Table of Contents
Advertisement
Quick guide
CARE AND MAINTENANCE
THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.
THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.
In order to receive a more complete assistance, please register
In order to receive a more complete assistance, please
WARNING: unplug the dryer during the cleaning and
your product on www.whirlpool.com.hk
register your product on www.whirlpool.eu/register
maintenance procedures.
www.whirlpool.com.sg
Emptying the water tank after each cycle (see Fig. A).
Pull the container out of the dryer and empty it into a sink or other
suitable drain, then place it back properly. Do not use the dryer
without having inserted the container back in place.
Cleaning the door filter after each cycle (see Fig. B).
Pull the filter out and clean it by removing the lint from the filter
surface under running water or using a vacuum cleaner. For optimal
performance, dry up the filter before inserting it back in place.
Do not use the dryer without having reinserted the filter in place.
Remove the door filter as described below:
1. Open the door and pull the filter upwards.
2. Open the filter and remove the lint from all its parts. Replace the
filter correctly making sure it is fully seated.
Cleaning the bottom filter when the relevant indicator
turns on (see Fig. C).
Pull the filter out and remove the lint from its surface by washing
it under runing water or by using a vacuum cleaner.
However, it is advisable to clean this filter after each cycle to
optimise drying performance.
Do not use the dryer without having reinserted the filter in place.
Remove the bottom filter as described below:
1. Open the bottom cover;
2. Take the handle and pull the filter out.
3. Open the rear side of the filter and remove the lint from the
inner surface of the mesh.
4. Clean the filter chamber avoiding the direct contact with the
fins.
5. Close the rear side of the filter and place it back by checking it
is perfectly integrated into its seat.
6. Lower the filter handle and close the bottom cover.
7. Make sure the air intake is free.
The filters are essential parts for drying. They are intended
to collect the lint formed during the drying process. In case
of clogged filters, the air flow inside the dryer would be
seriously affected: the drying times would be longer, the
energy consumption would increase and the dryer could be
damaged. If these procedures are not carried out properly,
the dryer may not start.
PRODUCT DESCRIPTION
Water Tank
1.
Air Intake
2.
Bottom filter
3.
Door filter
4.
Policies, standard documentation, ordering of spare parts and additional product information can be
Standard documentation and additional product information can be found by:
found by:
• Visiting our website www.whirlpool.com.hk / www.whirlpool.com.sg
• Visiting our website docs.whirlpool.eu and parts-selfservice.whirlpool.com
• Using QR Code
• Using QR Code
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When
contacting our After-sales Service, please state the codes provided on your product's identifi cation plate.
contacting our After-sales Service, please state the codes provided on your product's identifi cation plate.
1
4
3
Cleaning the tumble dryer
Before using the appliance carefully read the Safety
• The external metal, plastic and rubber parts can be cleaned
Instructions.
with a damp cloth.
• Clean the front air intake grille regularly (every 6 months) with
a vacuum cleaner to remove any lint, fluff or dust deposits.
Furthermore, remove any lint deposits from the filters area,
using a vacuum cleaner every so often.
• Do not use solvents or abrasives.
TRANSPORT AND HANDLING
Never lift the dryer by holding it at the worktop.
1. Unplug the dryer.
2. Remove the water from the water tank completely.
3. Make sure that door and water tank are properly closed.
4. If the drain hose is connected to your drainage system,
re-connect it to the back of the dryer (see "Installation" section
in the Safety Instruction
Power consumption
off-mode (Po) - Watts
left-on mode (Pl) - Watts
Programs
Eco Cotton *
Eco Cotton
Synthetics
*Test programme according to IEC 61121 standard. Tested with
maximum rated load capacity and dryness level Extra Dry.
Heat Pump System
The heat pump contains fluorinated greenhouse gases,
contained in a hermetically sealed unit. This sealed unit contains
0,18
kg of the F gas R134a. GWP = 1430 (1 t CO2).
A
C
2
guide).
Kg
kWh
8
1.78
4
1.15
4
0.73
B
EN
0.50
1.00
Minutes
194
135
95
xxxx
xxxxxxxxxxxx
Advertisement
Table of Contents
