Ultra-safe UT-96516 User Instruction Manual

1-800-850-5914
PHOENIX, AZ USA
MODEL:
__________________________
SIZE: ____________________
DATE: ___________________
Same, but 100% Tie-Off.
WARNING
This product is part of a personal fall
arrest system. The user must read and
follow the manufacturer's instructions
for each component of the system.These
instructions must be provided to the user
of this product. The user must read and
understand these instructions before
using this product. Manufacturer's
instructions must be followed for proper
use and maintenance of this product.
Alteration or misuse of this product, or
failure to follow instructions may result
in serious injury or death.
USER INSTRUCTION MANUAL
DESCRIPTION: IN-LINE SHOCK ABSORBING LANYARD 3600 LB GATES
MODEL: UT-96516, UT-96516Y, UT-96516YSR, UTT-96516, UTT-96516Y, UTT-96516YSR,
UTT-96516YCT, UT-96516LY, UT-96516LYSR, UT-96516LYCA, UTT-96516LY, UT-96516LYCA,
UTT-96516LYSR, UTT-96516AA, UTT-96516YAA, UTT-96516YACA, UT-96516YSRD,
UT-96516LYSRDE, UTT-96516YSRD, UT-96516LYSRDE
MEETS OSHA & ANSI Z359.1 | APPROVED FOR LEADING EDGE
WATCH VIDEO 6 ON ULTRASAFEUSA.COM
Anchorage: The anchorage to which this product is
attached must be capable of sustaining a static load
in the direction applied by the personal fall arrest
system of at least 3600 lbs. with certification of a
qualified person or 5000 lbs. without certification. When
more than one personal fall arrest system is attached to
the same structure, the strength requirements stated
above must be multiplied by the number of personal
arrest systems attached to the structure.
Plan your personal fall protection system.
Before installing and using this equipment,
consider all factors affecting your safety during
use of this equipment.
Shock Absorbing Lanyard
Material: Polyester
Warning tags located
in front and back of shock
absorber or located towards
hook, D-ring or eye end.
• Energy absorber resting force 900 lbs.
Plus 42 inch maximum extension.
• Rig lanyard to allow a maximum free fall distance
of not more than six feet or max impact of 1,800 lbs.
• Connectors and anchorage points must be
compatible and able to support 5,000 lbs.
• Do not allow lanyard to contact sharp or abrasive
surfaces, sparks or temperature above 180 degrees.
• Snap hooks with gate openings larger than
one inch (1") must not be connected to D-rings
on harnesses and belts.
• Remove from service if any damage is detected.
Anchorage connector
material: Nylon
Warning tags are
located towards hook,
D-ring or eye end.
• Use energy absorbers or retractable lanyards
when hazard of free fall can occur.
• Connectors and anchorage points must be compatible
and able to support 5,000 lbs. Always work directly
under anchorage to avoid a swing fall injury.
• Anchorage and tie off points must be at a height
that will not allow a lower level to be struck should
a fall occur. Do not allow product to contact sharp
or abrasive surfaces, sparks or temperatures
above 180 degrees.
• Snap hooks with gate openings larger than
one inch (1") must not be connected.
• Remove from service if any damage is detected
NOTE:Seeadditionalinstructionsonbuckleadjustmentforproperfit.Maximumfree-falldistancesixfeetorenergy
absorberarrestingforceof900lbsperANSIormaximumfallarrestforceof1800lbsperOSHA.Avoidlowerlevelcontact.
1
Warning: Manufacturer's instructions supplied with
this product at time of shipment must be followed.
Failure to do so could result in serious injury or death.
Contact manufacturer if instructions are needed.
• Warnings and instructions must be read and
understood before using equipment.
• Equipment must be used by trained personnel
only.
• Users must understand all OSHA regulations, ANSI
standards, and other relevant regulations and
standards pertaining to fall protection equipment.
This product is part of a personal
fall arrest system; a fall arrest
system is required if there is any
risk that a worker may fall from an
elevated
requirement that the fall arrest
system be used any time a working
height of six feet or more is
reached. Working height is defined
as the distance
walking/working surface to a grade
or lower level.
1
2
3
4
5
6
7
1. Back 'D' ring is for fall arrest
2. Shoulder 'D' rings. (if present) are for retrieval use
only use locking snaps.
3. Side 'D' rings (if present) are for positioning only.
4. Front 'D' ring (if present) is for fall arrest
(foot first falls only, 2 foot max free fall), work
positioning, travel restraint or rescue
5. Hip attachment elements are for work positioning
or travel restraint
6. Visual load indicator
7. Park lanyard here
position. It is a
from the
313L2