Related Manuals for EURA ELH-20H4
Summary of Contents for EURA ELH-20H4
- Page 1 ELECTRONIC HANDLE WITH ACCESS CONTROL ELH-20H4 CARD User manual...
-
Page 2: Table Of Contents
CONTENTS 1. GENERAL CHARACTERISTICS AND INTENDED USE .................4 2. SET CONTENTS .............................4 3. STRUCTURE ............................5 4. OPERATION PRINCIPLE ........................6 5. MOUNTING THE ELECTRONIC HANDLE IN THE DOOR ..............6 5.1. SETTING HANDLE ORIENTATION (LEFT/RIGHT DOORS) ............8 5.1.1 SETTING ORIENTATION - HANDLE FRONT ................8 5.1.2 SETTING ORIENTATION - BACK OF ESCUTCHEON ............8 5.2. - Page 3 INITIAL NOTES Please read these operating instructions carefully before installing, connecting and using the unit. In the case of any problems with understanding the content of this document, please contact the device seller. Installation and start-up of the device by the user are possible if adequate tools are used. Ne- vertheless, it is recommended to have the device installed by qualified personnel.
-
Page 4: General Characteristics And Intended Use
1. GENERAL CHARACTERISTICS AND INTENDED USE An electronic handle with access control simply limits access to protected areas for unauthori- zed persons. It is designed for both left and right doors, and the universal spacing of mounting screws allows for the use of an already installed mortise lock in most cases. The handle body features a proximity key reader (Mifare 13.56 MHz) and a touch numeric key- pad with Bluetooth module. -
Page 5: Structure
3. STRUCTURE Inner side External side Fingerprint reader Battery Touch-sensitive keypad compartment cover CARD with key fob reader Fig. 2. Budowa CARD 127 mm 45 mm 71 mm 24 mm 43 mm 40 mm Fig. 3. Dimensions... -
Page 6: Operation Principle
4. OPERATION PRINCIPLE After receiving a signal from the electronic access control module, the servo motor unlocks the mechanical gearbox, allowing the door to be opened by normal operation of the external handle. The opening is indicated by a sound. The waiting period for handle operation is facto- ry-set to approximately 5 seconds, after which the gearbox is re-locked and the lock returns to standby mode, waiting for the next signal from the electronic access control module. - Page 7 Example of locks installed in standard doors: 50 lub 55 mm 50 lub 55 mm 50 lub 55 mm Fig. 4. Example of locks installed in doors with aluminum profile: 30 lub 35 mm 30 lub 35 mm 30 lub 35 mm Fig.
-
Page 8: Setting Handle Orientation (Left/Right Doors)
5.1. SETTING HANDLE ORIENTATION (LEFT/RIGHT DOORS) All electronic handles are universal and can be mounted on both left and right opening doors. 5.1.1 SETTING ORIENTATION - HANDLE FRONT To determine the direction of the handle with built-in access control, loosen the mounting screw located on the inner side of the escutcheon (Fig. -
Page 9: Installing The Bolt In The Electronic Handle
5.2. INSTALLING THE BOLT IN THE ELECTRONIC HANDLE The bolt should be placed in the slot located in the device body marked with a triangle, and then the counter-locking washer included in the accessory kit should be installed. Note: When installing the bolt, remember to ensure that the slot in the lock body is facing towards the handle. -
Page 10: Installation Diagram
Attention! - The device requires the use of alkaline batteries to function properly. Rechargeable bat- teries should not be used. - It is recommended to install and program the handle with the door open. Once the proper operation is verified, the door can be closed. - After inserting the batteries for the first time, the handle automatically enters the armed state. - Page 11 a. install the external part with connecting sleeves through the door leaf with the previously installed lock b. route the connecting wires coming out of the exter- nal handle above the mortise lock Fig. 12. c. attach a rubber gasket to the back of the handle/ shield Fig.
-
Page 12: Emergency Entrance
g. close the battery compartment. h. program the electronic door handle. Fig. 15 5.5 EMERGENCY ENTRANCE Patent lock cylinder for emergency exit Micro USB port - Emergency power supply for the door handle Fig. 16. In case of the need to enter the premises using the emergency key, insert the emergency key into the cylinder located at the bottom of the device on the access control side and turn the key to the right until resistance is felt. -
Page 13: Reset The Handle
7. PROGRAMMING AND OPERATION OF THE ELECTRONIC HANDLE WITH ACCESS CONTROL To program the ELH-20H4 electronic handle with access control, download the TTLock or TTHotel application from Google Play for Android devices or from the AppStore for iOS de- vices. -
Page 14: Technical Specification
8. TECHNICAL SPECIFICATION PARAMETR Supply voltage 6 V DC Power supply type Alkaline batteries (4 x AA 1.5 V) Current consumption - standby mode / <18uA / 200 mA operation Max. number of users Cards - 200, fingerprint - 200, PIN codes - 200, E-Key - no limit Intended use in doors left-/right-sided Housing material... - Page 15 WARRANTY As the only distributor of the Eura products, Eura-Tech is obliged to ensure efficient war- ranty and post-warranty service. In the countries where Eura-Tech has neither its own service network, nor DOOR-TO-DOOR service, the quality claims are dealt with by autho- rised distributors of the Eura products on the basis of the signed distribution agreements.
- Page 16 Reproduction, dissemination and publication of the entire manual or parts thereof is prohibited without the permission of the author! Eura-Tech Sp. z o.o. reserves the right to change technical parameters and modify the operating manual without notice. It would also like to inform that the most recent version of the operating manual is available on the www.eura-tech.eu website,...
Need help?
Do you have a question about the ELH-20H4 and is the answer not in the manual?
Questions and answers