Advertisement
HD-Force
Function | Operation |
Power ON | Press and hold the POWER button for 2 seconds |
Power OFF | Press and hold the POWER button for 3 seconds |
Play /Pause | Press the PLAY / PAUSE button |
Volume + | Press the VOLUME + button |
Volume - | Press the VOLUME - button |
Next track | Press and hold the VOLUME + button for 2 seconds |
Previous track | Press and hold the VOLUME - button for 2 seconds |
Switch between Wireless / AUX/SD card modes | Press the POWER button |
Switch the multicolor LED light mode/Turn OFF LEDs | Double-press the PLAY / PAUSE button |
Answer a phone call | Press the PLAY / PAUSE button during incoming call |
Reject a phone call | Press and hold the PLAY / PAUSE button for 2 seconds during incoming call |
End a phone call | Press the PLAY / PAUSE button when on call |
TWS mode | Take two HD-Force, double-press the POWER button on both speakers while two of them are turned ON and not connected |
Disconnect | Press and hold the VOLUME + and the VOLUME - buttons simultaneously for 3 seconds when connected to a device |
Factory reset | Press and hold the VOLUME + and the VOLUME - buttons simultaneously for 3 seconds when disconnected from a device |
Hard reset | Press the HARD RESET button under the rubber cover |
Mute sound (in the AUX mode only) | While connected via AUX cable, press the PLAY / PAUSE button |
Press and hold the POWER button for 2 seconds, You will hear the sound cue, the battery level indicators will light up, the multicolor LED light will start breathing white and the BLUE state indicator will start flashing.
Press and hold the POWER button for 3 seconds. You will hear the sound cue and all the lights will go OFF.
Make sure TREBLAB HD-Force is fully charged.
After the initial pairing, the speaker will automatically connect to the previously paired device when turned ON again. If reconnection does not happen automatically, the speaker will start looking for any other previously paired device within the effective distance range. TREBLAB HD-Force can remember up to 6 recently paired devices.
NOTE: The speaker remembers the last mode it was in before it has been turned OFF. So, if the speaker is turned OFF in the SD card mode (considering that the MicroSD card is still in the speaker), after being turned back ON, it will automatically go back to the SD card mode.
The TWS technology allows you to use two speakers paired wirelessly to create a wireless dual-channel system, delivering a true stereo sound effect. While using this function, one speaker (Master, left channel) is paired with a source device, the other (Slave, right channel) speaker is paired with the Master speaker.
There are a few ways to disable the TWS function:
NOTE:
To pause and resume playback when connected wirelessly, press the PLAY / PAUSE button.
To adjust the volume, press the VOLUME + or the VOLUME - button while listening to music.
To change the track on the HD-Force, press and hold the VOLUME + or the VOLUME - button for 2 seconds.
You can connect TREBLAB HD-Force to compatible devices using the supplied 3.5mm AUX cable.
To mute the audio, press the PLAY / PAUSE button.
NOTE: On-device control is not supported for the NEXT, PREVIOUS and PAUSE functions when using the 35mm AUX cable. Phone calls management using the PLAY / PAUSE button is not supported as well. You will need to make adjustments using your smart device.
The TREBLAB HD-Force speaker can play music from the MicroSD cards up to 5126B. All you need to do is to copy music to the memory card (in folders or just to the card root), insert it into the MicroSD card slot on the bacl< of the speaker (under the rubber cover). You will hear the sound prompt and the state indicator will turn green.
To start playing from the MicroSD card, press the PLAY / PAUSE button.
The playlist is arranged according to song addition date (the older tracks play first).
The HD-Force speaker supports the following formats: MP2, MP3, WMA, APE, FLAC, AAC, MP4, M4A, WAV, AIF, AFC; and the following file systems: FAT16, FAT32, exFAT, FAT64.
NOTE: When inserting the MicroSD card into the speaker, the card's contact pad should be faced upwards.
TREBLAB HD-Force can be used to make and receive phone calls when connected wirelessly. Audio playback will be paused during calls.
To answer / end a call | Press the PLAY / PAUSE button |
To reject a call | Press and hold the PLAY / PAUSE button for 2 seconds |
To redial | Press and hold the PLAY / PAUSE button for 2 seconds |
NOTE: For better call quality, face the microphone when you speak.
When the battery is running low, you will hear a sound signal.
