Advertisement
Quick Links
Objective: To troubleshoot elevation issues for Elite EL01, EL02, EL03, EL0P2
Action
1 To troubleshoot elevation issues for the EL01, EL02, and
EL03, and EL0P2 follow steps below.
Section 2,3. `´´Checking elevation Motor´´
(Go to this section if the elevation is not moving at all, or
moving in 1 direction, or moving just a little).
Section 4 ´´6 Flashing lights´´
(Go to this section if the Charged/Charging LED is giving 6
flashing lights, then a pause and then 6 flashing lights).
Section 5,6 ´´Removing Red Case´´
(Go to this section if the elevation moves freely and there is no
resistance on the motor itself).
For troubleshooting elevation issues with a Grand Series
machine (EL04, EL05, EL05 LE) see Troubleshooting
Grand Error Messages
2
If the elevation is still not moving, please move onto the next
Author: CT
Contributors: JR,RR, JJ
Elite Model, 1, 2, 3, Pickle 2
TS – My Elevation Is Not Working
Checking Elevation Motor
1. Unscrew control panel and pull it out
and to the side. Be careful not to
disconnect any additional wires.
2. Switch the elevation and feed
connections on the green electronic
board on the back of the control panel.
3. Turn on machine and press either
direction of the elevation button. If the
feed wheel does not turn this control
panel is failing, a new control panel
(EL41B, EL41, EL42, EL43, EL52.P2)
is needed.
Elevation & Feed Connections
Orig. date: 9/20/10
Revised:12/15/2021
Pictures
Control Panel – Open
Advertisement
Related Manuals for LOBSTER SPORTS Elite EL01
Summary of Contents for LOBSTER SPORTS Elite EL01
- Page 1 Elite Model, 1, 2, 3, Pickle 2 TS – My Elevation Is Not Working Objective: To troubleshoot elevation issues for Elite EL01, EL02, EL03, EL0P2 Action Pictures 1 To troubleshoot elevation issues for the EL01, EL02, and EL03, and EL0P2 follow steps below.
- Page 2 Elite Model, 1, 2, 3, Pickle 2 TS – My Elevation Is Not Working step below. Elevation & Feed Connections Checking The Elevation Switch 1. With the control panel still removed, find the 6 wires coming from the Elevation Switch that plug into the circuit board.
- Page 3 Elite Model, 1, 2, 3, Pickle 2 TS – My Elevation Is Not Working 3. Turn OFF the machine, and reconnect the Elevation Wire to the Elevation Tab on the circuit board. 4. Using the Top and Bottom Server Wheels (inside the Server Wheels front opening of the machine), grab the top wheel with one hand, and the bottom wheel with another.
- Page 4 Elite Model, 1, 2, 3, Pickle 2 TS – My Elevation Is Not Working 2. There are 2 large screws in the front bottom section of the Red Case, and 2 large screws on the case side. There are 2 smaller screws located underneath the control panel that secure the red case back.
- Page 5 Elite Model, 1, 2, 3, Pickle 2 TS – My Elevation Is Not Working (Elite model 2&3 and Pickle 2, link, shoulder bolt, location). Checking the Link on the Elevation Motor 1. Check to see if you can move the link off away from the motor shaft (as shown on the 2 images below, the orange arrow indicates the direction it would come off, perpendicular to the link and elevation motor.).
- Page 6 Elite Model, 1, 2, 3, Pickle 2 TS – My Elevation Is Not Working Link arm 1, 2, and should bolt for elite 1 and pickle 2 elevation. Elite 2 & 3 link Elite 1 and Pickle 2 elevation link Author: CT Contributors: JR,RR, JJ Orig.
- Page 7 Elite Model, 1, 2, 3, Pickle 2 TS – My Elevation Is Not Working 2. For the elite 1 and Pickle 2 machines, check to make sure the Should Bolt attaching link arm 1 and link arm 2 is present. If both arms are away from each other, you will need to re- attach them with a shoulder bolt.
- Page 8 Elite Model, 1, 2, 3, Pickle 2 TS – My Elevation Is Not Working 3. Use the nut and bolt you set aside from earlier to attach the elevation link to either location shown below. (The location differs from Elite model 1, Pickle 2, and model 2&3.) Elite 1 link and shoulder bolt Elite 2&3 and Pickle 2 link and shoulder bolt.
- Page 9 Elite Model, 1, 2, 3, Pickle 2 TS – My Elevation Is Not Working Putting The Case Back On The Machine 1. Lift the case over the unit, and guide it over until the yoke pointer is facing the ball exit, and the back panel is facing the handle assembly.