Vava VA-AH015 - Ultrasonic Humidifier Manual

Product Diagram

1. Rotatable Nozzles
2. Water Tank
3. Power Cord
4. Humidity Sensor
5. Base
6. LED Display
7. Power Button
8. Sleep Button
9. Mist Button
10. Humidity Button
11. Timer Button
12. Air Inlet
13. Drain Side

Specifications

How to Use

Adding Water

1. Tank Cap
2. Tank Inlet

Rotate the tank cap counterclockwise to loosen it, add an appropriate amount of water into the tank, and screw the cap clockwise to fasten it until no water leaks. Do not rotate with excessive force.

Note:

1. Remove the nozzle before you uplift the water tank, and put it back on when the water tank is placed onto the base after the water has been added.
2. When you fail to open the tank cap, wipe the cap dry and rotate it with proper force.

Operation and Functions

Add water into the tank, connect to a power source, the unit is now in standby mode. Note: The buttons on the control panel are the same as those on the remote control.

Power On / Off

1. In standby mode, tap the Power Button once to enter Level 2 Misting by default and a beep sound will be heard. The LED display will show the mist level, environmental RH, and temperature.
2. Tap it again to power off the misting, and a beep sound will be heard. The LED display shows the RH and temperature only.

Mist Adjustment

The mist level can be adjusted from 1 ~ 3 levels with a tap of the Mist Button. A beep sound will be heard with each tap and the LED display will show the corresponding mist level.

Humidity Setting

1. Tap the Humidity Button once to activate continuous misting and the "CO" icon on the Display flashes 3 times. Before the flashing ends, you can set the humidity level from 30% to 95% through the Humidity Button by 5 with each tap. When set, the corresponding humidity value will flash 3 times to confirm the setting and the humidity icon will keep flashing.

Note: The misting works normally if the set humidity on the unit is higher than the RH and stops if the set humidity is lower than the RH.

2. After the humidity is set, tap and hold the Humidity Button for 1.5 seconds to exit the setting, the LED display will flash "CO" 3 times. The humidity icon will disappear.
3. When the humidity is set, the Mist Button remains responsive.

Timer Setting

1. Tap the Timer Button once, the LED display will show "--H" and flash 3 times. Before the flashing ends, set the timer from 1 to 12 hours by tapping the Timer Button. The corresponding timer will show on the LED Display and flash 3 times to conf irm the setting.
2. When the timer is set, tap and hold the Timer Button for 1.5 seconds to exit the setting. The LED display will show "—H"which will disappear after flashing 3 times.
3. A beep sound will be heard each time you tap the Timer Button.

Sleep Mode

1. Tap the Sleep Button once to enter sleep mode. All icons on the LED display (except the sleep icon) will turn off. In sleep mode, the Mist Button, Humidity Button, and Timer Button remain functional, but the beep sound is disabled.
2. In sleep mode, tap the Power Button to turn off the unit. Tap the Sleep Button to exit sleep mode, the sleep mode icon will disappear.

Memory Function

With power connected, the unit will resume the humidity setting selected the last time it has been turned off (the humidity setting icon will not be shown on the LED display). The timer and sleep mode settings will be cleared.

Water Tank Light

The water tank light will turn on / off with the power.

Low Water or Water Tank Removal Protection

1. When water in the tank is depleted or the water tank is removed, the unit will stop working and the water shortage icon will appear on the LED display.
   
2. The unit will resume working once water is added or the tank is placed back on the base.

www.vava.com

NORTH AMERICA
E-mail: support@vava.com
Tel: 1-888-456-8468 (Monday-Friday: 9:00 – 17:00 PST)
Address: 46724 Lakeview Blvd, Fremont, CA 94538

EUROPE
E-mail: support.uk@vava.com(UK) support.de@vava.com(DE) support.fr@vava.com(FR) support.es@vava.com(ES) support.it@vava.com(IT)
EU Importer: ZBT International Trading GmbH, Halstenbeker Weg 98C,
25462 Rellingen, Deutschland

MANUFACTURER
Shenzhen NearbyExpress Technology Development Company Limited
Address: 333 Bulong Road, Jialianda Industrial Park, Building 1,
Bantian, Longgang District, Shenzhen, China, 518129
Learn more about the EU Declaration of Conformity: https://www.vava.com/downloads-VA-AH015-CE-Cert.html