease / 17.0808.0000 / 6574828
Homematic IP Access Point /17.0810.0000 / 6574835

Warning and user notes

• Use only in dry places indoors - risk of electric shock and fire.
• Charge only suitable Ease HmIP Li-Ion rechargeable batteries.
• Other chemistries and types of batteries might bust causing injury to persons and damage.
• Do your part for environmentally friendly recycling.
• Dispose of the electric motor separately from the rest of the system and only in designated collection points.
  
• Detailed information "Removal of the electric motor" (Remove the plastic end caps, disconnect the cable connection between the motor and the battery pack, pull the side motor and the battery pack out of the rail from the side) can be found in the following Website https://www.erfal/en/enterprise/service/downloadportal or the QR-Code.