Advertisement
ASSEMBLY DIAGRAMS
1.
3.
5.
7.
30-060403 1LIM.indd 4-5
2.
4.
6.
TELESCOPE ASSEMBLY INSTRUCTIONS
1. Your telescope has adjustable (telescoping) legs (Fig. 1).
2. Stand tripod and spread legs. Loosen the three leg clamps. Grab tripod head and lift. Extend the
tripod legs to the desired height (at equal lengths) and tighten the clamps on each leg to hold
it in position (Fig. 1).
3. Attach the accessory tray (P) to the center leg braces on the tripod legs (Fig 2) and insert accessory
tray and bolt through center of tray into braces and tighten bolt.
4. Remove telescope main body from the box. Attach telescope main body (H) by aligning the hole in
the telescope saddle with that in the yoke. Screw yoke locking knobs (L) through both holes and
tighten the knob.
5. Remove the finderscope (G) with finderscope bracket (F) attached from the box. Remove the
two knurled thumbscrews from the telescope main body. Position the finderscope bracket on the
telescope main body so that the holes in the base of the bracket line up with the exposed holes in
the telescope main body. Replace the two-knurled thumbscrews and tighten securely (Fig. 3).
6. Insert diagonal (D) into the focus tube (C). Secure by tightening small retaining screw on the focus
tube (Fig. 4).
NOTE: Diagonal is only to be use in combination with the eyepieces (oculars). Never use the
diagonal and Barlow at the same time.
7. Insert eyepiece (E) into diagonal (D). Secure by tightening small retaining screw (Fig.5).
NOTE: In all astronomical telescopes, the image appears upside down. With the use of the
diagonal the image appears erect but with a left to right inversion (mirror like). To use the
telescope for terrestrial view and to correct the mirrored image, remove the diagonal
and
replace
with
the
erecting
eyepiece.
magnification
eyepiece
when
the
refractor telescopes come with erector eyepieces. Reflectors (mirrors) are used mainly for
astronomical purposes.
The telescope is now fully assembled and ready for use.
8. To use the Barlow, insert Barlow (Fig. 7) into the focus tube. Secure by tightening small retaining
screw. Insert eyepiece into open end of Barlow and secure.
CAUTION! Viewing the sun can cause permanent eye damage.
Do not view the sun with this telescope or even with the naked eye.
TO USE THE FINDERSCOPE
The finderscope is a small low-powered and wide field of view telescope mounted alongside the main
telescope and is used to search for the target and aim the main telescope at it. But before you can
use the finderscope, you will need to line it up with the telescope. This procedure will become easier
with practice.
1. Install the lowest power eyepiece (25mm) into the eyepiece tube. Pick out an easily recognized,
unmoving object no closer than a thousand yards away. Aim your telescope toward your object
until its image is centered in the eyepiece. Lock all the knobs on the mount so the telescope will not
move.
2. Look through the finderscope. If the object you lined up in the telescope is not visible, loosen the
adjustment screws and move the finderscope around until you see it. Once it gets within range,
tighten the adjustment screws while centering the object in the scope. You will note that the image
will shift toward the screw you are tightening (Fig. 6).
3. Adjust screws to center object on the finderscope cross hairs. Recheck your telescope to make
certain it is still on target. If it moved, realign it and adjust your finderscope. If it hasn't, you're all
set. Your finderscope is now operational.
We
recommend
the
use
of
telescope
is
used
for
terrestrial
viewing.
4/12/05 10:57:40 AM
the
low
Only
Hide quick links:
Advertisement
