Download Print this page

LOBSTER SPORTS Elite Grand 4 Troubleshooting Instructions

Ts- my machine won't hold a charge (grand machines)

Advertisement

Quick Links

Troubleshooting Instructions
TS- My Machine Won't Hold a Charge (Grand Machines)
Step
Description
Models that Apply: Elite Grand 4, 5, and 5-LE
This guide applies when you try to charge your machine but
the battery does not seem to be holding a charge, or the
LED light on the charger is staying green even when
plugged into the wall outlet and the machine.
Step 1 – Check Reset Switch
If the reset switch is not tripped and the machine still
does not turn on then go to Step 2
Step 2 - Check Main Power Switch
only)
1. Check to make sure the main power switch is in the
on or upright position (This is where the Top is
pushed in and the bottom is sticking out).
2. The main power switch is located underneath the rear
of machine, to the left of the chassis bracket.
Author: JJ
1. On Elite Grand models (EL04, EL05, EL05
LE)
The reset switch is found underneath the
rear of machine, to the right of the case
mounting bracket.
2. If reset switch has tripped, First turn off the
Man Power Switch (A) (found on the left
hand side of the rear of the machine), then
proceed to turn press in the Reset Switch
(B) (*When tripped the Reset Switch will
th
expose 1/16
of an inch of white on its
underbelly). (Found on the right hand rear
side of the machine).
3. Turn the Main Power Switch (A) to the On
position, and then press the power button
(C) on the control panel.
Contributors:
(EL04, EL05, EL05 LE models
Date: 3/18/2022
Tools
Picture
A. Main Power Switch
B. Reset Switch
C. Power Switch
(panel).
Main Power switch (to the
left). Reset Switch (to the
Reset Switch (EL04-EL05 LE)
Main Power Switch
Revised:
right).

Advertisement

loading

Summary of Contents for LOBSTER SPORTS Elite Grand 4

  • Page 1 Description Tools Picture Models that Apply: Elite Grand 4, 5, and 5-LE This guide applies when you try to charge your machine but the battery does not seem to be holding a charge, or the LED light on the charger is staying green even when plugged into the wall outlet and the machine.
  • Page 2: Step 3- Checking The Charger

    Troubleshooting Instructions TS- My Machine Won’t Hold a Charge (Grand Machines) Step 3- Checking the Charger 1. Check the charger by plugging it into the wall outlet (the LED on the charger itself will light up green), and then connect it to the XLR charging port on the machine.
  • Page 3 Troubleshooting Instructions TS- My Machine Won’t Hold a Charge (Grand Machines) Reset Switch Red (right side underneath the machine). XLR wires inside of red case (where the wires come from the XLR charging port). XLR charging port Red Wire (connects to Red tab on Battery).
  • Page 4 Troubleshooting Instructions TS- My Machine Won’t Hold a Charge (Grand Machines) There is 1 black wire coming from the negative section of the battery, this wire should be connected to the Bat Neg (battery negative) section of the circuit board. Author: JJ Contributors: Date: 3/18/2022...
  • Page 5 Troubleshooting Instructions TS- My Machine Won’t Hold a Charge (Grand Machines) Battery Negative coming from battery. Battery negative connected to Bat Neg J12 on circuit board. Author: JJ Contributors: Date: 3/18/2022 Revised:...
  • Page 6 Troubleshooting Instructions TS- My Machine Won’t Hold a Charge (Grand Machines) 3. There is a black wire coming from the XLR charging port (the 3 pronged charging port you connect your charger to), this black wire should connect to the Bat Neg (battery negative) section of the circuit board.
  • Page 7 Troubleshooting Instructions TS- My Machine Won’t Hold a Charge (Grand Machines) Main Power Switch Red wire (underneath the rear of machine). Main Power switch Red Wire (coming through bottom of machine towards circuit board). Author: JJ Contributors: Date: 3/18/2022 Revised:...
  • Page 8 Troubleshooting Instructions TS- My Machine Won’t Hold a Charge (Grand Machines) Main Power Switch Red wire to Bat Pos (battery positive) on circuit board. J8 and J7 locations are both the same current). 1. Check to make sure the XLR charging wires are not loose (either on the circuit board and reset switch where they connect, or where they come out of the...
  • Page 9 If the issue remains after getting a new battery, you will need to contact Lobster Sports to obtain an RA to send the machine into Lobster to get it checked. You can contact Customer Service at 1-800-526- 4041.

This manual is also suitable for:

Elite grand 5Elite grand 5-le