Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Heritage Bathrooms SDC04
Summary of Contents for Heritage Bathrooms SDC04
- Page 1 Installation Instructions and User Guide Thermostatic Recessed Dual Control Shower Valve Models covered: SDC04, SDA04, SOC10, SGC03, SGA03, SHDC02 & SHDA02 Please keep this booklet for future reference. Installer, when you have read these in- structions please ensure you leave them...
-
Page 2: Table Of Contents
Contents Thank you for choosing Heritage, the UK’s market leader for classic bathroom products. To ensure this product works to its full potential, it needs to be fitted correctly. These fitting instructions have been created to give you all of the information you need. If you need any further help, please do not hesitate to give us a call on 0844 701 8503. -
Page 3: Important Safety Information
Important Safety Information • Please read these instructions thoroughly and retain for future use. • All products manufactured and supplied by Heritage are safe provided they are installed, used correctly and receive regular maintenance in accordance with these instructions. • If you are in any doubt about your ability to install this product safely you must employ the services of an experienced qualified plumber. -
Page 4: General Information
General Information This product has been tested to the Water Regulations Advisory Scheme (WRAS) and satisfies the requirements of the Water Supply (Water Fittings) Regulations 1999 and current bylaws. For full Installation Requirements & Notes (IRN) please visit www.wras.co.uk/directory. BS7600 recommends the temperature of stored water should never exceed 65ºC. A stored water temperature of 60ºC is considered sufficient to meet all normal requirements and will minimise the build up of lime scale in hard water areas. -
Page 5: Product Features
Turn the handle anti-clockwise for a hotter temperature. Note: The SDC04 & SDA04 can either be SOC10 shown installed portrait or landscape. Need help? Give us a call on 0844 701 8503 and speak to one of our trained advisers. -
Page 6: Specifications
Specifications Inlet connections: 15mm compression with 150mm between centres. Minimum working pressure: 0.2 bar Note: This product has been designed to deliver a high flow of water on low pressure systems, however depending on the installation, type of system and shower accessories used, a higher pressure maybe required to optimise the showering experence. -
Page 7: Pack Contents
Pack Contents - SDC04 & SDA04 1. Concealing plate x1 2. Handles x2 3. Shrouds x2 4. Screws x2 5. Valve body x1 6. Valve body fixings x2/2 7. Inserts x2 8. Flow regulators x2 9. Filter washers x2 10. Wall outlet x1 11. - Page 8 Pack Contents - SOC10 1. Concealing plate x2 2. Valve body x1 3. Handles x2 4. Spline adaptors x2 5. Valve body fixings x2/2 6. Inserts x2 7. Flow regulators x2 8. Filter washers x2 9. Wall outlet x1 10. Shrouds x2 Need help? Give us a call on 0844 701 8503 and speak to one of our trained advisers.
-
Page 9: Prior To Installation
Prior to Installation Flow Regulators This shower valve is supplied with a 5 and 7 litre per minute flow regulator loose in the box which must be fitted if the shower valve Filter is installed in conjunction with an instantane- Washer ous water heater / combination boiler. -
Page 10: Installation
Installation - Shower Valve Important: Water supplies to the mixer This shower valve is designed for installations where a recessed valve is already must be with hot on the left and cold on the installed in the wall cavity and is to be re- right when viewed from the front. - Page 11 Installation - Shower Valve 4. Fit concealing plate Note: The concealing plate can be used as a template by drawing around the plate and measuring in by 10mm to give sufficient clearance. Run a bead of waterproof silicon sealant around the inner edge of the concealing plate. Slide the concealing plate onto the shower valve control handles and apply firm pressure to ensure to silicon sealant spreads.
-
Page 12: Wall Outlet
Installation - Wall Outlet Fitting the Wall Outlet There are two methods of fixing the wall outlet Backnut depending on the type of wall: a: With rear access once wall finished Fit the rubber washer to the back of the wall Rubber outlet, place the assembly through a 25-30mm seal... -
Page 13: Operating The Shower
Operating the Shower 1. On / Off control Turn the handle clockwise to turn on and increase the flow of water. Turn the handle anti-clockwise to turn off the flow of water. 2. Temperature control Adjustable temperature control. Turn the handle clockwise for a cooler tem- perature. -
Page 14: Maintenance
Maintenance General Cleaning Your fitting has a high quality finish and should be treated with care to preserve the visible surfaces. All surfaces will wear if not cleaned Unscrew correctly, the only safe way to clean your anti-clockwise product is to wipe with a soft damp cloth. to remove Stains can be removed using washing up liquid. -
Page 15: Adjusting The Temperature
Adjusting the Temperature Adjusting the Temperature temperature of the water with a The shower valve has been factory set to thermometer. If the temperature is not cor- 42ºC with equal (balanced) hot and cold rect, re-calibrate the shower valve: water supply pressures, with the hot water 1. -
Page 16: Troubleshooting
Troubleshooting Symptom Remedy Cause No flow or low Check showerhead, hose and Clean as necessary, refer to flow rate and filters for any blockage. Maintenance section (page 14). / or varying Partially closed stop or service Open stop or service valve. temperatures. - Page 17 Troubleshooting Symptom Cause Remedy Water leaking This is normal for a short time Adjust angle of showerhead in from showerhead. after turning off. holder as necessary to vary draining time. Shower cartridge failing to close Remove shower cartridge and fully, possibly due to water borne check.
-
Page 18: Guarantee
Guarantee When you buy a Heritage product, you can • Repair under this guarantee does not be confident that it not only features a beau- extend the original expiry date. The tiful, distinctive, classic design, but that it has guarantee on any replacement parts or also been made to the very highest quality product ends at the original expiry date. - Page 19 Guarantee • Need help? Expert plumbing engineers If this product does not function correctly If we can’t solve the problem over the ‘phone when first used, contact Heritage or with a spare part, then we’ll send out one Customer Service on 0844 701 8503 of our engineers to take a look.
- Page 20 Birch Coppice Business Park Dordon Tamworth Staffordshire B78 1SG Web: www.heritagebathrooms.com Email: technical@heritagebathrooms.com Tel: 0844 7018503 Part Number: FI: VO Front Access Issue: D3...
Need help?
Do you have a question about the SDC04 and is the answer not in the manual?
Questions and answers