TREBLAB HD-Force may be used while charging in the Wireless, AUX and SD card modes.
To charge the speaker, plug one end of the supplied cable into the TYPE-C charging port under the rubber cover on the back of the speaker. Plug the other end of the charging cable into a standard USB port. It takes up to 4-5 hours to fully charge.
Once plugged in, the battery level indicators will start flashing slowly showing the current battery level (for more detai s, please check the BATTERY LEVEL INDICATION section). This means that the speaker is charging. When the speaker is fully charged, all tree battery level indicators will stop flashing and become steady.
Be sure to use a 5V DC, 0.5-2A adaptor or charger. Using the power source with lower power will increase the overall charging time.
Unplug HD-Force from the charging cable and the cable itself from the power source when not in use.
If the speaker is left unused, even the fully charged battery will lose its charge over time. We recommend fully charging the HD-Force speaker at least twice a month to maintain sufficient battery life.
The HD-Force speaker is equipped with the battery level indicators - LEDs. The current charge level is displayed when the speaker is ON and when the speaker is used as a power bank in OFF state.
TREBLAB HD-Force inbuilt battery can be used as a power bank to charge your smartphone or tablet.
Problem | Solution |
Not powering on | Make sure the speaker is fully charged. Charge for 2 hours, if necessary. Press and hold the POWER button for 2 seconds. Press the HARD RESET button on the back of the speaker (under the rubber cover). |
Not charging | Clean the charging port using a soft brush. Try charging the case with another Type-C cable, power source, adaptor (if available). Press the HARD RESET button on the back of the speaker (under the rubber cover). |
Not pairing | Make sure the speaker is in the Wireless mode. Make sure the speaker is not paired with any other device, as it can only pair with one device at a time. Press the VOLUME + and VOLUME - buttons simultaneously and hold for 3 seconds. This will force the speaker to forget previously paired devices. Repeat the steps for pairing as previously described. |
MicroSD card is not recognized | The maximum supported MicroSD size of 512GB is exceeded. File formats unsupported. File system of the memory card is not supported. |
Not finding a wireless driver on your laptop | Make sure your laptop supports wireless connections, If it doesn't, you will need an external wireless USB adapter compatible with your laptop. For further details, consult with your laptop manufacturer. |
Frequent disconnection and noise | Ensure that nothing is blocking the signal between your device and the HD-Force. Check if the speaker is running out of power. |
Battery: | Input 5V/0.5A-2A Output 5V/2.1A |
Charging time: | 4-5 hours |
Bluetooth version: | 5.0 |
Supported profiles: | A2DP/AVRCP/HFP/HSP[OPP/HlD/SPP/PBAP/GATT/SM |
Speaker size: | 2 x 50mm, 1 x 80mm |
Output power: | 50W |
Water resistance: | IPX6 |
Charging port: | TYPE-C |
Audio port: | 3.5 mm jack |
MicroSD card file systems: | FAT16, FAT32, exFAT, FAT64 |
MicroSD card supported | MP2/MP3/WMA/APE/FLAC/AAC/MP4/M4A/WAV/AlF/ |
formats: | AIFC |
Dimensions: | 4.58 x 4.58 x 8.74 inches/ 116.5 x 116.5 x 222 mm |
Weight: | 3.2 lbs / 1455g |
The speakers can be recycled, and they should be in order to keep our planet clean, Where should you bring them?
In the US, there are a couple of options:
In Canada, please visit the links below:
https://thinkreuse.net
https://www.call2recycle.ca
In the UK, please visit the links below:
https://www.recycle-more.co.uk/
https://www.recyclenow.com/local-recycling
THANK YOU
We truly appreciate that you chose TREBLAB as your trusted brand of wireless speakers and sincerely hope you enjoy the great sound and seamless usability TREBLAB HD-Force provides. We love making our customers happy by providing true value with our products. If for any reason you are not completely satisfied with your purchase or have any questions, please visit https://treblab.com/contact_us. We care about our customers most of all and are always here to help you.
Parts and Labor Warranty Please visit www.treblab.com to register YOUR product.
Manufactured by Productech
HD-Force
PORTABLE WARELESS SPEAKER
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download TREBLAB HD-Force - Portable Wireless Bluetooth Speaker Manual
Advertisement
Need help?
Do you have a question about the HD-Force and is the answer not in the manual?
Questions and answers