Advertisement
Quick Links
Objective: To troubleshoot elevation issues for Elite, EL0P2, EL0P2.10
Action
1 To troubleshoot elevation issues for the EL0P2, and EL0P2.10
follow steps below.
Section 2,3. `´´Checking elevation Motor´´
(Go to this section if the elevation is not moving at all, or
moving in 1 direction, or moving just a little).
Section 4 ´´6 or 7 Flashing lights´´
(Go to this section if the Charged/Charging LED is giving 6 or 7
flashing lights, then a pause and then 6 flashing lights).
Section 5,6 ´´Removing Red Case´´
(Go to this section if the elevation moves freely and there is no
resistance on the motor itself).
2
If the elevation is still not moving, please move onto the next
step below.
Author: CT
Contributors: JR,RR, JJ
Elite Model, Pickle2 and Pickle 2.10
TS – My Elevation Is Not Working
Checking Elevation Motor
1. Unscrew control panel and pull it out
and to the side. Be careful not to
disconnect any additional wires.
2. Switch the elevation and feed
connections on the green electronic
board on the back of the control panel.
3. Turn on machine and press either
direction of the elevation button. If the
feed wheel does not turn this control
panel is failing, a new control panel
(EL52.P2, EL52.P2.10) is needed.
Elevation & Feed Connections
Orig. date: 9/20/10
Revised:4/11/2022
Pictures
Control Panel – Open
Advertisement
Related Manuals for LOBSTER SPORTS Elite
Summary of Contents for LOBSTER SPORTS Elite
- Page 1 Elite Model, Pickle2 and Pickle 2.10 TS – My Elevation Is Not Working Objective: To troubleshoot elevation issues for Elite, EL0P2, EL0P2.10 Action Pictures 1 To troubleshoot elevation issues for the EL0P2, and EL0P2.10 follow steps below. Section 2,3. `´´Checking elevation Motor´´...
- Page 2 Do this until all 6 wires have been unplugged and the reconnected. 3. For the Elite Pickle 2.10 machines (units with the 10 function remote), you will disconnect the 3 wires connected to the elevation switch itself, and 6 wires from elevation switch (Pickle 2) connected to circuit board.
- Page 3 Elite Model, Pickle2 and Pickle 2.10 TS – My Elevation Is Not Working 1. With the control panel unscrewed, disconnect the Elevation cable from the Elevation Tab on the circuit board. 2. Turn on the machine. If the panel stops giving 6 or 7 flashing lights on the Charged Charging LED then follow the next steps.
- Page 4 Elite Model, Pickle2 and Pickle 2.10 TS – My Elevation Is Not Working Removing the Red Case *(Make sure the machine is turned off). 1. remove the case by unscrewing the (6) screws along the bottom of the red case.
- Page 5 Elite Model, Pickle2 and Pickle 2.10 TS – My Elevation Is Not Working (Elite model Pickle 2 link, shoulder bolt, location) Checking the Link on the Elevation Motor 1. Check to see if you can move the link off away from the...
- Page 6 TS – My Elevation Is Not Working Elite Pickle 2 elevation link 2. For the elite Pickle 2 machines, check to make sure the Should Bolt attaching link arm 1 and link arm 2 is present. If both arms are away from each other, you will need to re- attach them with a shoulder bolt.
- Page 7 TS – My Elevation Is Not Working If the Elevation link is firmly attached to the elevation motor shaft, and the link is not missing the should bolt (for elite Pickle 2 machines) then continue on to the next section.
- Page 8 Elite Model, Pickle2 and Pickle 2.10 TS – My Elevation Is Not Working (Link to Shoulder Bolt location Elite Pickle 2). Putting The Case Back On The Machine 1. Lift the case over the unit, and guide it over until the yoke pointer is facing the ball exit, and the back panel is facing the handle assembly.