Cleaning, Maintenance And Care; Environmental Protection; Technical Specifications - Metabo SSP 1000 Instructions Manual

en ENGLISH
(Only for SSP 1000)
5. Adjusting the air tool. See section 6.3.
6. The distance between the air tool and work-
piece should not exceed 20 cm.
. 7. Cleaning, Maintenance and
Care
Danger! Disconnect the compressed air con-
nection before carrying out any work.
Danger! Repair and maintenance work other
than the work described in this section should
only be carried out by qualified specialists.
The air tool, and particularly the suction hose and
the spray nozzle, must be cleaned with a suitable
cleaning agent on completion of work. We recom-
mend that you attach a container filled with cleaning
agent to the air tool and flush the cleaning agent
through the tool at low pressure. Spray the cleaning
agent back into a closed container to ensure that it
is collected and to avoid any unnecessary vapour.
The valve pin and pivot point of the trigger of your
spray gun must be oiled after each cleaning. Store
the compressed air device in dry areas only.
If there is an unexpected blockage or the spray
pattern is contaminated, please clean the nozzle.
- A clean air tool guarantees trouble-free handling
during subsequent work.
- After use, clean and look after the air tool with
extreme care.
Danger! Do not use halogen solvents
containing hydrocarbons (1.1.1 Trichlorome-
thyl, ethyl chloride, etc.) because this results in
chemical reactions, some of which can be
dangerous, with some air tool materials.
Caution. Never immerse the air tool
completely in a solvent.
- All moving parts should be oiled from time to time.
- If the nozzle is removed for cleaning, the thread
and the gasket must be coated with a light grease.
Do not use lubricants containing silicone.
- Store your air tools/devices in dry areas only.
- Carry out regular maintenance to ensure the
safety of the air tool.
- Check that all screw fittings are seated securely,
and tighten if necessary.
- Avoid contact with dangerous substances that
have accumulated on the tool. Wear suitable
personal protective equipment and take appro-
priate measures to remove any dangerous
substances before maintenance.
f
8. Accessories
Use only genuine Metabo accessories.
Only use accessories that are designed for this air
tool and that fulfil the requirements and the specifi-
cations listed in these operating instructions.
The spray nozzle and spray hose are subject to
wear and tear. It is therefore always recommended
to have replacements.
12
For a complete range of accessories, see
www.metabo.com or the catalogue.
9. Repairs
Danger! Repairs to air tools must only be
carried out by qualified specialists, using orig-
inal Metabo spare parts!
If you have Metabo air tools that require repairs,
please contact your Metabo service centre. For
addresses see www.metabo.com.
You can download spare parts lists from
www.metabo.com.

10. Environmental Protection

Observe national regulations on environmentally
compatible disposal and on the recycling of disused
air tools, packaging and accessories. You must not
cause risks to people or the environment.

11. Technical Specifications

Explanatory notes on the specifications on Page 3.
Subject to change in line with technological
advances.
V = Air requirement
1
p = Maximum permissible supply pressure
max.
p = Supply pressure
d = Hose diameter (inner)
i
C = Connecting thread
A = Dimensions:
Length x Width x Height
m = Weight
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
Using these values, you can estimate the
emissions from this tool and compare these with the
values emitted by other tools. The actual values
may be higher or lower, depending on the particular
application and the condition of the tool or mounted
tool. In estimating the values, you should also
include work breaks and periods of low use. Based
on the estimated emission values, specify protec-
tive measures for the user - for example, any organ-
isational steps that must be put in place.
Vibration (acceleration value, frequency-weighted
according to EN 28927):
a = Vibration emission level
h
K = Measurement uncertainty (vibration)
h
Sound level (EN ISO 14462):
L = Sound pressure level
pA
L = Acoustic power level
WA
K , K = Measurement uncertainty
pA WA
Wear ear protectors!